ToolkitRC M6DAC PRO V2 Dual Channel Smart Lipo Battery Charger Discharger User Manual
Introduction
Thank you for purchasing the ToolkitRC M6DAC Pro/V2 dual balance charger. Please read this manual carefully before use to ensure optimal performance and safety.
Safety Instructions
Important Safety Information
- M6DAC Pro/V2 allows input voltage of 7-28V or AC 100-240V. Please ensure that the power supply voltage is in line with this range. Pay attention to the positive and negative polarities of the power supply when connecting.
- Do not use this product in a hot area or near a heat source. Do not use this product in a damp, flammable or explosive gas environment.
- Only use this product while under direct supervision. Do not leave charging batteries unattended.
- When not using this product, please unplug the input power in time.
- When using the charging function, please set the current matching with the battery. Do not set excessive current charging, so as not to damage the battery.
Product Layout
The ToolkitRC M6DAC Pro/V2 features a compact design with a smart 2.8" IPS LCD display and intuitive controls.

Front view of the M6DAC PRO V2 charger, showing the display, Exit/CH key, and scroll wheel.

Rear view of the M6DAC PRO V2 charger, highlighting the AC input, DC input, and USB-C output ports.
Controls and Ports:
- Display: Smart 2.8" IPS LCD display.
- Exit/CH Key: Used to exit menus or switch channels.
- Scroll Wheel: For navigation (left/right turn) and selection (press OK).
- Balance Port * 2: For connecting battery balance leads.
- Temp. Sensor Port: Type: DS18B20.
- Main Port * 2: For connecting main battery leads.
- States LED * 2: Indicate operational status.
- AC Input: For AC power supply (100-240V).
- DC Input: For DC power supply (7-28V).
- USB-C Output: For 65W fast charging of mobile devices.
- Cooling Fan: Automated fan speed for heat dissipation.
- Wireless Charging: (PRO version only) For compatible mobile devices.
Setup
Follow these steps to quickly set up and start using your M6DAC Pro/V2 charger.
- Connect Power: Connect a 7-28V DC power supply or an AC 100-240V power supply to the input port on the back of the M6DAC Pro/V2.
- Initial Boot: The display will show the boot logo for 2 seconds, accompanied by a boot sound.
- Main Interface: After booting, the display will enter the main interface, showing current status.

The main interface in standby mode, displaying 0.00V for both channels.

Connecting the AC power cable to the charger's input port.
Basic Navigation:
- Switch Channels: Short press the [Exit/CH] key to switch the cursor between the left and right channels.
- Internal Resistance Test: Press and hold [Exit/CH] to test the internal resistance of the selected channel.
- Switch Pages: Scroll the [Scroll Wheel] to switch between different pages in the corresponding channel.
- Confirm/Select: Short press [OK] (by pressing the scroll wheel) to select a charging task or confirm an action.
- System Settings: Press and hold [OK] when both channels are idle to enter the system settings interface.
- Exit/Return: Press [Exit] to end modifications or return to the previous interface.
Operating Instructions
Charge and Discharge Settings
Short press [OK] on the main interface to enter the charging function settings.
1. Battery Type
Move the cursor to [Battery Type] and press [OK] to modify the battery type. The charger supports charging and discharging of 7 types of batteries: LiPo, LiHV, LiFe, Lion, LTO, NiMh, and PB. Power supply and smart battery options are also available.
- LiPo: Lithium polymer battery, nominal 3.70V, fully charged 4.20V.
- LiHV: High-voltage lithium battery, nominal 3.85V, fully charged 4.35V.
- LiFe: Iron-lithium battery, nominal 3.30V, fully charged 3.60V.
- Lion: Lithium-ion battery, nominal 3.60V, fully charged 4.10V.
- LTO: Lithium titanate battery, nominal 2.40V, fully charged 2.70V.
- NiMh: Nickel-metal hydride battery, nominal 1.20V.
- PB: Lead-acid battery, nominal 2.00V.
2. Number of Cells
Move the cursor to [Battery cell Number] and press [OK] to modify the number of battery cells (1S to 6S). When set to [Auto], the charger automatically recognizes the number of connected battery cells based on voltage.
3. Mode
Move the cursor to [Mode] and press [OK] to select the working mode:
- Charge: Standard charging.
- Discharge: Standard discharging.
- Storage: Charges or discharges the battery to a safe storage voltage.
- Destroy: Completely discharges the battery for disposal.
4. Discharge Mode
When selecting Discharge, Storage, or Cycle mode, the battery setting interface will show discharge mode options:
- Inter (Internal) Mode: Discharges through internal heat consumption, max 3.0A@15W.
- Recycle Mode: Recovers electrical energy from the discharging battery to the input battery (requires input type to be 'battery' in settings).
- Bridge Mode: Dissipates electrical energy through an external power resistor. Connect the resistor to another channel. Recommended power resistor: 2-5Ω, 100-500W. Note: Input power supply requires an adapter.

