HeltecBMS HT-BCT50A

Contents

Heltec Single Channel 50A 5V Battery Capacity Tester User Manual

Model: HT-BCT50A

1. Introduction

This manual provides essential information for the safe and effective use of the Heltec Single Channel 50A 5V Battery Capacity Tester. This product is intended for professional use only. It is crucial to read and understand all instructions before operation, as incorrect settings or usage with lithium batteries can be extremely dangerous, potentially leading to explosion or fire. The manufacturer is not responsible for any direct or indirect consequences resulting from improper use.

Product features and accessories are subject to upgrades without prior notice.

2. Product Overview

The Heltec HT-BCT50A is a single-channel battery capacity tester designed for charging, discharging, and balancing various battery types, including Li-ion and LiFePo4. It features a clear display for monitoring parameters and a user-friendly interface for setting test conditions.

Heltec Single Channel 50A 5V Battery Capacity Tester
Heltec Single Channel 50A 5V Battery Capacity Tester (HT-BCT50A)
Heltec HT-BCT50A with included accessories
Product contents: HT-BCT50A tester, power cable, and battery connection cables.
Video demonstrating the basic setup and operation of the battery capacity tester.

3. Setup and Safety Warnings

Before connecting any battery, ensure the device is powered off. Always connect the battery correctly to avoid reverse polarity. Incorrect connection can damage the device or the battery, and poses a risk of fire or explosion.

Diagram showing correct and incorrect battery clamp connections
Operation Prompt: Please read instructions carefully. Incorrect setting may cause battery explosion and fire. Ensure correct polarity: Red for positive (+), Black for negative (-). Prohibit reverse connection.

Important Connection Guidelines:

  1. Both the large and small crocodile clamps must be clamped on the battery pole lugs.
  2. The contact area between the large crocodile clip and the pole ear should be large enough. It is prohibited to clip it onto screws, nickel plates, or wires, as this will cause abnormal interruption of the testing process.
  3. The small crocodile clip must be clamped at the bottom of the battery ear; otherwise, it may cause inaccurate capacity testing.

Device Components:

Labeled diagram of the HT-BCT50A tester showing power switch, display, control knob, buttons, and ports.
Product Appearance Function:
1. Power Switch: If power is cut off during test, data will not be saved.
2. Display Screens: Displays charging/discharging parameters and discharge curve.
3. Coding Switches: Rotate to adjust working mode, press to set parameters.
4. Start/Stop Button: Any operation in running state must be paused first.
5. Battery Positive Input: 1-2-3 pin through current, 4 pin voltage detection.
6. Battery Negative Input: 1-2-3 pin through current, 4 pin voltage detection.
7. Powerline Interface
8. Transmission Line Interface

General Safety Warnings:

  • It needs to be grounded to use, otherwise it may cause a slight leakage sensation.
  • Do not test batteries over 5V.
  • The radiator surface can reach high temperatures and is connected to the positive electrode of the battery. Prohibit short circuits and touching.
  • Testing must be conducted in a supervised, open environment, away from high-temperature, flammable, and explosive materials.

4. Operating Instructions

1. Initial Setup:

  1. Start up the device first, then securely clip the battery to the terminals.
  2. Press the setting knob to enter the settings page.
  3. Rotate the knob left and right to adjust parameters, then press to confirm.
  4. Set all parameters correctly and save before exiting.
Screenshot of the settings page on the HT-BCT50A tester
Settings page for configuring charge, discharge, and cycle parameters.

2. Parameter Settings for Different Modes:

Charging Mode:

  • Charging End Voltage: Set correctly and reasonably based on battery type:
    • Lithium Titanate: 2.7-2.8V
    • 18650/Ternary/Polymer: 4.1-4.2V
    • Lithium Iron Phosphate: 3.6-3.65V
  • Charging Current: Set to 10-20% of the cell capacity. It is recommended to set a current that minimizes cell heating.
  • Judging Full Current (Cutoff Current): When constant current charging switches to constant voltage charging, and the charging current drops below this value, the battery is considered fully charged. Recommended settings:
    • Batteries below 5Ah: 0.2A
    • Batteries 5-50Ah: 0.5A
    • Batteries above 50Ah: 0.8A

Discharge Mode:

  • Discharge End Voltage: Set correctly and reasonably based on battery type:
    • Lithium Titanate: 1.6-1.7V
    • 18650/Ternary/Polymer: 2.75-2.8V
    • Lithium Iron Phosphate: 2.4-2.5V
  • Discharge Current: Set to 10-50% of the cell capacity. It is recommended to set a current that minimizes cell heating.

Cycle Mode:

  • Charge and discharge mode parameters need to be set simultaneously.
  • Keep Voltage: The cut-off voltage of the last charge in cyclic mode can be the same as the cut-off voltage of the charge or discharge.
  • Resting Time: After the battery is fully charged or discharged (to allow the battery to cool down), usually set for 5 minutes.
  • Cycle: Maximum 5 times. Examples:
    • 1 time: Charge-Discharge-Charge
    • 2 times: Charge-Discharge-Charge-Discharge-Charge
    • 3 times: Charge-Discharge-Charge-Discharge-Charge-Discharge-Charge

Voltage Balancing Mode:

  • Discharge End Voltage: Set to the desired cell voltage for balancing. This value must be higher than 10mV above the battery voltage.
  • Discharge Current Setting Reference: Recommended to set between 0.5-10A. The smaller the cell capacity or voltage difference, the smaller the current setting should be.
  • End Current: Recommended to set to 0.01A.

