1. Introduction
Thank you for choosing the METALFISH DH380 V4 Low Profile CPU Cooler. This cooler is engineered to provide efficient heat dissipation for your CPU, especially in compact Mini ITX systems where space is limited. With its 38mm height and 4 heat pipes, it offers robust cooling performance for a wide range of Intel and AMD processors up to 120W D-TDP.
This manual provides detailed instructions for installation, operation, and maintenance to ensure optimal performance and longevity of your CPU cooler. Please read this manual thoroughly before installation.
Image: METALFISH DH380 V4 Low Profile CPU Cooler, showcasing its compact design and key features.
2. Safety Information
Please observe the following safety guidelines to prevent damage to the product or injury:
- Always disconnect power from your computer before installing or removing any components.
- Handle the cooler and CPU with care to avoid damage to pins or delicate components.
- Keep small parts and packaging materials away from children.
- Ensure proper grounding to prevent electrostatic discharge (ESD) damage.
- Do not attempt to modify the cooler. Unauthorized modifications may void your warranty and pose safety risks.
- Use only the provided mounting hardware.
3. Package Contents
Verify that all components are present in your package:
- DH380 V4 CPU Cooler with pre-attached fan
- AMD Mounting Bracket
- Intel Mounting Bracket
- Fixed Nuts (4x)
- Screws (4x)
- Insulation Pads (4x)
- Thermal Grease (1x syringe)
Image: Overview of the DH380 V4 cooler, its specifications, and included accessories.
4. Installation Instructions
The DH380 V4 cooler supports both Intel and AMD platforms. Follow the specific instructions for your CPU socket type.
4.1. AMD Platform Installation
Image: Step-by-step diagram for installing the DH380 V4 cooler on an AMD motherboard.
- Accessories Display: Identify the AMD bracket (A), fixed nuts (B), screws (C), insulation pads (D), and thermal grease (E).
- Step 1: Prepare Fixed Nuts: Stick the black insulation pads onto the 4 fixed nuts.
- Step 2: Attach Bracket to Radiator: Install the AMD socket bracket onto the radiator.
- Step 3: Prepare Motherboard: Remove the original AMD CPU retention bracket from the motherboard, but keep the original backplate of the motherboard in place.
- Step 4: Apply Thermal Grease: Clean the top surface of your CPU thoroughly. Apply a small, even amount of the provided thermal grease onto the CPU's integrated heat spreader (IHS).
- Step 5: Position Cooler: Carefully place the cooler onto the CPU, aligning the mounting holes. Adjust the screw positions on the bracket according to the motherboard installation holes.
- Step 6: Secure Cooler: From the back of the motherboard, tighten the four fixed nuts with the insulation pads to secure the cooler. Tighten them in a diagonal pattern until snug, but do not overtighten.
- Step 7: Connect Cables: Connect the 4-pin fan cable to the CPU_FAN header on your motherboard. If your cooler is the ARGB version, connect the ARGB cable to the 5V+3pin ARGB header on your motherboard. (Note: ARGB version only)
4.2. Intel Platform Installation
Image: Step-by-step diagram for installing the DH380 V4 cooler on an Intel motherboard.
- Accessories Display: Identify the Intel bracket (A), fixed nuts (B), screws (C), insulation pads (D), and thermal grease (E).
- Step 1: Prepare Fixed Nuts: Stick the black insulation pads onto the 4 fixed nuts.
- Step 2: Attach Bracket to Radiator: Install the Intel socket bracket onto the radiator.
- Step 3: Apply Thermal Grease: Clean the top surface of your CPU thoroughly. Apply a small, even amount of the provided thermal grease onto the CPU's integrated heat spreader (IHS).
- Step 4: Position Cooler: Carefully place the cooler onto the CPU, aligning the mounting holes. Adjust the screw positions on the bracket according to the motherboard installation holes.
- Step 5: Secure Cooler: From the back of the motherboard, tighten the four fixed nuts with the insulation pads to secure the cooler. Tighten them in a diagonal pattern until snug, but do not overtighten.
- Step 6: Connect Cables: Connect the 4-pin fan cable to the CPU_FAN header on your motherboard. If your cooler is the ARGB version, connect the ARGB cable to the 5V+3pin ARGB header on your motherboard. (Note: ARGB version only)
5. Operating Instructions
Once installed, the METALFISH DH380 V4 CPU cooler operates automatically, controlled by your motherboard's fan speed settings (if PWM is enabled). The 4-pin PWM connector allows for dynamic fan speed adjustment based on CPU temperature, optimizing cooling performance and noise levels.
- Fan Speed: The fan operates within a range of 900 to 2800 RPM (±10%).
- Noise Level: At typical operating conditions, the noise level ranges from 18 to 28 dBA (±10%).
- Airflow: The fan provides an airflow of 12.59 to 38.9 CFM (±10%).
- TDP Support: This cooler is designed to handle CPUs with a Thermal Design Power (TDP) of up to 120W.
