STC-3008 STC-3008

Contents

STC-3008 Dual Digital Temperature Controller User Manual

Model: STC-3008

Introduction

The STC-3008 is a dual digital temperature controller designed for precise temperature management in various applications, including home refrigeration, heating, and cooling systems. It features two independent relay outputs, allowing for simultaneous control of heating and cooling devices or two separate temperature zones. This manual provides essential instructions for the safe and effective use of your STC-3008 controller.

Front view of the STC-3008 controller showing dual digital displays and control buttons, with two temperature probes.

Front view of the STC-3008 controller showing dual digital displays and control buttons, with two temperature probes.

Safety Information

  • Electrical Work: Only qualified professionals are permitted to perform electrical wiring and installation. Do not attempt to disassemble the device without proper authorization.
  • Power Off: Always ensure the power supply is completely disconnected before installing or performing any maintenance on the circuit.
  • Overheating/Malfunction: If you observe any signs of overheating, sparks, or a malfunction, immediately cut off the power supply and replace the unit.
  • Environment: Keep the device dry and clean. Avoid overloading, water contact, and rough handling to prevent damage and ensure safe operation.
  • Choking Hazard: This product may contain small parts. Keep out of reach of children under 3 years of age.

Product Overview and Dimensions

The STC-3008 features a compact design with clear digital displays for easy monitoring. It comes with two temperature probes, each approximately 1 meter in length.

STC-3008 Temperature Controller with dimensions (86mm x 70mm x 27mm/35mm) and two 1-meter probes.

STC-3008 Temperature Controller with dimensions (Length: 86mm, Width: 70mm, Height: 27mm, Depth including clips: 35mm) and two 1-meter probes.

STC-3008 controller with two 1-meter temperature probes.

The STC-3008 controller includes two temperature probes, each 1 meter in length.

Setup and Wiring

Before proceeding with installation, ensure the power supply is off. Verify that the voltage and current ratings of your power source and connected devices match the specifications of the STC-3008 controller (available in 12V, 24V, and 220V versions).

  1. Power Off: Confirm that the voltage and current match the label on the device. Install the circuit only when the power is off.
  2. Secure Mounting: Securely fix the controller in its desired location. Properly bundle and route all wires, then close the cover/panel.
  3. Wiring Connections: Refer to the wiring diagrams below for correct connection of the power supply, sensors, and loads (heating/cooling).

Wiring Diagram on Device

Detailed view of the STC-3008 control panel and wiring diagram on the device, indicating power supply, sensor, and relay connections.

This diagram shows the terminal connections on the STC-3008. Terminals 1 & 2 are for power supply (110-220VAC, 12V, or 24V). Terminals 3 & 4 are for Sensor 1, and 5 & 6 for Sensor 2. Terminals 7 & 8 are for Output 1 (10A/220VAC), and 9 & 10 for Output 2 (10A/220VAC).

Same Power Supply Wiring

Use this configuration when the controller and the loads (heating/cooling) share the same power source.

Wiring diagram for STC-3008 using a single power supply for both the controller and the heating/cooling loads.

Wiring diagram for STC-3008 where the main power supply also powers the heating and cooling loads. Ensure correct polarity for DC versions.

Independent Power Supply Wiring

Use this configuration when the controller and the loads (heating/cooling) use separate power sources. This is often necessary for higher power loads or different voltage requirements.

Wiring diagram for STC-3008 using independent power supplies for the controller and the heating/cooling loads.

Wiring diagram for STC-3008 using independent power supplies for the controller (Power supply 1) and the heating/cooling loads (Power supply 2). This allows for greater flexibility in system design.

Operating Instructions

The STC-3008 features two digital displays and four buttons for temperature adjustment and mode selection. The left display (red) typically shows the current temperature or the set start temperature, while the right display (blue) shows the set stop temperature.

Control Buttons:

  • Up Button (Start 1): Used to increase the set start temperature for output 1.
  • Down Button (Stop 1): Used to decrease the set stop temperature for output 1.
  • Up Button (Start 2): Used to increase the set start temperature for output 2.
  • Down Button (Stop 2): Used to decrease the set stop temperature for output 2.

To control the thermostat, gently press or switch the operation buttons to adjust the desired temperature settings. The "Work lights" indicate when an output is active.

Detailed programming instructions for setting heating/cooling modes, temperature differentials, and calibration are typically found in the full user manual. Please refer to the PDF manual for advanced settings.

Maintenance and Care

  • Cleaning: Keep the device dry and clean. Use a soft, dry cloth to wipe the surface. Do not use abrasive cleaners or allow water to enter the device.
  • Handling: Avoid rough handling, dropping, or subjecting the device to strong impacts.
  • Overloading: Do not connect loads that exceed the specified current and voltage ratings of the controller's relays.
  • Storage: Store the controller in a dry, dust-free environment when not in use.

Troubleshooting

If you encounter any issues with your STC-3008 temperature controller, consider the following:

  • No Power: Check all power connections and ensure the power supply voltage matches the controller's requirements. Verify that the power outlet is functional.
  • Incorrect Temperature Readings: Ensure the temperature probes are correctly connected and fully inserted into their terminals. Check if the probes are damaged.
  • Outputs Not Activating: Verify that the set temperatures and differentials are correctly configured for heating or cooling mode. Check the wiring to the loads.
  • Overheating/Sparks/Malfunction: As a critical safety measure, if you observe any signs of overheating, sparks, or a malfunction, immediately disconnect the power supply to the unit and replace it. Do not attempt to repair a damaged unit.

Specifications

FeatureSpecification
ModelSTC-3008
Input Voltage OptionsDC 12V, DC 24V, AC 110-220V
Output TypeDual Relay Output
Relay Contact Current10A (max)
Temperature Probes2 x 1-meter probes included
Dimensions (L x W x H)86mm x 70mm x 27mm (35mm including clips)
Package Dimensions (L x W x H)10cm x 10cm x 10cm (approx.)
Package Weight0.168 kg (approx.)
Battery IncludedNo
CertificationCE
OriginMainland China

Warranty and Support

For specific warranty information, please refer to the terms and conditions provided by your retailer or contact the seller directly. Keep your purchase receipt as proof of purchase.

A more detailed user manual in PDF format is available for download: STC-3008 User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.