GTMEDIA GTmedia V8 Finder PRO2

Contents

GTMEDIA V8 Finder Pro2 Digital Satellite Signal Finder Meter

User Instruction Manual

1. Introduction

This manual provides detailed instructions for the safe and efficient operation of your GTMEDIA V8 Finder Pro2. This device is a versatile digital satellite signal finder meter designed to assist in the installation and alignment of satellite dishes, terrestrial antennas, and cable systems. It supports DVB-S2/S2X, DVB-T/T2, and DVB-C standards, featuring a 4.3-inch HD LCD screen and HEVC MPEG-4 decoding.

2. Important Safety Instructions

Please read and follow these safety guidelines carefully to ensure safe and proper operation of your device:

  • Be sure to read this user manual before starting your operation.
  • You must install the dish with correct direction and angle. If the dish is not working properly, contact your local dealer.
  • When the unit is suddenly moved to a hot area from a cold area, it may cause some problems. In that case, turn off the power, and turn on again after 1-2 hours.
  • Keep meter placed in clean space with sufficient ventilation.
  • Do not cover the meter with or place it on a unit that emits heat.
  • Clean the case by a soft cloth with a little washing liquid.
  • Do not remove the cover.
  • Do not let the unit exposed to extreme heat, cold or humid conditions.
  • No liquids or any other materials to come inside of the unit.
GTMEDIA V8 Finder Pro2 connected to a satellite dish and TV

Figure 1: GTMEDIA V8 Finder Pro2 in use with a satellite dish and TV setup.

3. Product Overview & Illustration

Familiarize yourself with the components and interfaces of your V8 Finder Pro2.

Front and back view of GTMEDIA V8 Finder Pro2

Figure 2: Front and Rear View of the V8 Finder Pro2.

3.1. Front Panel and Side Interfaces

No.DescriptionFunction
1LCD ScreenVideo display
2Battery Level IndicatorBattery level display (5 levels)
3PowerPower indicator light
422KHz22kHz indicator light
513V/18VVertical/Horizontal polarization voltage output light
6LockSignal Lock indicator light
7Charger (Note1)Charger indicator light (Red: Charging, Blue: Full)
8DVBDVB mode switch for LCD
9AHDAHD IN mode switch for LCD
10AV INAV IN mode switch for LCD
11LCDTurn on and off the screen backlight
12Red & RECRed Key & Enter record function
13Green & SUBTGreen key & subtitle interface
14Yellow & TEXTYellow key & Teletext interface
15Blue & EPGBlue key & EPG interface
16MENUShow the main menu on the screen or jump back to previous menu in sub-menu setting conditions
17EXITEscape from present menu and save the settings
18LOOPLOOP Search interface
19SPECSpectrum interface
20Navigation KeyVolume Control or move cursor, channel or change, confirm etc.
210-9Number key to select channels or enter programming
22TV/RTV and radio switch
23AUDIOAudio interface
24SATDisplay the satellite list
25INFOInfo interface
26MUTEEnable or disable the audio output
27LNB INConnect to satellite antenna cable
28ANT INConnect to antenna of DVB-T/T2/C signal
29AHDConnect the analog AHD cable to the LCD screen
30USBConnect to USB memory or USB WIFI
31Power InputConnect to adaptor input (9V/2A)
32Power SwitchTurn on/off meter
33HDMIUse HDMI cable to connect for TV
34DC12V OUTConnect to AHD power supply (1Ah MAX)
35AV INConnect to AV port for meter
36SpeakerSpeaker integrated

4. Setup Instructions

Before using your V8 Finder Pro2, ensure all necessary connections are made and basic settings are configured.

4.1. Initial Setup and Main Menu Navigation

After powering on the device, press the MENU button to display the Main Menu. The main menu provides access to various functions:

  • Satellite
  • Terrestrial
  • Cable
  • Spectrum
  • Loop Search
  • Calculate
  • Other
  • System Setting
Main menu icons for GTMEDIA V8 Finder Pro2

Figure 3: Main Menu Interface.

