1. Introduction
Thank you for choosing the BEISHI Full Motion TV Wall Mount. This bracket is designed to securely hold your 26-55 inch flat-panel television, offering versatile viewing angles with its swivel, tilt, and extension capabilities. Please read this manual thoroughly before installation to ensure safe and correct setup.
2. Safety Information
- Read all instructions: Ensure you understand all instructions and warnings before installation.
- Wall Type: This mount is intended for installation on solid concrete walls, brick walls, or wood stud walls. Do not install on drywall alone.
- Weight Capacity: Do not exceed the maximum load weight of 35kg (77lbs).
- TV Size: Ensure your TV size is within the recommended range of 26-55 inches.
- VESA Compatibility: Verify your TV's VESA pattern matches the mount's compatibility (100x100mm to 400x400mm).
- Professional Installation: If you are unsure about the installation process, consult a qualified professional.
- Check Fasteners: Periodically check all screws and connections to ensure they are secure.
3. Package Contents
Please check that all components are present and undamaged before proceeding with installation.
- Telescopic Rotating Bracket (Main Assembly)
- Screws for Wall Mounting:
- M8x50mm (x4)
- 12x60mm (x4)
- Screws for TV Attachment:
- M4x25mm (x4)
- M6x25mm (x4)
- M8x25mm (x4)
- Washers: D5, D6 (quantities may vary, typically 4 each)
- Expansion Tubes (Wall Anchors)
Tools Required (Not Included): Drill, Screwdriver, Wrench, Hammer, Level.
4. Specifications
| Feature | Specification |
|---|---|
| Brand Name | BEISHI |
| Screen Size Suitable | 26-55 inches |
| Maximum Load Weight | 35kg (77lbs) |
| Standard VESA | 100x100, 200x100, 200x200, 300x200, 300x300, 400x300, 400x400mm |
| Distance to Wall | 7.5cm - 58cm (2.95in - 22.83in) |
| Adjustment | Tilted (-3° to +15°), Swivel, Level (+/- 3°) |
| Installation | Wall Mounting |
| Hign-concerned Chemical | None |
| Package | Yes |
| Origin | Mainland China |
5. Setup and Installation
Watch the official installation video for a visual guide:
Step-by-Step Installation:
-
Step 1: Prepare the Wall
Determine the desired installation height for your TV. Use a level to mark the drilling points on the wall for the bracket base. Ensure the top and bottom circular holes are used for screw positioning. Drill holes at the marked locations. The drilling depth should correspond to the size marked on the expansion tube surface. Insert the expansion tubes into the drilled holes.
Figure 5: Mark and drill holes, then insert expansion tubes into the wall. -
Step 2: Fix Bracket to Wall
Align the main bracket body with the drilled holes. Use the provided self-tapping screws (M8x50mm or 12x60mm, depending on your wall type) to securely fix the bracket to the wall. Ensure all screws are tightened appropriately.
Figure 6: The main bracket assembly securely mounted to the wall. -
Step 3: Attach TV Plate to TV
Select the appropriate screws (M4x25mm, M6x25mm, or M8x25mm) and small washers that fit your TV's VESA mounting holes. Attach the TV plate (hanging hooks) to the back of your television. Ensure the plate is centered and securely fastened.
Figure 7: The TV plate (hanging hooks) attached to the rear of the television. -
Step 4: Hang TV and Secure
Carefully lift the TV (with the attached plate) and hook it onto the hanging board of the wall mount. Once the TV is securely hanging, tighten the safety screws at the bottom of the hooks to prevent accidental dislodgement.
-
Cable Management
Install the support arm cable covers and organize all cables for a neat and tidy appearance.
6. Operation
This full motion TV mount offers several adjustment options to optimize your viewing experience:
- Extension/Retraction: The mount can extend up to 58cm (22.83in) from the wall and retract to 7.5cm (2.95in). Gently pull or push the TV to adjust the distance.
- Swivel: The articulating arm allows you to swivel the TV left or right to achieve the perfect viewing angle from different positions in the room.
- Tilt: The TV can be tilted from -3 degrees to +15 degrees to reduce glare and improve viewing comfort. Loosen the tilt adjustment screws on the TV plate, adjust to the desired angle, and then re-tighten the screws.
- Level Adjustment: The mount features a +/- 3 degree level adjustment to ensure your TV is perfectly horizontal after installation.
7. Maintenance
To ensure the longevity and safe operation of your TV wall mount, follow these simple maintenance guidelines:
- Cleaning: Wipe the mount with a soft, dry cloth to remove dust. Avoid using abrasive cleaners or solvents.
- Check Connections: Periodically (e.g., every 6 months) inspect all screws and bolts to ensure they remain tight and secure. Re-tighten if necessary.
- Inspect for Damage: Regularly check the mount for any signs of wear, corrosion, or damage. If any issues are found, discontinue use and contact customer support.
8. Troubleshooting
- TV is not level: Use the built-in level adjustment feature to fine-tune the horizontal position of your TV.
- Mount feels loose: Re-check all wall mounting screws and TV attachment screws. Ensure they are tightened securely. If the issue persists, consult a professional.
- Difficulty adjusting movement: Ensure no cables are snagged or obstructing movement. Check that all pivot points are free from debris.
9. User Tips
- Verify Wall Type: Always double-check your wall type (wood stud, concrete, brick) before drilling and use the appropriate anchors and screws.
- Measure VESA: Before purchasing or installing, measure the VESA pattern on the back of your TV to ensure compatibility with the mount.
- Two-Person Installation: For safety, especially when lifting and hanging the TV, it is highly recommended to have two people for the installation process.
10. Warranty and Support
For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.
For a comprehensive guide and additional details, please refer to the official user manual PDF: User Manual (PDF)