1. Introduction
This manual provides detailed instructions for the assembly, operation, and maintenance of your Wishiot 4WD RC Car Chassis Electric Set. Please read this manual thoroughly before beginning assembly to ensure correct setup and optimal performance.
This set allows you to construct a functional 4WD RC car chassis using building blocks, integrating electric motors, a receiver, and a battery box for remote control operation.
2. Package Contents
Before starting assembly, please verify that all components are present. Refer to the parts list below and the visual guide.

Figure 2.1: All components included in the set.

Figure 2.2: Electronic components: motors, receiver, battery box, and remote control.
2.1. Parts List (Summary)
The set includes various building blocks, axles, gears, wheels, and electronic components. A detailed visual parts list is available in the official PDF manual on pages 2-4.
- Assorted Building Blocks (beams, pins, connectors)
- Axles (various lengths)
- Gears (various sizes)
- 4 x Wheels with Tires
- 1 x L-Motor
- 1 x Servo Motor
- 1 x Battery Box
- 1 x RC Receiver
- 1 x Remote Control
- Connecting Cables
- Small Screwdriver (for battery compartment)
3. Setup and Assembly
Assembly of this building block set requires careful attention to detail. For the most comprehensive visual guide, please refer to the official PDF user manual: Download PDF Manual.
3.1. General Assembly Steps
The assembly process involves building the chassis frame, integrating the drivetrain components (differentials, axles, gears), mounting the motors, battery box, and receiver, and finally attaching the wheels.
- Differential Assembly (Steps 1-8): Begin by assembling the front and rear differential units using small blocks, gears, and axles.
- Chassis Frame Construction (Steps 9-14): Build the main chassis frame, incorporating the steering rack and connecting the front differential.
- Rear Axle and Drivetrain (Steps 15-22): Assemble the rear axle, connect it to the chassis, and integrate the rear differential and drive shaft.
- Motor and Electronics Mounting (Steps 23-29): Securely attach the L-Motor and Servo Motor to the chassis. Mount the battery box and RC receiver, ensuring all connections are accessible.
- Final Touches (Steps 30-31): Complete any remaining structural elements and double-check all connections.

Figure 3.1: Rendered view of the assembled chassis.
3.2. Battery Installation
The set requires user-supplied batteries for the Battery Box and the Remote Control.
- Battery Box: Open the battery compartment on the Battery Box (usually with a small screwdriver). Insert the required number and type of batteries (e.g., AA or AAA, check markings on the box for specifics) ensuring correct polarity (+/-). Close the compartment securely.
- Remote Control: Open the battery compartment on the Remote Control. Insert the required batteries (e.g., AAA) ensuring correct polarity. Close the compartment.
Warning: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
3.3. Wiring Connections
Connect the L-Motor and Servo Motor to the RC Receiver using the provided cables. Ensure the cables are routed neatly and do not interfere with moving parts. Connect the Battery Box to the RC Receiver to provide power.
4. Operating Instructions
4.1. Power On/Off
- Ensure batteries are correctly installed in both the Battery Box and Remote Control.
- Turn on the power switch on the Battery Box (if present).
- Turn on the power switch on the Remote Control.
- The RC Receiver and Remote Control should automatically pair. If not, refer to the troubleshooting section or the PDF manual for specific pairing instructions.
4.2. Remote Control Functions