4.2. System Settings

Navigate to System Setting from the Main Menu and press OK to configure basic device parameters.

  • Language: Change the system default language.
  • Local Longitude/Latitude: Set your geographical coordinates for accurate calculations.
  • TV System: Switch TV system (Auto/PAL/NTSC).
  • Video Resolution: Adjust video output resolution (e.g., 1080i, 720p).
  • LNB POWER: Enable or disable LNB power.
  • Beeper: Turn on/off the beep tone for lock alarms.
  • Local Time Setting: Configure local time.
  • WiFi Manager: Set WiFi connection settings.

4.3. Terrestrial (DVB-T/T2) Setup

Select Terrestrial from the Main Menu and press OK to enter the DVB-T2 scan setup.

  • Country: Change the default country.
  • Frequency Channel: Change the channel number.
  • Frequency (KHz): Input the frequency value using the number keys.
  • Bandwidth: Change the bandwidth (6, 7, or 8M).
  • Antenna Power: Turn the antenna power on and off.
  • LCN: Turn the LCN on and off.
  • Scan: Press the Blue key to search the current channel.
  • Auto Search: Press the Yellow key to auto search channels.

4.4. Satellite (DVB-S2/S2X) Setup

Select Satellite from the Main Menu and press OK to enter the Satellite Find menu.

  • Satellite: Select the desired satellite.
  • LNB Freq: Select the LNB frequency.
  • Frequency Channel: Select the Transponder (TP) you want.
  • Frequency / Symbol Rate: Input the current transponder's frequency and symbol rate using number keys.
  • Polarity: Change vertical or horizontal polarization.
  • DiSEqC1.0 / DiSEqC1.1: Set the port number for DiSEqC switches.
  • 22K: Turn on or off the 22 kHz switch.
  • Motor Setup: If DiSEqC1.2 or USALS is selected, input the Center Frequency.
  • TP Search: Press the Yellow key to search the current TP.
  • Blind Scan: Press the Blue key to perform a blind scan for the current satellite.

4.5. Cable (DVB-C) Setup

Select Cable from the Main Menu and press OK to enter the DVB-C scan setup.

  • Frequency: Input the cable frequency.
  • Symbol Rate: Input the symbol rate.
  • Modulation: Select the modulation type (e.g., QAM64).
  • Scan: Press the Blue key to search the current channel.
  • Range Search: Press the Yellow key to enter the range search setting interface.

5. Operating Instructions

This section details how to use the GTMEDIA V8 Finder Pro2 for various signal finding and analysis tasks.

5.1. Signal Finding and Alignment

After configuring the appropriate DVB mode (Satellite, Terrestrial, or Cable) as described in the Setup section, connect your antenna or LNB cable to the respective input port (LNB IN for satellite, ANT IN for terrestrial/cable).

  • Strength and Quality Bars: Observe the signal strength and quality bars on the LCD screen. Adjust your antenna/dish direction and elevation until these values are maximized.
  • Audio Tone: The device may emit an audio tone that changes in pitch or frequency as signal quality improves, aiding in fine-tuning.
  • Lock Indicator: The "Lock" LED will illuminate when a stable signal is acquired.

5.2. Spectrum View

Select Spectrum from the Main Menu to view the signal spectrum. This graphical representation helps in identifying interference and optimizing signal reception.

  • Sat-Spectrum: For satellite signals.
  • Terr-Spectrum: For terrestrial signals.
  • Cable-Spectrum: For cable signals.

Select Loop Search from the Main Menu to perform a loop search for available channels. This function scans a range of frequencies to find all active transponders or channels.

5.4. Calculate (Satellite Pot Angle)

Select Calculate from the Main Menu. If your local longitude and latitude are set in System Settings, this function will display the LNB angle, orientation, and elevation required for your chosen satellite, assisting in precise dish alignment.

