ludengchaoshi Industrial Retro Ceiling Fan

Contents

User Manual: Industrial Retro Ceiling Fan

Model: Industrial Retro Ceiling Fan

Brand: ludengchaoshi

Introduction

This manual provides detailed instructions for the safe installation, operation, and maintenance of your new ludengchaoshi Industrial Retro Ceiling Fan. Please read all instructions carefully before beginning installation and retain this manual for future reference.

This model is designed without a photoelectric light feature.

A comprehensive user manual in PDF format is available for download: View User Manual (PDF)

Important Safety Instructions

WARNING: To avoid fire, shock, and serious personal injury, please read the following instructions carefully.

  1. Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
  2. Before installing the fan, disconnect the power by removing fuses or turning off circuit breakers.
  3. Make sure all electrical connections comply with local codes, ordinances, or National Electrical Codes. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.
  4. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blades.
  5. If you are mounting the fan on a ceiling outlet box, use a metal outlet box. Secure the box directly to the building structure. The outlet box and its support must be able to support the moving weight of the fan (at least 50 lbs.). Do not use a plastic outlet box. Attach the mounting bracket by using the hardware supplied with the ceiling outlet box.
  6. If you are mounting the fan to a joist, make sure it is strong enough to support the moving weight of the fan (at least 50 lbs.).
  7. After installing the fan, make sure all the connections are secured. This will prevent the fan from falling.
  8. Do not insert anything into the fan blades while the fan is operating.
  9. Turn the fan off and wait for it to stop before reversing fan direction.
  10. To reduce risk of electrical shock and personal injury, do not install the fan on a sloped ceiling.
  11. To reduce the risk of electrical shock and personal injury, do not use this fan with any solid-state speed control device.
  12. To reduce risk of personal injury, use only the two steel screws and lock washers provided with the fan for mounting the outlet box.

Parts List

Before installation, unpack your fan and check all contents against the list below. Remove parts from packaging as needed to prevent damage.

Ref.# Description Quantity
1Hanger Bracket1
2Canopy1
3Downrod Assembly1
4Coupling Cover1
5Fan Motor Assembly1
6Blade5
7Blade Decorative Plate1
8Plastic Cap1
9Remote Control1

Black ceiling fan installed in a modern room Figure: Example of the ceiling fan installed (Black finish).

Silver wood grain ceiling fan installed in a library-like setting Figure: Example of the ceiling fan installed (Silver wood grain finish).

Installation Instructions (Without Light)

WARNING: The fan must be hung with at least 230 cm (approximately 7.5 feet) of clearance from the floor to the blades.

Step 1: Secure Hanger Bracket

Securely attach the hanger bracket to the ceiling joist using the lag bolt, flat washer, and spring washer supplied. (Refer to Figure 1 in the PDF manual for visual guidance).

Step 2: Install Fan Blades

Install the fan blades and blade decorative plate by aligning the holes on the blade and plate with the holes on the fan motor assembly. Secure them using the provided set screws. Ensure the set screws are tight and the blades are properly seated. (Refer to Figure 2 in the PDF manual for visual guidance).

Exploded view diagram of the fan motor components Figure: Exploded view of the fan motor, highlighting internal components.

Step 3: Prepare Downrod Assembly

Loosen the set screws in the Hanger Ball assembly until the ball slides carefully down the downrod. Remove the Pin from the downrod. (Refer to Figure 3 in the PDF manual for visual guidance).

Step 4: Attach Downrod to Canopy and Coupling Cover

Remove and save the clevis pin and hairpin of the downrod. Put the downrod through the canopy and coupling cover. (Refer to Figure 4 in the PDF manual for visual guidance).

Black ceiling fan installed with a hanging rod, showing available rod lengths Figure: Ceiling fan with hanging rod options (12.5cm and 20cm shown).

Step 5: Connect Downrod to Support

Loosen two set screws on the downrod support and then place the downrod into the downrod support. Thread the electrical wires and the earth wire through the downrod. Align the Clevis Pin holes in the Downrod with the holes in the Downrod Support. Be sure to push the straight leg of the Hairpin Clip through the hole near the end of the Clevis Pin until the curved portion of the Hairpin snaps around the Clevis Pin. Finally, re-tighten the two set screws. (Refer to Figure 5 in the PDF manual for visual guidance).