Diagram showing the setup for bridge discharge mode, connecting a battery to one channel and a resistor to another.
5. Input MaxVoltage
When Recycle discharge mode is selected, set the [Input MaxVol]. If the input voltage reaches this value during discharge, the discharge will stop.
6. End Voltage (TVC)
Modify the end voltage of the single battery. In charging mode, this is the charging cut-off voltage (±50mV of full voltage). In discharge mode, it's the discharge cut-off voltage. Adjust in steps of 0.01V.
7. Current Setting
Move the cursor to [Charge Current] or [Discharge Current] and press [OK] to adjust. Rotate the [Scroll Wheel] to change the value in 0.1A steps. The charger supports up to 16.0A. In synchronous mode, it supports a maximum of 28A.
8. NiMH Setting (PeakV)
For NiMh batteries, set the negative pressure value (3mV-15mV) when the battery is fully charged. PeakV refers to the voltage drop of each cell when the nickel-metal hydride battery is fully charged.
9. Cycle Setting
For NiMh batteries, when Cycle mode is selected, set the number of cycles (2-12) and rest time (2-10 minutes). The charger will follow a pattern of discharging then charging.
10. Power Mode Setting
When the battery type is 'Power', the settings are limited to output voltage (1V-28V) and maximum current (0.5A-16A).
11. Smart Battery
For 'Smart Battery' type, settings include drone model (e.g., Mavic2, Phantom) and maximum current.
12. Synchronous Mode
When the synchronization function is enabled in system settings, both channels can charge the same battery with a total current of 28A.

The M6DAC PRO V2 set up for synchronous charging, utilizing both channels for a single battery.
Charge and Discharge Work
When charging or discharging begins, the charger enters the working interface, displaying real-time information.

The charger's display during active charging, showing voltage, current, and other parameters.

The charger's display showing internal resistance values for each cell during charging.
Rotate the [Scroll Wheel] to switch between bottom status information and internal resistance voltage values. Short press [OK] to dynamically set the working current or stop the process.
Display Content Description:
- 24.00V: Input power supply voltage
- 20.0Wh: Total power consumption of input power
- 45.0°C: Charger internal temperature
- QC: Charge protocol
- 12.0V: USB-C output voltage
- 2.0A: USB-C output current
- 25.21V: First channel main port voltage
- 20.00A: First channel main port current
- 099:00: First channel working time
- 888mAh: Cumulative capacity of the first channel
- Green/Red Indicators: Constant voltage sign (C), Constant current sign (I), Power limit (P), Input limit (I), Maximum current (C), Activate charging (A), Main port voltage or single cell voltage is full (F).
- 4.205V: 1st battery voltage
- 4.200V: 4th battery voltage (this cell is in balance management)
- -.--V: No battery connected
- Charging: Indicates the current charging status.
- Lipo 6S: The current rechargeable battery type and battery number.
- 4.20V/2.00A: Current battery end voltage and charging current.
- When charging and discharging, please directly supervise throughout the process to deal with any abnormality in time. Do not leave charging or discharging batteries unattended.
- When charging and discharging lithium batteries, only connecting to the main port will not perform balance management. Connect the balance lead for automatic balance management.
- After charging, unplug the battery and connect a new one. If continuous work mode is selected, the device will automatically continue charging/discharging with the set mode. Ensure consistent battery types and capacities when using fixed cell numbers.
Maintenance
1. Firmware Upgrade
Connect the M6DAC Pro/V2 to a computer using the USB cable. The computer will recognize a USB disk named "Toolkit". Download the upgrade file (app.upg) from the official website, copy it to the USB disk, and overwrite previous files to upgrade the firmware.
2. USB-C 65W Output
The USB interface can output 65W to charge mobile devices, supporting fast charge protocols including PD3.0/PD2.0/PPS/QC4/QC3.0/QC2.0/AFC/FCP/SCP/PE2.0/PE1.1/SFCP/VOOC.
3. Automatically Continue to Charge and Discharge
When a battery is fully charged, unplug it for 2 seconds, then connect the next battery. The device will continue to charge and discharge automatically if this function (Continuous work mode) is enabled in the menu.
4. Fan Level
The fan speed is automated: half-speed airflow when internal temperature exceeds 45°C to reduce noise, and full-speed airflow when temperature exceeds 53°C to enhance heat dissipation.
5. Manual Voltage Calibration
In the shutdown state, press and hold the [Scroll Wheel] while connecting the power supply. The system will enter the manual voltage calibration function. Measure the actual voltage of each battery with a voltmeter, then adjust the displayed voltage to match. After calibration, move the cursor to save, short press once, and a beep will confirm success. Log out or shut down to exit.
6. Fully Charged
When a lithium battery is charged, it will prompt "Fast charging has ended". If the battery is not removed, constant voltage trickle charging will automatically continue to fully charge the battery.
7. Wireless Charging (PRO version only)
The M6DAC Pro version includes a built-in wireless charging module that automatically adapts and charges compatible mobile devices when placed on top. Charging power is 10W.

