1. Product Introduction
Thank you for choosing the INSE N370 Cordless Stick Vacuum Cleaner. This manual provides important information for the safe and efficient use of your appliance. Please read it thoroughly before first use and keep it for future reference.
Components Overview
Familiarize yourself with the parts of your vacuum cleaner:
Image: The INSE N370 vacuum cleaner in stick and handheld configurations, along with various attachments like a crevice tool, 2-in-1 brush, and washable filters.
| Name | Quantity | Name | Quantity |
|---|---|---|---|
| Main Motor | 1 | Wall Bracket | 1 |
| Metal Tube | 1 | Adaptor | 1 |
| Floor Brush | 1 | Plastic filter screen | 1 |
| 2-in-1 Brush | 1 | Clean Brush | 1 |
| Long Crevice | 1 | Filter | 2 |
2. Setup
Assembly
- Slide the telescopic tube onto the main motor until it clicks securely.
- Push the telescopic tube into the floor brush until it clicks.
- For cleaning high positions, accessories can be connected directly to the tube. You can adjust the length by pressing the button below the metal tube.
Image: Demonstrates the vacuum's versatility, showing it used as a stick vacuum, handheld vacuum, and with various attachments for different cleaning tasks.
Wall Mount Installation
Choose a location close to a power outlet, high enough to allow the telescopic wand and floor nozzle to hang freely.
- Place the wall mount against the wall and mark drill holes with a pencil.
- Drill holes (with a 1/4" bit) and insert drywall anchors.
- Insert screws through the holes on the mount and tighten until firmly attached.
Charging
The battery must be fully charged before first use as the product is delivered uncharged.
Method 1: Wall Mount Charging
- Place the main motor on the wall mount.
- Connect the socket and main motor with the adaptor and cord. The power indicator will flicker during charging.
Method 2: Flat Surface Charging
- Place the main motor on a flat surface.
- Connect the socket and main motor with the adaptor and cord. The power indicator will flicker during charging.
Tip:
- In case of dropping, the appliance should be charged horizontally, without the brush and extension tube.
- General charging time: 4-5 hours.
Image: Diagram illustrating the 2200mAh battery, indicating a runtime of 25-40 minutes and a quick charge time of 5 hours.
Battery Charging Signals:
- Charging time may be longer if room temperature is above 30°C or if recharged immediately after use.
- Always recharge the vacuum cleaner after each usage.
- Unplug when not charging.
- If not in use for more than two months, disconnect from power supply. To ensure longer service life, charge it completely every two months.
- The vacuum cleaner or adapter may become hot during charging; take necessary precautions to avoid contact.
3. Operating Instructions
To prevent obstructions, large debris (e.g., large paper scraps, packaging film) should be removed in advance.
- Click the "Power Switch" to start cleaning.
- Press "MAX" to switch between intense cleaning and energy-saving suction modes (according to your needs).
- Click the "Power Switch" again to stop cleaning.
Image: Diagram illustrating the two suction modes, demonstrating effective cleaning of various debris like coffee beans, cat litter, hair, and general residue.
Image: Shows the vacuum's flexible head, capable of 180° left/right swivel and 90° up/down tilt for easy maneuverability around and under furniture.
4. Maintenance
To ensure maximum performance, regular maintenance of components is strongly recommended.
Cleaning Non-Electrical Parts of the Main Motor
- Turn off the vacuum before cleaning.
- Wipe the surface with a clean cloth.
- Be cautious not to get water into the inner part of the main motor.
Do not place the vacuum cleaner under direct sunlight or in a wet place after cleaning.
Cleaning Detachable Roller Brush
If the roller brush gets tangled or stuck, an alert will appear on the LED Display. Clean it promptly.
- Unlock the side lock on the bottom side of the cleaner head.
- Remove the side cover and take out the roller brush.
- Use the Clean Brush gadget to clean tangled hairs.
Cleaning Plastic Filter Screen & Filter
IMPORTANT
- Check and clean the Plastic filter screen & Filter regularly.
- Clean the filter if suction performance declines.
- Replace the filter if it is broken or cannot maintain suction performance.
- Do not bend or squeeze the filter.
Image: Exploded view of the 5-stage filtration system, showing the air outlet sponge, cyclonic filter, main filter, and dust box. Inset images show washable components.
Image: Two washable filter cottons, indicating they can be cleaned with water for reuse.
- Detach the main motor and dust cup. Take out the filter from the main motor and the filter component from the dust cup. Hold the strainer, rotate the filter holder, then take out the filter.