You can typically monitor CPU temperatures and fan speeds through your motherboard's BIOS/UEFI settings or dedicated software provided by your motherboard manufacturer.
6. Maintenance
Regular maintenance helps ensure optimal performance and extends the lifespan of your CPU cooler:
- Dust Removal: Periodically (every 3-6 months, or more often in dusty environments) use compressed air to clean dust from the heatsink fins and fan blades. Ensure the fan is held stationary during cleaning to prevent damage to the bearing.
- Thermal Paste: If you remove the cooler for any reason, it is recommended to clean off the old thermal paste from both the CPU and the cooler's base and apply fresh thermal paste before reinstallation.
- Fan Inspection: Check the fan for any signs of wear, damage, or excessive noise. If the fan becomes excessively loud or stops spinning, consider replacing it.
7. Troubleshooting
If you encounter issues with your CPU cooler, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| CPU Overheating | Improper thermal paste application, loose cooler mounting, insufficient airflow in case, fan not spinning. | Re-apply thermal paste, ensure cooler is securely mounted, check case airflow, verify fan connection and operation. |
| Fan Not Spinning | Fan cable disconnected, faulty fan, BIOS settings. | Check 4-pin fan connection to CPU_FAN header, test fan on another header if available, check BIOS fan control settings. |
| Excessive Fan Noise | Dust buildup, fan bearing wear, fan hitting cables. | Clean fan and heatsink, ensure no cables are obstructing fan blades. If noise persists, consider fan replacement. |
| ARGB Lighting Not Working | ARGB cable disconnected, incorrect ARGB header (e.g., 12V RGB instead of 5V ARGB), software issue. | Ensure 5V+3pin ARGB cable is connected to the correct motherboard header. Check motherboard software for ARGB control. |
8. Specifications
Detailed technical specifications for the METALFISH DH380 V4 CPU Cooler:
| Feature | Specification |
|---|---|
| Model Number | DH380 V4 |
| Cooler Type | Low Profile |
| Dimensions (L x W x H) | 110mm x 92mm x 38mm |
| Fan Size | 92mm x 92mm x 15mm |
| Heat Pipes | 4 heat pipes, Φ6mm |
| Bearing Type | Fluid Bearing (Hydraulic) |
| Fan Speed | 900 - 2800 RPM ±10% |
| Fan Airflow | 12.59 - 38.9 CFM ±10% |
| Static Pressure | 0.29 - 2.19 mmH2O ±10% |
| Noise Level | 18 - 28 dBA ±10% |
| Fan Life (MTTF) | ≥40000h (at 25°C) / 50000 hrs |
| Rated Current | 0.2A |
| Rated Voltage | 12V DC |
| Power Interface | 4PIN PWM |
| TDP Support | 120W D-TDP |
| Supported Intel Sockets | LGA 1851, 1700, 1200, 115x (1150, 1151, 1155, 1156), 1366, 2011, 2066 |
| Supported AMD Sockets | AM5, AM4, AM3(+), AM2(+), FM1, FM2(+) |
| Certification | CE, FCC, RoHS |
9. User Tips
Insights from other users to enhance your experience:
- Check All Parts: Before starting installation, carefully check that all included accessories, especially small parts like insulation washers, are present.
- Installation Clarity: The included paperwork and diagrams are generally clear. Follow them closely for a smooth installation process.
- Performance Expectation: This cooler is noted for its excellent performance relative to its size, capable of handling CPUs up to 120W D-TDP, even under full load, keeping temperatures well below 100 degrees Celsius in open-air setups.
- Fan Noise: While generally quiet, some users note the fan can be slightly louder at higher RPMs. The fan is standard 92x15mm and can be swapped with a quieter alternative if desired.
- Thermal Paste Application: Ensure a clean and even application of thermal paste for optimal heat transfer.
10. Frequently Asked Questions (FAQ)
- Q: Is this cooler compatible with my CPU?
- A: Please refer to the 'Specifications' section for a comprehensive list of supported Intel and AMD CPU sockets. Ensure your motherboard's socket type is listed.
- Q: How do I know if the cooler is installed correctly?
- A: After installation, ensure the cooler is firmly seated and does not wobble. Check your system's BIOS/UEFI or monitoring software for CPU temperature readings. Temperatures should be within safe operating limits (typically below 80-90°C under load).
- Q: Can I replace the fan?
- A: Yes, the fan is a standard 92x92x15mm size and can be replaced with another compatible fan if you wish to change its performance or noise characteristics.
- Q: What is the purpose of the insulation pads?
- A: The insulation pads prevent direct contact between metal mounting hardware and the motherboard's PCB, protecting against short circuits and ensuring proper electrical isolation.
11. Warranty and Support
For warranty information and technical support, please refer to the official METALFISH website or contact your retailer. Keep your proof of purchase for warranty claims.
A digital version of this user manual is available for download at METALFISH DH380 V4 User Manual (PDF).