A smartphone wirelessly charging on the M6DAC PRO V2 charger (PRO version feature).
8. Bridge Discharging
In bridge discharging mode, the input port is connected to the power supply. The discharged battery is connected to any channel, and a power resistor is connected to another channel. This allows the battery's electrical energy to be dissipated through the resistor as heat. The total discharge power P equals the voltage across the resistor multiplied by the current through the resistor (P = V resistor * I resistor). Recommended power resistor selection: 2-5Ω and 100-500W power.
Troubleshooting
- Charger not powering on: Ensure the power supply voltage is within the 7-28V DC or 100-240V AC range and connections are secure.
- Battery not recognized: Check if the battery type and cell count are correctly set in the charger's menu. Over-discharged or over-charged batteries may not be recognized automatically; try manually setting the cell count.
- Charging issues (e.g., slow charging, no charge): Verify that the charging current is appropriate for the battery's capacity (1-2C rate). Ensure balance leads are connected for lithium batteries to enable balance management.
- Overheating during charging: The charger has automated fan speed control. Ensure the fan vents are not obstructed. If the charger or battery becomes excessively hot, stop the process immediately and allow it to cool.
- Wireless charging not working: Ensure you have the PRO version of the M6DAC. Check that the mobile device is placed correctly on the wireless charging pad and is compatible with wireless charging.
- Display issues: If the display is unresponsive or shows errors, try restarting the charger. If issues persist, consider a firmware upgrade.
User Tips
- Monitor Temperature: While the charger has built-in cooling, it's good practice to monitor the temperature of the charger and batteries, especially during high-power operations. The wireless charging plate may get warm during use.
- Cables Not Included: Be aware that charging cables (e.g., EC5, EC3) are typically not included with the charger and may need to be purchased separately.
- Compact Size: The M6DAC PRO V2 is noted for its compact size, making it convenient for transport and use in various setups.
- Dual Chemistry Charging: The M6DAC PRO V2 supports charging two batteries of different chemistries (e.g., LiPo on Channel 1 and NiMH on Channel 2) simultaneously.
Specifications
| Category | Item | Value |
|---|---|---|
| Input | Input Voltage | DC 7-28V@MAX30A, AC 100-240V@MAX200W (V2), AC 100-240V@MAX300W (PRO) |
| Battery Type | Supported Types | LiPo, LiHV, LiFe, Lion, LTO@1-6S; NiMh@1-16S; Pb@1-10S |
| Balance Current | Balance Current | 1000mA @2-6S |
| Accuracy | Voltage Accuracy | <0.005V |
| Charging Power | Asynchronous | 0.1-16A@400W *2 |
| Synchronous | 0.1-28A@700W | |
| Discharging Power | Recycle Mode | 0.1-16A@400W *2 |
| Bridge Mode | 0.1-16A@400W | |
| Normal Mode | 0.1-3A@15W *2 | |
| USB-C | Output | 65W@20V@3.25A (upgrade) |
| Protocol | Supported Protocols | PD, QC, AFC, FCP, SCP, PE, SFCP, VOOC |
| Wireless Charging | Power | 10W (Only Pro) |
| Battery Voltage | Range | 1.0V-5.0V @1-6S |
| Battery Internal Resistance | Range | 1-100mR @1-6S |
| Display | Type | IPS 2.8 inch 320*280 resolution |
| Product | Size | 116mm*112mm*63mm |
| Weight | 600g/Pro, 570g/V2 | |
| Individual Packing | Size | 164mm*135mm*68mm |
| Weight | 730g/Pro, 700g/V2 |
Warranty and Support
For detailed guides, troubleshooting, and warranty information, please refer to the official ToolkitRC website or the comprehensive user manual PDF available at ToolkitRC M6DAC Pro/V2 User Manual (PDF). You can also visit www.toolkitrc.com for news, information, and firmware updates.