Keenkee M00184A

Contents

Black Metal 90 Degree Angle Corner Bracket User Manual

Model: M00184A | Brand: Keenkee

1. Introduction

This manual provides essential information for the safe and effective use of your Keenkee Black Metal 90 Degree Angle Corner Brackets. These versatile L-shaped brackets are designed for reinforcing and supporting various wooden furniture and shelving systems. Please read all instructions carefully before installation and use to ensure product longevity and user safety.

2. Safety & Warnings

Important Safety Information

Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the product and its accessories out of reach of children under 3 years old.
  • Strictly prohibit overloading. Overloading may cause connection parts to break or screws to come out, leading to furniture collapse, injuries, or property damage.
  • When installing, wear protective gloves to avoid injury from sharp metal edges.
  • Use screws that match the diameter of the angle code holes. Oversized screws may deform or break the bracket.
  • Do not over-tighten screws, as this may cause thread breakage or damage to the sheet material.
  • Regularly check for loose screws, rust, or deformation. Replace immediately if found.

3. Product Specifications

Feature Detail
Product Name Corner Bracket
Model Number M00184A
Batch/Serial Number WXM00184A-2601
Type 90 Degree Angle Corner Bracket (L-shaped)
Material Iron (3mm thick steel)
Color Black
Dimensions (approx.) Length: 4" (102mm), Height: 2.3" (59mm), Width: 1.2" (30mm)
Screw Slot Dimensions Length: 1.2" (30mm), Width: 0.35" (8.8mm)
Included Screws 10 screws (0.35" head diameter, 0.7" length)
Package Contents 2 pcs Corner Brackets, 10 Screws
DIY Supplies Category Woodworking
Diagram showing dimensions of the Keenkee M00184A corner bracket and included screws.
Figure 1: Product Dimensions and Package Contents
Two black L-shaped corner brackets, top-down view.
Figure 2: Keenkee M00184A Corner Brackets

4. Setup & Installation

These instructions apply to various types of metal furniture corner brackets, including L-shaped, T-shaped, and straight bar-shaped ones.

Installation Steps:

  1. Positioning: Place the angle peg tightly against the corner angle between the two connection surfaces, maintaining a 90° angle or the angle required by your design.
  2. Pre-drilling (Recommended): To reduce the risk of wood cracking, it is recommended to use a drill bit with a diameter slightly smaller than the screws to create initial pilot holes.
  3. Fixing: Insert the screws through the holes in the corner brackets. Use a screwdriver or electric drill to tighten them until the corner brackets are tightly attached to the surface of the panel.
  4. Check: Ensure that all screws are not loose and the corner brackets are not deformed after installation.
Two black L-shaped corner brackets, one with screws inserted, demonstrating installation.
Figure 3: Bracket with Screws for Installation
Black L-shaped corner bracket installed on the underside of a wooden shelf.
Figure 4: Example of Installed Corner Bracket

Installation Video:

Video 1: Product demonstration and installation guide for the Keenkee corner brackets.

5. Usage Limitations

  • This product is only suitable for indoor dry environments. Do not use it in damp or acidic/basic conditions.
  • This product is an auxiliary support component and cannot replace the main load-bearing structure.
  • Prohibition of installation on surfaces such as glass, thin-walled metal pipes (with a wall thickness of less than 1mm), gypsum boards, foam bricks, and ceramic tile finishes that cannot provide sufficient holding force for nails.

6. Maintenance

  • Regularly check whether the screws are loose.
  • If any rust or deformation is found on the brackets or screws, they should be replaced immediately.

7. Troubleshooting

  • Loose Brackets: If brackets become loose, check if screws are properly tightened. Ensure the mounting surface is suitable and not compromised. Re-tighten screws or replace if necessary.
  • Wobbling Furniture/Shelves: This often indicates insufficient support or improper installation. Verify that the correct number of brackets are used for the load and that they are securely fastened according to the installation instructions.

8. User Tips

  • Many users find these brackets to be very sturdy and effective when installed correctly.
  • The elongated screw slots offer flexibility for precise alignment during installation, making the process more forgiving.
  • Consider using a level during installation to ensure shelves and furniture are perfectly straight.

9. Manufacturer & Support Information

Manufacturer:

Company Name: Shenzhen Wenxinmeijia Household Product Co., Ltd

Full Address: B1C031 #5 Plaza, Huanancheng Pinghu, Longgang District Shenzhen City

Email: servicenter@keenkee.online

Telephone: 86-13164762726

EU Authorized Representative:

AR Company Name: GAVIMOSA CONSULTORIA, SOCIEDAD LIMITADA

Full Address: CASTELLANA 9141, 28046 Madrid, Spain

Email: compliance.gavimosa@outlook.com

Telephone: 34-688185858

For further assistance, please refer to the official user manual PDF: View User Manual (PDF)

10. Compliance Information

CE Marks: This product complies with the health, safety, and environmental protection standards.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.