ggbingo NL10

Contents

GGbingo LED Night Light Desk Lamp

Model: NL10

Brand: GGbingo

1. Safety & Warnings

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.

Battery Warning

Swallowing can lead to chemical burns, perforation of soft tissue, and death. Severe burns can occur within 2 hours of ingestion. Seek medical attention immediately.

2. Setup

2.1 Package Contents

  • 1 x GGbingo LED Night Light (Bulb)
  • 1 x User Manual
  • 1 x Remote Control (for applicable models)
  • 2 x Magnetic Mounts with 3M Adhesive

2.2 Charging the Lamp

Before first use, fully charge the lamp. The lamp features a built-in large capacity lithium battery.

  1. Locate the USB charging port on the lamp.
  2. Connect the lamp to a USB power source (e.g., charging head, notebook, power bank) using a compatible USB cable.
  3. Charging time is approximately 3.5 hours.
Lamp charging from various USB sources

Figure 1: Charging the lamp from different USB sources.

2.3 Installation

The lamp features magnetic adsorption for easy installation and removal.

  1. Clean the surface where you intend to mount the lamp.
  2. Peel off the protective film from one side of the 3M adhesive.
  3. Attach the 3M adhesive to the back of the magnetic mount.
  4. Peel off the protective film from the other side of the 3M adhesive.
  5. Attach the magnetic mount to your desired surface (e.g., under a cabinet, on a wall).
  6. Align the lamp with the magnetic mount and allow it to snap into place.

The lamp can be easily removed from the magnetic mount at any time for handheld use or recharging.

Step-by-step installation guide for the magnetic lamp

Figure 2: Easy installation steps using magnetic mounts.

3. Operating Instructions

3.1 Power On/Off

  • Touch Control: Briefly touch the power button on the lamp to turn it on or off.
  • Remote Control: Press the power button on the remote control to turn the lamp on or off.

3.2 Brightness Adjustment

  • Touch Control: Long press the power button on the lamp for stepless dimming. Release when desired brightness is reached.
  • Remote Control: Use the '+' button to increase brightness and the '-' button to decrease brightness. There are 10 levels of brightness adjustment.

3.3 Color Temperature Adjustment

  • Touch Control: Briefly touch the power button repeatedly to cycle through 3 color temperatures: Warm Yellow, Warm White, and White.
  • Remote Control: Press the 'M' button on the remote control to cycle through the 3 color temperatures.
Diagram showing 3 color temperatures and 10 brightness levels

Figure 3: Available color temperatures and brightness levels.

3.4 Remote Control Functions

The remote control provides convenient access to all lamp functions:

  • Power Button: Turn the lamp On/Off.
  • '+' Button: Increase brightness.
  • '-' Button: Decrease brightness.
  • 'M' Button: Change color temperature (Warm Yellow, Warm White, White).
  • '10' Button: Set a 10-minute timer.
  • '30' Button: Set a 30-minute timer.
Lamp installed with remote control in hand

Figure 4: Operating the lamp with the remote control.

3.5 Handheld & Flashlight Function

The lamp can be easily detached from its magnetic mount and used as a portable handheld light or a flashlight.

Lamp used as a portable handheld flashlight

Figure 5: Lamp used as a portable handheld light.

3.6 Product Demonstration Video

Video 1: Product features and usage demonstration.

4. Maintenance

To ensure optimal performance and longevity of your GGbingo LED Night Light:

  • Wipe the lamp surface with a soft, dry cloth to remove dust.
  • Do not use abrasive cleaners or solvents, as they may damage the finish.
  • Keep the lamp away from excessive heat and direct sunlight.

5. Troubleshooting

  • Lamp not turning on: Ensure the lamp is fully charged. Connect it to a USB power source and allow it to charge for at least 30 minutes before trying again.
  • Remote control not working: Ensure there are no obstructions between the remote and the lamp. Check if the remote control's battery needs replacement (if applicable).
  • Dim light: The battery might be low. Recharge the lamp.

6. Specifications

FeatureSpecification
Product NameNight Light
ModelNL10 (2134)
LED Quantity20 LEDs
Power4W (0-5W)
Lithium Battery5V, ~800mAh
Nominal Voltage4.5V
Voltage5V
Dimensions26 x 2.2 x 2 cm
Charging Time3.5 hours
Working Time (Low Brightness)24 hours
Working Time (Medium Brightness)8 hours
Working Time (High Brightness)4 hours
Light ColorWarm White, White, Warm Yellow
Luminous Flux249-2000 lm
Body MaterialABS Plastic
Switch TypeTouch On/Off Switch
CertificationsRoHs, LVD, CE

7. User Tips

  • Use the timer function (10 or 30 minutes) for bedtime reading to conserve battery.
  • Adjust the color temperature to suit your activity: cooler white for focused work, warmer yellow for relaxation.
  • Take advantage of the magnetic attachment to easily move the lamp between different locations like closets, under cabinets, or as a portable light.
  • The soft, flicker-free light is designed for eye protection, making it suitable for extended reading or study sessions.

8. Warranty & Support

This product comes with a 12-month warranty from the date of purchase.

Manufacturer Information

  • Manufacturer: Foshan Shunde Smida Electric Appliance Co., Ltd.
  • Contact No: +8615361791976
  • Email: PalijAmarar@outlook.com
  • Address: No.1 Yongyong Road, Gangkou Road, Leliu Town, Shunde District, Foshan City, Guangdong Province.

EU Authorized Representative

  • Name: Apex CE Specialists GmbH
  • Email: Info@apex-ce.com
  • Address: Habichtweg 1 41468 Neuss Germany

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.