Figure 4.1: Remote Control Unit.
The remote control typically features two joysticks or control levers:
- Left Joystick/Lever: Controls forward and backward movement (throttle).
- Right Joystick/Lever: Controls left and right steering.
- Additional Buttons/Switches: May be present for fine-tuning steering, speed modes, or controlling additional functions if your specific build includes them (e.g., spray function if equipped).
4.3. Driving the RC Car
- Place the assembled RC car on a flat, clear surface.
- Gently push the throttle joystick forward to move the car forward, and pull it back to move backward.
- Use the steering joystick to turn the car left or right.
- Practice in an open area to get accustomed to the controls.
4.4. Spray Function (If Applicable)
Some versions of this set may include optional spray parts. If your set includes these, follow the assembly instructions in the PDF manual for integration. Typically, the spray function requires a small water reservoir and is activated via a specific button or switch on the remote control.
5. Maintenance
5.1. Cleaning
- Building Blocks: Clean blocks with a soft, damp cloth. For stubborn dirt, a mild soap solution can be used, followed by thorough rinsing and drying. Do not use harsh chemicals.
- Electronic Components: Use a dry, soft brush or cloth to gently remove dust from motors, receiver, and battery box. Avoid getting water or liquids on electronic parts.
- Wheels/Tires: Remove any debris (hair, dust, small objects) from the tires and wheel wells.
5.2. Storage
- When not in use, turn off all power switches (Battery Box, Remote Control).
- Remove batteries from the Battery Box and Remote Control if storing for extended periods to prevent leakage.
- Store the RC car and components in a cool, dry place away from direct sunlight and extreme temperatures.
- Keep small parts in a container to prevent loss.
5.3. Battery Care
- Always use the recommended type of batteries.
- Replace all batteries at the same time; do not mix old and new.
- Dispose of used batteries responsibly according to local regulations.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Car does not move | 1. Batteries low or incorrectly installed. 2. Power switches off. 3. Loose wiring connections. 4. Remote not paired. | 1. Replace batteries, check polarity. 2. Turn on Battery Box and Remote Control. 3. Check all motor and battery box connections to receiver. 4. Re-pair remote control (refer to PDF manual). |
| Car moves slowly or inconsistently | 1. Low batteries. 2. Obstruction in drivetrain. 3. Motor issue. | 1. Replace batteries. 2. Check gears and axles for debris or misalignment. 3. Contact seller if motor is faulty. |
| Steering not working | 1. Servo motor not connected or faulty. 2. Steering mechanism obstructed. | 1. Check servo motor connection to receiver. Contact seller if faulty. 2. Ensure steering linkages are free to move. |
| Remote control unresponsive | 1. Low batteries in remote. 2. Remote not paired with receiver. | 1. Replace batteries in remote. 2. Re-pair remote control (refer to PDF manual). |
| Missing or broken parts | Manufacturing defect or shipping damage. | Contact the seller for replacement parts. |
7. Specifications
| Feature | Detail |
|---|---|
| Brand Name | wishiot |
| Model Number | Four-wheel Drive Building Blocks |
| Type | BLOCKS |
| Material | Plastic |
| Block Size | Small building block (Compatible with Lego) |
| Is Electric | Yes (Batteries not included) |
| Remote Control | Yes (Included, requires user-supplied batteries) |
| Certification | CE |
| Recommend Age | 14+y |
| Warning | Not eat |
| Work with | for MOC Power Functions |
| Package Length | 26 cm |
| Package Width | 20 cm |
| Package Height | 8 cm |
| Package Weight | 0.495 kg |

Figure 7.1: Assembled chassis dimensions (approx. 25cm L x 17cm W x 10.5cm H).

Figure 7.2: Tire dimensions (75.1mm x 28mm).
8. User Tips
- Digital Instructions: If the printed instructions are difficult to read, download the PDF manual for a clearer view on a larger screen (tablet, computer).
- Modularity: This set is a great base for custom designs. Feel free to experiment with different block configurations once you understand the core mechanics.
- Gear Reduction: For advanced users, consider experimenting with different gear ratios for more torque, especially if driving on uneven surfaces.
- Compatibility: The building blocks are compatible with other major building block brands, expanding your creative possibilities.
- Assembly Patience: This is a complex build recommended for experienced builders or adults. Take your time and follow each step carefully.
9. Frequently Asked Questions (FAQ)
Q: Where can I find the assembly instructions?
A: A detailed assembly manual is provided in PDF format. You can download it here: Download PDF Manual.
Q: Is the 'Set 2 and Power' package complete with a motor and all necessary components for RC operation?
A: The product is offered in various configurations. Packages like 'Power Group' or 'Full Set' typically include the necessary motors, receiver, battery box, and remote control for RC functionality. If you selected a specific 'Set' option, please refer to the product description at the time of purchase to confirm included components. Generally, any set described as 'Electric Set' or including 'Power' in its name will contain the electronic components.
10. Compliance and Warnings
10.1. California Proposition 65 Warning
⚠️ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
10.2. General Safety
- Not suitable for children under 3 years due to small parts.
- Recommended age: 14+ years.
- Do not ingest any parts.
- Adult supervision is recommended during assembly and operation for younger users.
11. Warranty and Support
For any issues regarding missing parts, defective components, or operational problems not covered in this manual, please contact the seller directly through your purchase platform. Provide your order number and a detailed description of the issue for prompt assistance.