WARNING: It is critical that the clevis screw in the downrod support is properly installed and the set screws are securely tightened. Failure to verify the clevis screw, hairpin clip, and set screws are properly installed could result in the fan falling.

Step 6: Hang Fan Assembly

Carefully lift the fan and set the downrod/hanger ball assembly on the hanger bracket attached to the ceiling joist. Be sure the groove in the ball is properly aligned with the tab on the hanger bracket. (Refer to Figure 6 in the PDF manual for visual guidance).

Step 7: Electrical Connections

WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring.

  1. Connect 220-240V main power (dwelling) to the Terminal Block located on the hanger bracket.
  2. Plug the receiver in the hanger bracket with the flat side facing up.
  3. Insert the 3P connector of hanger bracket into the AC POWER INPUT socket of receiver.
  4. Insert the 3P motor connector of fan motor assembly into the 3P MOTOR socket of receiver.
  5. Connect the 1P yellow/green connectors of fan motor assembly and hanger bracket. (Refer to Figure 7 in the PDF manual for wiring diagram).

Step 8: Mount Canopy

Mount the canopy by tightening the two screws. (Refer to Figure 8 in the PDF manual for visual guidance).

Step 9: Install Rubber Plug

Install the rubber plug into the motor axis. (Refer to Figure 9 in the PDF manual for visual guidance).

Operation

Remote Control Setting and Operation

The fan uses RF wireless digital transmission technology for one-on-one control. The remote control allows operation from any angle within the allowable space.

Hand holding a remote control for the ceiling fan, with a wall switch next to it Figure: Remote control and wall switch for dual-control.

Remote Control Functions:

  1. Turn off all loads (Fan and any connected accessories)
  2. Fan speed control
  3. LED indicator light (on remote control)
  4. Turn on the light (Function not applicable to this fan model, which has no photoelectric light)
  5. Fan off
  6. Fan positive and negative rotation control
  7. Fan timing control

The remote control uses a pair of 1.5V batteries. Test the battery; if the LED indicator on the remote does not light up, please replace the battery.

Important Tips About Remote:

  • Pairing: The remote control and receiver are paired using a learning code. Within 5 seconds of the controller being powered on, direct the remote control towards the controller. Press and hold the total key for about 5 seconds. A beep indicates successful learning. After successful learning, press the gear to use it normally. (Note: If powered on for more than one minute, learning will not be accepted).
  • If the remote control cannot control the controller, check if the battery is loaded correctly.
  • Low battery voltage affects the remote control distance and may cause remote control failure. Replace batteries in time.
  • When not in use for a long time, remove the battery from the remote control.
  • During installation, ensure the ceiling cover of the fan does not compress any wires, which could cause wires to break and short circuit.

Important: Pairing Between Remote and Receiver

  1. Turn ON the power supply. Within 30 seconds, press and hold the transmitter's "RAN ON/OFF" button for 5 seconds. A "beep" will be heard, indicating successful pairing. All functions should now work normally.
  2. Important: The initial pairing step must be performed within 30 seconds of power being turned on.
    • When pairing multiple fans, ensure the isolation switch or power supply to the first installed fan is turned off prior to pairing further fans (e.g., pair one fan at a time).
    • Ensure the isolation switch is kept to the ON position. The isolation switch is not to be used as a light switch as this will damage and make the remote receiver inoperable.
  3. If the transmitter functions are not working, check the battery orientation and power level. Low battery voltage will affect the transmitter's functions and fan operation. Other remote controls nearby using the same frequency may cause interference with the fan's receiver.
  4. Remove batteries from the transmitter if leaving unused for an extended period of time.
  5. Remote supports 200W maximum on lighting side (Note: This fan model does not include a light, so this feature is not applicable).

Maintenance

  1. Periodic cleaning of your new ceiling fan is the only maintenance that is needed.
  2. When cleaning, use only a soft brush or lint-free cloth to avoid scratching the finish.
  3. Abrasive cleaning agents are not required and should be avoided to prevent damage to the finish.

WARNING: Do not use solvents when cleaning your ceiling fan. It could damage the motor and create the possibility of electrical shock.

Recommended: Periodically check that the blade setscrews to the fan motor are secure and tight.

Before carrying out any cleaning or maintenance work, always make sure that the appliance is disconnected.

Troubleshooting

Balancing Fan / Wobbling Trouble Shooting

Please note that all ceiling fans are not the same; even in the same model, some may move more or less than others. Movement of a couple of centimeters is quite acceptable and does not suggest the fan will fall down.