- If too dirty, wash the strainer and sponge with cool water, and clean the filter with the cleaning brush.
- Ensure the Plastic filter screen & Filter are completely dry before refitting.
- Do not charge if the ambient temperature is lower than 5°C or higher than 40°C.
- Insufficient power indicator for quantity of electricity flickers when you get insufficient power in operation process.
Emptying the Dust Cup
Empty the dust cup regularly to ensure constant suction.
- Hold the cleaner over a waste basket. Press the lever to release the bottom lid of the dust cup to empty it.
- Remove the dust cup by twisting to the 'unlock' position. Empty the contents, then reattach the dust cup and twist to the 'lock' position.
- Twist the dust cup and remove. Twist the filter screen and remove. Lift out the foam filter. Rinse and dry THOROUGHLY. Assemble after each part has dried completely.
Tip: Above steps are suggested after each dust bin empty.
Caution during Maintenance
- Pay attention to sharp objects such as glass to prevent injury.
- Do not wash the mechanical part of the dust box.
- Ensure each part is completely dry before next usage.
- Do not scrub the filter or apply undue force.
- Ensure the filter is correctly secured during assembly.
- Change the filter if damaged or if cleaning does not return it to its pristine state.
5. Troubleshooting
Refer to the table below for common issues and their solutions:
| Problem | Possible Causes | Solution |
|---|---|---|
| Vacuum stops working |
|
|
| Vacuum cleaner works for a few seconds then shuts down (indicator lights flash 5 times) | Blockage of the roller brush activates the Rotation-Clogging Protective System. |
|
| Suction power is getting weaker |
|
|
| Battery cannot be charged |
|
|
6. Specifications
| Parameter | Value | Parameter | Value |
|---|---|---|---|
| Product Category | N300 | Weight (All Accessories Included) | 1.8KG |
| Net weight | 1.1KG | Nominal Voltage | 22.2V |
| Nominal Power | 175W | Current Input | 100V-240V~50/60Hz |
| Battery Capacity | 2200 mAh | Current Output | 26.5V |
| Retractable Tube | 47/77cm | Size | 43.5*28.5*18.0cm |
7. Safety Instructions
- Do not place the vacuum cleaner close to heat sources, radiation, or burning cigarettes.
- Do not use the appliance to remove the following objects:
- All liquids such as water and solvents.
- Lime, cement, ash, and other construction dust and garbage.
- Hot objects, such as cigarette butts.
- Sharp debris, such as glass shards, etc.
- Inflammable and explosive articles, such as gasoline or alcohol products.
- Do not let children play with and operate the vacuum cleaner to prevent accidents.
- Your vacuum cleaner is an electric appliance: it must be used appropriately. Do not leave the operating vacuum cleaner unattended.
- The power must be turned off during cleaning, maintenance, or when in storage.
- Do not pull the power plug to turn off the vacuum cleaner. Hold the plastic part of the plug to remove it from the power socket.
- The power supply voltage must correspond to that of the vacuum cleaner charging voltage.
- Keep the power cord away from sharp objects to prevent it from being damaged.
- To prevent fires, do not immerse the vacuum cleaners in water, do not expose them to any heating appliances.
- Do not drag the power cord when moving the charging station.
- In the case of the following situations, do not use the vacuum cleaner and send it immediately to the nearest approved maintenance facility if:
- The vacuum cleaner fell and consequently damaged.
- The power cord is damaged.
- Stop operating the vacuum cleaner if the suction inlet is blocked to prevent damages (such as overheating) to the motor or deformations to the vacuum plastic part occasioned by an overheating motor.
8. User Tips
- For optimal performance, ensure the dust cup is emptied regularly and filters are cleaned as recommended.
- Always check for tangled hair on the roller brush, especially if you notice a decrease in suction or an LED alert.
- When charging, ensure the adapter is the original one and securely plugged in to prevent issues.
- The 6-in-1 design allows for versatile cleaning; utilize the different attachments for specific tasks like crevices, upholstery, or high areas.
9. Warranty & Support
NOTE: This warranty term gives you specific legal rights, and you may also have other rights which vary from state to state.
24-month Warranty & Lifetime Customer Support
This warranty applies only to eligible purchases made directly from authorized distributors. Coverage applies to the original owner and to the original product only and is not transferable.
How to Initiate a Warranty Claim
If your appliance operates improperly while in use under normal household conditions within the warranty period, please contact our customer support at vacuumhelpdesk@gmail.com to fill out the warranty form and initiate a claim.