FGHGF Portable AMP

Contents

Hifi Rechargeable Headphone Amplifier User Manual

Model: Portable AMP | Brand: FGHGF

1. Introduction

Thank you for purchasing the Hifi Rechargeable Headphone Amplifier. This device is designed to enhance your audio experience by providing clear, powerful, and realistic stereo sound for your headphones. Its exquisite, compact, and lightweight design makes it highly portable and easy to carry.

Key features include a 3.5mm AUX input and output, a signal-to-noise ratio greater than 120dB, and a very low total harmonic distortion plus noise (THD+N) of 0.0003%. The amplifier is built with a stylish aluminum matte surface for comfortable handling and durability, and it houses a 1500mAh rechargeable lithium battery offering over 8 hours of continuous operation. It is widely compatible with various digital devices such as MP3 players, MP4 players, mobile phones, and computers.

2. Package Contents

Please check the package for the following items:

  • 1 x Hifi Rechargeable Headphone Amplifier

Note: Only the above package content is included. Other products shown in promotional images are not part of this package.

3. Safety & Warnings

  • This product is intended for adult use only.
  • Keep out of reach of children and pets to prevent accidental injury or ingestion.
  • Always check if the installation and connections are correct before use.
  • If you experience abnormal noise or equipment error after installation or during operation, discontinue use immediately.
  • Follow all instructions for proper use; misuse may cause harm or damage to the device.
  • Store the device in a dry and shady place, away from high temperatures, excessive humidity, and direct sunlight.

4. Product Overview

Familiarize yourself with the different parts of your headphone amplifier:

Interface Diagram of Headphone Amplifier

Figure 1: Interface Diagram

Top Panel Components:

  • OUTPUT: Headset Jack (3.5mm audio output for headphones)
  • INPUT: Connection for the Sound Source (3.5mm audio input)
  • POWER: Power indicator LED
  • ON/OFF Switch/Volume control: Rotary knob to power on/off and adjust audio volume.

Bottom Panel Components:

  • GAIN (H/L): Two-stage Gain Switch (H for High Gain, L for Low Gain)
  • CHG: Charging indicator LED
  • USB/Power: Micro USB port for charging and power input.

5. Setup

  1. Initial Inspection: Before first use, carefully inspect the amplifier for any signs of damage. If any damage is found, do not use the device and contact support.
  2. Connect Audio Source: Using a 3.5mm audio cable (not included), connect your audio source (e.g., smartphone, MP3 player, laptop, DVD player) to the INPUT jack on the amplifier.
  3. Connect Headphones: Plug your headphones into the OUTPUT jack on the amplifier.
Connectivity Diagram for Headphone Amplifier

Figure 2: Connectivity Diagram

6. Operating Instructions

6.1 Power On/Off and Volume Control

  • To power on the amplifier, rotate the ON/OFF Switch/Volume control knob clockwise. The POWER indicator LED will illuminate.
  • Continue rotating clockwise to increase the audio volume.
  • To decrease the volume, rotate the knob counter-clockwise.
  • To power off the amplifier, rotate the knob fully counter-clockwise until it clicks and the POWER indicator LED turns off.

6.2 Gain Switch

The amplifier features a two-stage gain switch (H/L) to optimize audio output for different headphones and listening preferences:

  • L (Low Gain): Suitable for most standard headphones and in situations where less amplification is needed. This setting helps maintain clarity and reduce potential noise.
  • H (High Gain): Provides increased amplification, ideal for higher impedance headphones or when you require more power and volume output.

Adjust the gain setting based on your headphones' specifications and your desired listening level.

7. Charging the Amplifier

The amplifier is equipped with a built-in 1500mAh rechargeable lithium battery.

  1. Connect a micro USB cable (not included) to the USB/Power port on the bottom panel of the amplifier.
  2. Connect the other end of the USB cable to a suitable USB power source, such as a computer's USB port or a USB wall adapter (5V).
  3. The CHG indicator LED will illuminate to show that the device is charging. The LED will change or turn off once charging is complete (refer to specific LED behavior if detailed in future updates).

Important Note:

  • It is not recommended to use the amplifier while it is charging, as current interference may occur during charging, which can cause audible noise.

8. Maintenance

  • Cleaning: To clean the amplifier, use a soft, dry, lint-free cloth. Do not use liquid cleaners, abrasive cleaning agents, or solvents, as these can damage the finish or internal components.
  • Storage: When not in use, store the amplifier in a dry place, away from direct sunlight, extreme temperatures, and high humidity. Keep it away from children.
  • Handling: Avoid dropping the device or subjecting it to strong impacts, which can cause internal damage.

9. Troubleshooting

ProblemPossible CauseSolution
No sound outputAmplifier is off; Volume is too low; Cables are not connected properly; Audio source issue.Ensure amplifier is powered on and volume is up. Check all 3.5mm audio cable connections. Verify the audio source is playing and its volume is adequate.
Distorted sound or noiseUsing while charging; Poor quality audio cables; Gain setting too high for headphones; Audio source distortion.Avoid using the amplifier while charging. Try different audio cables. Adjust the gain switch (try 'L' setting). Test with a different audio source.
Amplifier does not turn onBattery is depleted.Connect the amplifier to a USB power source and charge it.

10. Specifications

FeatureDetail
Product NameHiFi Rechargeable Headphone Amplifier Portable AMP
Audio Input3.5mm AUX
Audio Output3.5mm AUX
Signal-to-Noise Ratio (SNR)>120dB
Total Harmonic Distortion + Noise (THD+N)0.0003%
Battery TypeRechargeable Lithium Battery
Battery Capacity1500mAh
Continuous Working Time>8 hours
Charging PortMicro USB
Recommended Headphone Max Impedance< 32 Ohm
MaterialAluminum Alloy
ColorBlack
Dimensions (L x W x H)11.2 cm x 6.2 cm x 1.1 cm
Dimensions of Headphone Amplifier

Figure 3: Product Dimensions

11. User Tips

  • For the best audio experience, avoid using the amplifier while it is connected to a charger. This can prevent potential noise interference.
  • Experiment with both 'L' (Low Gain) and 'H' (High Gain) settings to find the optimal sound level and clarity for your specific headphones and audio source.

12. Warranty & Support

Manufacturer Information:

Company: Taiyuan yingxinfeng technology co., ltd
Address: Room 1304, 13th floor, No.3 Zhichuang City, No.1 Automobile Trade Road, Xuefu Industrial Park, Shanxi Transformation Comprehensive Reform Demonstration Zone Code: 030000
Email: WiNdLmsOoqw2lE@163.com
Phone: +86 13670049821

EU Authorized Representative:

Company: Prolinx GmbH
Address: Duesseldorf / Brehmstr.56 / 40239, Germany
Email: eu@eulinx.eu
Phone: +49 21131054698

For warranty claims or technical support, please contact the manufacturer or the authorized representative using the details provided above.

© 2024 FGHGF. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.