Biurlink 16pin

Contents

Biurlink RCA Cable Adapter for Mazda Car Radio AUX

User Manual

Introduction

This manual provides detailed instructions for the installation and operation of your Biurlink RCA Cable Adapter. This adapter allows you to connect external audio devices to your compatible Mazda car radio, enabling audio streaming through the car's sound system.

Package Contents

Please verify that all items are present in your package:

  • 1 x RCA Cable Adapter (16-pin connector with red and white RCA plugs)
  • 1 x User Manual

Specifications

Condition 100% Brand New
Cable Length 34 cm (approximately 13.4 inches)
Socket Type RCA Socket (Red/White)
Connector Type 16-pin connector for car radio
Interface AV-Out
Material ABS
Voltage 5V
Item Weight 31g

Compatibility

This RCA Cable Adapter is designed for use with most AUX-enabled car stereos. Your car stereo must have an AUX function, typically accessible by selecting the correct input mode (e.g., 'AUX' or 'Bluetooth Aux socket').

Specifically compatible with the following Mazda models (2006 and newer):

  • Mazda 2 (2006 and up)
  • Mazda 3 (2006 and up)
  • Mazda 5 (2006 and up)
  • Mazda 6 (2006 and up)
  • Mazda MX5 (2006 and up)
  • Mazda RX8 (2006 and up)

It may also be compatible with other car brands such as Toyota, Honda, Volkswagen, AUDI, Benz, Suzuki, Nissan, Porsche, Ford, Fiat, Acura, BMW, Volvo, Skoda, Peugeot, Renault, Citroen, and Opel, provided they have a compatible 16-pin AUX input.

If you are unsure about compatibility, please consult your car's manual or contact the seller for assistance.

Setup and Installation

Follow these steps to install and set up your RCA Cable Adapter:

  1. Access Car Stereo: Carefully remove your car stereo from its dashboard slot to access the rear connections. Refer to your car's service manual for specific instructions on how to safely remove the stereo.
  2. Connect RCA Cable: Locate the appropriate 16-pin AUX input port on the back of your car stereo. Plug the 16-pin connector of the RCA cable adapter firmly into this port.
  3. Route Cable: Route the RCA plugs (red and white) to a convenient location in your car, such as the glove compartment or center console, where you can easily connect your audio device.
Close-up of the 16-pin connector and the cable wiring
Figure 1: Close-up of the 16-pin connector and cable wiring.
Side view of the RCA cable adapter, showing the 16-pin connector and RCA plugs
Figure 2: Side view of the RCA cable adapter, illustrating the 16-pin connector and RCA plugs.
Detailed close-up of the red and white RCA audio input connectors
Figure 3: Detailed view of the red and white RCA audio input connectors.

Operating Instructions

Once the cable is installed, follow these steps to stream audio:

  1. Power On Stereo: Turn on your car stereo.
  2. Select AUX Input: Set your car stereo to the AUX input mode. This is usually done by pressing a 'MODE' or 'AUX' button on your stereo, or selecting it from the on-screen menu.
  3. Connect Audio Device: Connect your smartphone, tablet, laptop, or other audio-enabled device to the red and white RCA plugs of the adapter using a compatible RCA to 3.5mm jack cable (not included).
  4. Play Music: Start playing music or audio from your connected device. The audio will now be transmitted through the RCA cable adapter to your car stereo, allowing you to enjoy it through your car's speakers.

Safety Precautions

Please observe the following safety precautions to ensure safe operation and prevent damage:

  • Approved Radio Supply: For safety, use this adapter only with a car radio that is approved for its power supply and specifications.
  • Road Safety: Do not operate or adjust the cable or connected devices while driving. Always prioritize road safety and focus on the road.
  • Liquid Exposure: Keep the adapter and its connections away from water, rain, or other liquids to prevent electrical damage and potential hazards.

Maintenance

This RCA cable adapter requires minimal maintenance. Keep the connectors clean and free from dust and debris. Store the cable in a dry environment when not in use. Avoid bending or crimping the cable excessively to prevent internal wire damage.

Troubleshooting

  • No Audio Output:
    • Ensure the 16-pin connector is securely plugged into the car stereo.
    • Verify that your car stereo is set to the correct AUX input mode.
    • Check that your audio device is playing music and its volume is turned up.
    • Ensure the RCA plugs are correctly connected to your audio device (red to right, white to left).
  • Poor Audio Quality:
    • Check all connections for looseness.
    • Ensure the audio source device is functioning correctly.
    • Avoid routing the cable near sources of electromagnetic interference.

If problems persist after following these steps, it is recommended to consult a professional car audio technician.

User Tips

  • Before purchasing, always confirm your car stereo has a compatible 16-pin AUX input. Some car models may require specific activation of the AUX input through the stereo's settings or a dealership.
  • Consider using a high-quality RCA to 3.5mm adapter cable for optimal audio transmission from your external device.
  • When installing, ensure the cable is routed in a way that does not interfere with vehicle operation or safety features.

Warranty and Support

For information regarding product warranty, technical support, or any other inquiries, please contact the seller directly or refer to the official Biurlink website for assistance.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.