3. Starting and Pausing Tests:

  1. Return to the home page.
  2. Rotate the setting button left or right to select the desired working mode.
  3. Press the Start/Stop button to begin the test.
  4. Press the Start/Stop button again to pause the test.
Screenshot of the home page on the HT-BCT50A tester showing current status and mode selection
Home page displaying current voltage, current, capacity, and mode selection options.

4. Viewing Test Results:

  1. After the test ends, the result page will automatically pop up.
  2. Press any button to stop the alarm sound.
  3. Record the results manually.
  4. Press the Start/Stop button again to view the results and curve of each step in turn.
Graph of test results on the HT-BCT50A tester
Test result graph showing voltage and current curves over time. Yellow numbers represent the voltage axis, yellow curve represents the voltage curve. Green numbers represent the current axis, green curve represents the current curve.

Interpretation of Results:

  • '1' indicates the first cycle, with AH/WH/min for charge and discharge respectively.
  • When battery performance is good, voltage and current curves should be relatively smooth.
  • Sharp rises or falls in voltage/current may indicate a pause during the test, excessively large charge/discharge current, or high internal resistance, suggesting the battery is near end-of-life.
  • If the test result is empty, and the working step was less than 2 minutes, data will not be recorded.

5. Specifications

ParameterValue
ModelHT-BCT50A5V
Charging Range0.3-5V / 0.3-50A Adj, CC-CV
Discharge Range0.3-5V / 0.3-50A Adj, CC
Work StepCharge/Discharge/Rest time/Cycle 9999 times
Auxiliary FunctionsVoltage balancing (CV Discharge)
Protective FunctionBattery overvoltage / Battery reverse connection / Battery disconnection / Fan not running
Calibration EquipmentV: Fluke 8845A, A: Gwinstek PCS-10001
AccuracyV ±0.1%, A ±0.1% (Accuracy guaranteed for one year from purchase date)
CoolingFans activate at 40°C, protected at 83°C (check and maintain regularly)
Working Environment0-40°C, air circulation, prevent heat accumulation
WarningForbidden to test batteries over 5V
PowerAC200-240V 50/60HZ (110V version available upon request)
Size and Weight167*165*240mm, 2.6Kg

6. Maintenance

  • Regularly check and maintain cooling fans to ensure proper operation and prevent overheating.
  • Keep the device in a clean, dry environment with good air circulation.
  • Avoid exposing the device to high temperatures, flammable, or explosive materials.
  • Use a well-grounded power socket to prevent electrical leakage or minor induction.

7. Troubleshooting

  • No data recorded: If the working step is less than 2 minutes, the data will not be recorded.
  • Abnormal test interruption: Ensure the contact area between the large crocodile clip and the battery pole ear is sufficient. Avoid clipping onto screws, nickel plates, or wires.
  • Inaccurate capacity testing: Ensure the small crocodile clip is clamped at the bottom of the battery ear.
  • Device not responding or data loss: Do not power off or switch working modes during operation. Any operation on the running machine must first press the pause key.
  • Feeling slight leakage: Ensure the device is properly grounded.
  • Battery explosion/fire: Always set charging and discharging parameters correctly and reasonably according to battery manufacturer specifications. This is critical for safety.

8. User Tips

  • Battery Connection: 99% of failures are due to poor contact between the battery clamp and the battery pole ear, bad contact, or too large charge/discharge current. Ensure a large contact area. Consider making your own battery clamps for optimal connection.
  • Battery Compatibility: Do not test batteries that are not rechargeable, have zero voltage, or show damaged bulges.
  • Voltage Limits: It is forbidden to test batteries over 5V. Doing so will void the warranty.
  • Heat Management: The radiator surface can get hot. Avoid touching it during operation and ensure good ventilation around the machine.

9. Warranty and Support

Warranty Policy:

The warranty service period is 1 year from the date of purchase.

The warranty is limited to normal use. Damage caused by human factors, self-disassembly, modification, repair, use not in accordance with instructions, or damage due to external force majeure factors are not covered by the free warranty.

Accessories such as test fixtures are consumables and are not covered by warranty.

Support:

For warranty service, please contact your dealer. If you cannot reach the dealer, you may contact the manufacturer directly via email or phone.

Please note that there are no after-sales service stations outside of China. If warranty service is needed internationally, the product must be sent to the manufacturer for free repair, but the customer is responsible for round-trip shipping costs.

This product is solely a tool, and its use is entirely at your discretion. The company refuses to accept any responsibility for its application beyond its intended purpose.

For more details, please consult customer service.

Heltec Energy - www.heltec-energy.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.