Even though all blades are weighted and grouped by weight, it is impossible to eliminate wobble altogether. This should not be considered a fault. Ceiling fans tend to move during operation due to the fact that they are not generally rigidly mounted.

Try the following to reduce a wobbling fan:

  1. Check that all of the blade mounting screws are tightened and secure.
  2. Wobbling problems may result from inconsistent blade level. To check the blade level, measure the distance from each blade tip to the ceiling.
    Note: If measurements are inconsistent:
    • Be sure the blade mount screws are not too tight or too loose, which may cause wobbling due to an unlevel blade tip.
    • An out-of-shape blade can cause wobbling. Check by removing the blade and placing it on a flat surface.
  3. Blade tracking may be checked simply by use of a household ruler. Place the ruler vertically against the ceiling and even with the outside leading edge of a blade. Note the distance of the edge of a blade compared to the others. Turn the blade slowly by hand to check the remaining blades. If a blade is not in alignment, the blade is either out of shape, warped, or the blade screws are not evenly tightened or either loose.

Balancing Kit

A Balancing Kit has been provided to assist with reducing a wobble. Please retain the kit as it may become useful should the fan develop a wobble in the future. Instructions on how to use the Balancing kit can be found within the Kit.

Protective Functions of the Receiver

  • Lock Protection: The DC motor has a built-in safety feature against blade or motor obstruction during operation. If something obstructs the fan blades or motor, the motor will keep trying to run and then stop operation after about 30 seconds of interruption. Remove any obstacles and reset the fan by turning it off via remote transmitter and then turning it back on.
  • Overload Protection (Current Limit): The device will limit the maximum current output from the receiver/drive if the fan load has increased abnormally.

Important Reminders:

  • Receiver must be correctly installed in the mounting bracket on the fan.
  • If the transmitter cannot control the receiver, check the battery charge.
  • If the transmitter cannot control the receiver, check for interference from similar remote-controlled products nearby.
  • Low battery power affects transmitter sensitivity and signal reception; replace batteries if low.
  • Remove batteries from the transmitter if unused for a long time to avoid leaks.
  • Isolation Switch must be connected in the line.
  • If power is cut to the unit (e.g., blackout) and then restored, the fan will come on.

Specifications

Feature Detail
Brand Nameludengchaoshi
Item TypeCeiling Fans
StyleModern Style
Installation MethodAssembly
Control MethodREMOTE CONTROL
Switch TypeREMOTE CONTROL
Is DimmableNo
Power SourceAC
CertificationCE, ROHS
OriginMainland China
Hign-concerned ChemicalNone
Voltage Options110V (42 inches), 120V (52 inches)
Package Length55 cm
Package Width24 cm
Package Height21 cm
Package Weight5.5 kg

User Tips

  • For optimal performance and quiet operation, ensure all mounting screws and blade screws are securely tightened during installation and periodically checked.
  • If you experience any wobbling, first verify blade balance and tightness before using the provided balancing kit.
  • Always turn off power at the circuit breaker before performing any maintenance or troubleshooting.
  • Keep the remote control in a safe place and remove batteries if not using the fan for extended periods to prevent battery leakage.
  • Consider the ceiling height when choosing the hanging rod length for best airflow and aesthetic appeal.

Frequently Asked Questions (FAQ)

Q: My fan is wobbling. What should I do?
A: First, check that all blade mounting screws and the hanger bracket screws are tight. Ensure blades are level and not warped. A balancing kit is provided to help resolve wobbling issues; refer to its instructions.
Q: The remote control isn't working.
A: Check the batteries in the remote control and ensure they are correctly inserted and have sufficient charge. If the fan is new, ensure the remote and receiver are properly paired according to the "Important: Pairing Between Remote and Receiver" section.
Q: Why does the fan stop after running for a short time?
A: The fan has a lock protection feature. If something obstructs the blades or motor, it will stop after about 30 seconds. Remove any obstructions and reset the fan by turning it off and on with the remote.
Q: Can I install this fan on a sloped ceiling?
A: No, the safety instructions explicitly state not to install this fan on a sloped ceiling to reduce the risk of electrical shock and personal injury.

Warranty and Support

For any issues not covered in this manual or for warranty inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

For further technical details or diagrams, please refer to the full PDF manual: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.