1. Introduction
This manual provides essential information for the installation, operation, and maintenance of your new Adjustable Rear Suspension Tie Bar Link Control Arm. This component is designed as a replacement and repair part for the rear suspension system of compatible Ford Focus Mk2, KUGA, and Mazda vehicles. Proper installation and regular maintenance are crucial for vehicle safety and performance.
2. Safety & Warnings
Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord (if applicable) out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
- Handle with care to avoid cuts or injuries.
- Always use appropriate personal protective equipment (PPE) such as safety glasses and gloves during installation.
- Ensure the vehicle is securely supported on jack stands on a level surface before working underneath it. Never rely solely on a jack.
3. Package Contents
Please check the package carefully upon receipt to ensure all components are present and undamaged.
- Main part: Adjustable Rear Suspension Tie Bar Link Control Arm(s)
- Accessories (e.g., hexagonal nut for adjustment)
- Hardware (e.g., threaded ends)


4. Setup (Installation)
4.1. Pre-Installation Check (Must Read)
- Verify OE Number: Confirm the Original Equipment (OE) number of this part (BV615K743AA or 98AG5K743AF) is 100% identical to your original broken part. If the OE Number is correct, continue installation. If the OE Number is wrong, DO NOT install; contact the seller immediately.
- Check Package Contents: Ensure all main parts, accessories, and hardware are present as listed in Section 3.
- Confirm Vehicle Match: Verify that the part is suitable for your specific vehicle model, year, and the intended installation position (e.g., rear left or rear right).
4.2. General Installation Steps
Professional installation is highly recommended for suspension components. Improper installation can lead to serious safety hazards and vehicle damage.
- Prepare Vehicle: Park the vehicle on a flat, level surface. Engage the parking brake. Loosen the lug nuts on the wheel(s) corresponding to the control arm to be replaced.
- Lift and Secure Vehicle: Safely raise the vehicle using a hydraulic jack and secure it firmly on jack stands. Ensure the vehicle is stable before proceeding. Remove the wheel(s).
- Locate and Remove Old Part: Identify the existing rear suspension tie bar link control arm. Note its orientation and how it is connected. Loosen and remove the mounting bolts securing the old control arm to the chassis and the suspension knuckle. Carefully remove the old control arm.
- Compare Parts: Place the new control arm next to the old one. Compare their lengths, mounting points, and overall design to ensure they are identical. If adjustable, ensure the new arm is set to approximately the same length as the old one before installation.
- Install New Part: Position the new control arm into place. Insert the mounting bolts through the appropriate holes. Hand-tighten the bolts initially. Do not fully tighten them yet.
- Final Tightening: Once the vehicle is at ride height (or as specified by the vehicle manufacturer for suspension component tightening), fully tighten all mounting bolts to the vehicle manufacturer's specified torque values. Refer to your vehicle's service manual for exact torque specifications.
- Reassemble: Reinstall the wheel(s) and hand-tighten the lug nuts. Lower the vehicle to the ground. Torque the lug nuts to the vehicle manufacturer's specifications.
- Wheel Alignment: After replacing any suspension component, a professional wheel alignment is highly recommended to ensure proper handling, tire wear, and vehicle safety.
5. Operating (Adjustment)
This control arm is adjustable, meaning its length can be altered. This adjustment is primarily used to fine-tune wheel alignment parameters, such as camber or toe, depending on the vehicle's suspension design. Adjustments should only be performed by a qualified automotive technician using specialized alignment equipment. Incorrect adjustments can severely affect vehicle handling, tire wear, and safety.
6. Maintenance
Regular inspection of suspension components is vital for vehicle safety and longevity.
- Periodic Inspection: During routine vehicle maintenance (e.g., oil changes, tire rotations), visually inspect the control arms for signs of wear, damage, or corrosion. Check the rubber bushings at each end for cracks, tears, or excessive play.
- Check Fasteners: Ensure all mounting bolts are tight and secure. Re-torque if necessary according to vehicle manufacturer specifications.
- Cleanliness: Keep the suspension area free from excessive dirt, mud, and road salt, which can accelerate corrosion.
7. Troubleshooting
If you experience any issues after installation, consider the following:
- Unusual Noises (clunking, squeaking): This could indicate loose mounting bolts, worn bushings, or improper installation. Re-check all fasteners and inspect bushings.
- Poor Handling or Uneven Tire Wear: This is often a sign of incorrect wheel alignment. A professional alignment is crucial after suspension work.
- Vibration: Can be caused by loose components or other suspension issues.
If problems persist, consult a qualified automotive technician for diagnosis and repair.
8. Specifications
| Feature | Detail |
|---|---|
| Product Name | Adjustable Rear Suspension Tie Bar Link Control Arm |
| OE Numbers | BV615K743AA, 98AG5K743AF |
| Fitment | Ford Focus Mk2, KUGA, Mazda (Verify with OE number) |
| Function | Replacement & repair of vehicle rear suspension parts |
| Adjustability | Length adjustable for alignment purposes |
| Material | Not specified (typically high-strength steel or aluminum) |
| Silent Block Sizes | Not specified |
9. User Tips
- Always Double-Check OE Numbers: The most critical step for ensuring compatibility is to match the OE number on your original part with the OE numbers provided for this product. Vehicle models can have variations, so relying solely on make/model/year might lead to incorrect fitment.
- Professional Installation is Key: For safety and optimal performance, especially with adjustable suspension components, professional installation and subsequent wheel alignment are strongly recommended.
10. Frequently Asked Questions (FAQ)
- Q: Will this part fit my 2015 Ford Focus?
- A: This part is specified for Ford Focus Mk2. To ensure compatibility for your 2015 model, please compare the OE number (BV615K743AA or 98AG5K743AF) with the OE number on your original part. If they match, it should fit.
- Q: Can you provide the inner and outer dimensions of the silent blocks (bushings)?
- A: The specific dimensions for the silent blocks are not provided in the product documentation.
11. Warranty & Support
For any questions regarding warranty coverage, technical support, or product issues, please contact your seller directly. Keep your purchase receipt or order details handy for faster service.
A user manual in PDF format may also be available for download: View User Manual (PDF)