5.5. Other Functions

From the Main Menu, select Other to access additional features:

  • TV Channel List / Radio Channel List: View scanned channels.
  • Media Player: Play media files from a USB drive.
  • EPG: Electronic Program Guide.
  • USB Upgrade: For firmware updates.
  • Factory Setting: Reset the device to factory defaults.
  • Information: View device information.

Video 1: Demonstration of GTMEDIA V8 Finder Pro2 features and interface navigation.

6. Maintenance

To ensure the longevity and optimal performance of your GTMEDIA V8 Finder Pro2, follow these maintenance guidelines:

  • Cleaning: Use a soft, dry cloth to clean the exterior of the device. For stubborn dirt, slightly dampen the cloth with water or a mild, non-abrasive cleaning solution. Do not use strong chemicals or solvents.
  • Storage: When not in use, store the device in a cool, dry place away from direct sunlight, extreme temperatures, and high humidity.
  • Battery Care: For long-term storage, ensure the battery is partially charged (around 50%). Avoid fully discharging the battery for extended periods.
  • Avoid Impact: Protect the device from drops and impacts, especially the LCD screen.
  • Ventilation: Ensure the ventilation slots are not blocked during operation to prevent overheating.

7. Troubleshooting

If you encounter issues with your GTMEDIA V8 Finder Pro2, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Device does not power on.Low battery; Power adapter not connected or faulty; Power switch off.Charge the device; Check power adapter and connection; Ensure power switch is ON.
No signal detected.Incorrect antenna/LNB connection; Wrong satellite/transponder settings; Antenna/dish misalignment; LNB faulty.Check cable connections; Verify satellite/transponder settings; Adjust antenna/dish; Test with another LNB if possible.
Poor signal quality.Fine-tuning needed; Obstruction in signal path; Cable quality issue.Adjust antenna/dish for maximum quality; Remove obstructions; Check/replace cables.
Screen frozen or unresponsive.Software glitch.Restart the device. If issue persists, perform a factory reset (data will be lost).
USB upgrade fails.Incorrect firmware file; USB drive issue; Power interruption during upgrade.Ensure correct firmware for V8 Finder Pro2; Use a formatted USB drive; Do not power off during upgrade.

8. Specifications

Key technical specifications for the GTMEDIA V8 Finder Pro2:

FeatureDetail
TypeDIGITAL
High DefinitionYes
FTA (Free To Air)Yes
Model NumberGTmedia V8 Finder PRO2
Brand NameGTMEDIA
CertificationCE
Display4.3-inch HD LCD Screen
DecodingHEVC MPEG-4 (H.264/H.265 10-bit)
Battery Capacity4000mAh
Charging9V Fast Charging
ConnectivityUSB 2.0, 2.4G WiFi
Signal InputDVB-S/S2/S2X, DVB-T/T2, DVB-C
Output PortsHDMI, AV Out, DC 12V Out
Input PortsAV In, AHD In

9. User Tips

Based on common user inquiries and feedback, here are some tips for optimizing your experience with the GTMEDIA V8 Finder Pro2:

  • Firmware Updates: Regularly check the official support channels for firmware updates. Updates can improve performance, add features, and fix bugs. Use the "USB Upgrade" function carefully, ensuring the correct file and stable power.
  • Battery Life: To maximize battery life during extended use, consider reducing screen brightness when possible.
  • Signal Accuracy: For the most accurate signal readings, ensure all cable connections are tight and free from damage.

10. Warranty and Support

For product feature introduction, user guides, software updates, and technical support, please visit the official resources:

Please refer to the original packaging or purchase documentation for specific warranty terms and conditions.

Contents of the GTMEDIA V8 Finder Pro2 package including device, cables, adapter, and manual

Figure 4: Package Contents of GTMEDIA V8 Finder Pro2.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.