Erilles ZK-SMC01

Contents

SMC01 Single-axis Stepper Motor Controller User Manual

Model: ZK-SMC01 | Brand: Erilles

1. Introduction

This manual provides instructions for the Erilles ZK-SMC01 Single-axis Stepper Motor Controller. This device is designed for controlling stepper motors with features such as forward/reverse rotation, angle pulse speed control, and reverse connection protection. Please read this manual thoroughly before operation to ensure proper use and safety.

2. Safety Information

  • Quality guaranteed. Check before use. Use properly.
  • Keep away from fire, heat, and sharp items.
  • Keep small parts away from children under 3 years of age.
  • Do not disassemble the product.
  • ATTENTION: Not suitable for children under three years.

3. Product Overview

3.1 Key Features

  • Adjustable Delay
  • Speed Regulation
  • Angle Adjustment
  • Adjusting Distance
  • Forward/Reverse Rotation Control
  • Pulse/Direction Control
  • Auto/Manual Operation Modes
  • TTL Serial Communication
  • Reverse Connection Protection
Image showing key features of the stepper motor controller: Adjustable Delay, Speed Regulation, Angle Adjustment, Adjusting Distance.
Figure 1: Key Features of the ZK-SMC01 Controller

3.2 Controller Components

Front panel of the ZK-SMC01 Stepper Motor Controller showing buttons and indicators. Labels include: Forward rotation (CW button), Reverse rotation (CCW button), Forward rotation indicator (CW LED), Reverse rotation indicator (CCW LED), Encoder setting knob, and Run/pause button.
Figure 2: Front Panel Controls and Indicators

The front panel includes:

  • CW Button: Initiates forward rotation.
  • CCW Button: Initiates reverse rotation.
  • CW Indicator: Lights up when rotating forward.
  • CCW Indicator: Lights up when rotating in reverse.
  • Encoder Setting Knob: Used for adjusting parameters such as speed, angle, and delay.
  • RUN/STOP Button: Starts or pauses the motor operation.

4. Specifications

Attribute Value
Model Number ZK-SMC01 Stepper Motor Controller
Brand Name Erilles
Motor Type Stepper Motor
Power Supply DC 5-30V
Control Type Pulse / Direction
Communication TTL Serial Communication
Certification CE
Dimensions (approx.) 79mm (length) x 43mm (width) x 26mm (height) - Front Panel; 71mm (mounting length) x 39mm (mounting width)
Diagram showing the dimensions of the ZK-SMC01 Stepper Motor Controller. Front panel dimensions are 79mm length, 43mm width, 26mm height. Mounting dimensions are 71mm length and 39mm width.
Figure 3: ZK-SMC01 Controller Dimensions

5. Setup and Installation

Before connecting, ensure the power supply is disconnected. Refer to the wiring diagram below for correct connections.

Wiring diagram for the ZK-SMC01 Stepper Motor Controller. Terminals are labeled: GND (Connected to negative common terminal of driver), EN (Connected to driver enable terminal), DIR (Connected to driver direction end), PUL (Connected to driver pulse direction), DC+ and DC- (Connected to DC 5-30V power supply). Serial communication pins are +3.3V, TX, RX, GND. Also shows Public line, Stop signal, Reverse signal, Forward rotation signal, and Reserved signal points.
Figure 4: Wiring Diagram

5.1 Wiring Connections

  • DC+ and DC-: Connect to a DC 5-30V power supply. Ensure correct polarity. The controller features reverse connection protection.
  • GND: Connect to the negative common terminal of the stepper motor driver.
  • EN: Connect to the driver's enable terminal.
  • DIR: Connect to the driver's direction input.
  • PUL: Connect to the driver's pulse input.
  • Public Line: Connects to the common ground or positive voltage depending on the driver's input type (NPN/PNP).
  • Stop Signal: Input for an external stop signal.
  • Reverse Signal: Input for an external reverse rotation signal.
  • Forward Rotation Signal: Input for an external forward rotation signal.
  • Reserved Signal: Unused input.

5.2 Serial Communication

The controller supports TTL serial communication. The pins are:

  • +3.3V: Power output for serial communication.
  • TX: Transmit data.
  • RX: Receive data.
  • GND: Ground for serial communication.

A free matching plug cable is included for convenience (refer to Figure 5).

Top view of the ZK-SMC01 Stepper Motor Controller and the included free matching plug cable.
Figure 5: Controller with Matching Plug Cable

6. Operating Instructions

Once the controller is correctly wired and powered on, you can operate the stepper motor using the front panel controls.

6.1 Basic Operation

  1. Power On: Connect the DC 5-30V power supply. The display will light up.
  2. Start Motor: Press the RUN/STOP button to start the motor. The motor will operate according to the currently set parameters.
  3. Pause Motor: Press the RUN/STOP button again to pause the motor.
  4. Forward Rotation: Press the CW button to initiate forward rotation. The CW indicator will light up.
  5. Reverse Rotation: Press the CCW button to initiate reverse rotation. The CCW indicator will light up.

6.2 Parameter Adjustment

Use the Encoder Setting Knob to adjust various parameters such as speed, angle, and delay. The specific menu navigation and parameter settings will be displayed on the screen. Refer to the detailed PDF manual for advanced parameter configuration.

7. Maintenance

  • Keep the controller clean and free from dust and moisture.
  • Avoid exposing the device to extreme temperatures or direct sunlight.
  • Regularly check all wiring connections for security and integrity.
  • Do not attempt to repair the device yourself. Contact customer support for assistance.

8. Troubleshooting

  • Motor not responding:
    • Check power supply connections (DC 5-30V) and ensure correct polarity.
    • Verify all wiring to the stepper motor driver (GND, EN, DIR, PUL) is secure and correct according to the diagram.
    • Ensure the motor driver itself is powered and functioning correctly.
    • Check if the motor is paused; press RUN/STOP.
  • Incorrect rotation direction:
    • Verify the DIR connection to the driver.
    • Adjust direction settings using the encoder knob if available in the menu.
  • Unstable motor movement:
    • Check for loose connections.
    • Ensure the power supply is stable and within the specified voltage range.
    • Adjust speed and acceleration parameters using the encoder knob.

9. User Tips

No specific user tips were available from reviews or Q&A for this product at this time. Always ensure your stepper motor driver is compatible with pulse/direction control signals and that its enable pin is correctly configured for the ZK-SMC01 controller.

10. Warranty and Support

Your package includes one (1) ZK-SMC01 Stepper Motor Controller. For after-sales service or technical support, please contact the seller directly.

A detailed user manual in PDF format is available for further reference. You can access it via the following link: View User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.