1. Introduction
Thank you for choosing the GTMEDIA V8 Finder 2. This portable digital satellite finder is designed to assist you in quickly and accurately aligning your satellite dish. Featuring a 3.5-inch HD LCD screen, it supports DVB-S/S2/S2X signals and offers a range of functions including spectrum analysis, loop search, and pan angle calculation. This manual provides essential information for safe operation, setup, and maintenance of your device.
2. Important Safety Instructions
To ensure safe and proper operation, please observe the following guidelines:
- Always read this user manual thoroughly before operating the device.
- Ensure your satellite dish is installed with the correct direction and angle. If issues arise, consult your local dealer.
- If moving the unit from a cold to a hot environment, allow 1-2 hours for it to acclimatize before powering on to prevent potential problems.
- Operate the meter in a clean area with adequate ventilation.
- Do not cover the meter or place it near heat-emitting devices.
- Clean the device casing with a soft cloth lightly dampened with cleaning liquid.
- Never attempt to remove the device cover.
- Avoid exposing the unit to extreme temperatures (heat or cold) or high humidity.
- Prevent any liquids or foreign materials from entering the unit.
Connection Diagram
The following diagram illustrates typical connections for your GTMEDIA V8 Finder 2:

Description: This diagram shows the various input and output ports of the V8 Finder 2 and how they connect to other devices. The LNB IN port connects to the satellite antenna. The HDMI OUT and AV OUT ports connect to a television. The AV IN port can receive signals from an external source like a TV box. The USB port is for data transfer and upgrades, and the DC IN port is for power.
3. Package Contents
Upon opening your GTMEDIA V8 Finder 2 package, you should find the following items:
- GTMEDIA V8 Finder 2 Digital Satellite Finder Unit
- User Manual
- USB Cable
- Power Adapter (not explicitly shown but implied by charging features)
- F-type Connector (adapter)

Description: This image displays the contents of the GTMEDIA V8 Finder 2 package, including the main unit, user manual, USB cable, and an F-type connector.
4. Product Overview and Controls
Familiarize yourself with the device's layout and controls:
Front Panel

Description: This image shows the front view of the GTMEDIA V8 Finder 2, highlighting its 3.5-inch HD LCD screen and the numeric keypad with navigation buttons. The screen displays the main menu icons for Installation, Spectrum, Loop Search, Calculate, Channel, Media, Tools, and System.
Side and Rear Panels

Description: This image provides the dimensions of the V8 Finder 2 (155mm height, 95mm width) and shows the various ports on its sides, including HDMI, AV OUT, AV IN, USB 2.0, and the LNB IN connector on the top.
Controls and Ports Description
| No. | Description | Function |
|---|---|---|
| 1 | LCD Screen | Video display |
| 2 | Battery Indicator | Battery level display (charge when red warning appears) |
| 3 | Power | Power indicator light |
| 4 | 22KHz | 22kHz indicator light |
| 5 | 13V/18V | Vertical/Horizontal polarization voltage output light |
| 6 | Lock | Signal Lock indicator light |
| 7 | Charger | Charging: Flashing red; Fully charged: Red and blue |
| 8 | Red & REC | Red Key & Enter record function |
| 9 | Green & SUBT | Green key & subtitle interface |
| 10 | Yellow & TEXT | Yellow key & Teletext interface |
| 11 | Blue & AUDIO | Blue key & Audio interface |
| 12 | MENU | Show main menu or jump back to previous menu |
| 13 | EXIT | Escape from current menu and save settings |
| 14 | Navigation key | Volume Control, move cursor, channel change, confirm |
| 15 | 0-9 | Number key to select channels or enter programming |
| 16 | SPEC | Spectrum interface |
| 17 | LOOP | LOOP Search interface |
| 18 | B.LIGHT | Display of LCD on/off |
| 19 | TV/R | TV and radio switch |
| 20 | INFO | Info interface |
| 21 | SAT | Display the satellite list |
| 22 | MUTE | Enable or disable the audio output |
| 23 | LNB IN | Connect to satellite antenna cable |
| 24 | USB | Connect to USB memory |
| 25 | DC IN | Connect to adaptor input (5V/9V/12V) |
| 26 | Power Switch | Turn on/off meter |
| 27 | HDMI | Use HD cable to connect for TV |
| 28 | AV OUT | Connect to AV port for TV |
| 29 | AV IN | Connect to AV port for meter |
| 30 | Speaker | Speaker integrated |
5. Initial Setup
Charging the Device
Before first use, ensure your V8 Finder 2 is fully charged. Connect the provided power adapter to the DC IN port (25) and plug it into a power outlet. The Charger indicator (7) will flash red during charging and turn red and blue when fully charged. The device supports 5V/9V/12V input and 18W fast charging.
Note: The device may restart once when the adapter is plugged in during charging; this is normal operation and not a product fault.
Connecting to Satellite Antenna
Connect your satellite antenna cable to the LNB IN port (23) on the V8 Finder 2.
Powering On/Off
Use the Power Switch (26) to turn the device on or off.
6. Operating Instructions
After connecting the cables and powering on, press the MENU button (12) to access the Main Menu. Use the Navigation keys (14) to select options and the OK button to confirm.
Main Menu Overview
- Installation: For setting up satellites and transponders.
- Spectrum: Displays real-time signal spectrum.
- Loop Search: Performs a loop search for signals.
- Calculate: Helps calculate dish pan angle based on location.
- Channel: Manages TV and Radio channels.
- Media: Accesses multimedia playback and recording functions.
- Tools: Provides system information, factory reset, and USB functions.
- System: Configures device settings like language, AV output, and time.
6.1. Installation
Select 'Installation' from the Main Menu to configure satellite settings:
- Satellite Selection: Use the Navigation keys to highlight and select the desired satellite from the list. A tick icon indicates selection.
- LNB Freq: Set the correct Local Oscillator (LO) frequency for your LNB (e.g., Universal, C-Band, Ku-Band).
- DiSEqC1.0 / DiSEqC1.1: Configure the DiSEqC port number if you are using a DiSEqC switch.
- 22K: Toggle the 22kHz tone on or off, typically used for switching between high/low bands on some LNBs.
- LNB Power: Set the LNB power output to Horizontal (H), Vertical (V), Auto, or Off. Auto is the default.
- Motor Setup: If using a motorized dish, configure DiSEqC1.2 or USALS settings here.
- Add/Edit/Delete Satellite: Use the Red, Green, and Delete keys respectively to manage satellite entries.
- Satellite Search: After selecting a satellite, press the Blue key to enter the search menu. Configure scan type (Single Satellite, Blind Scan), FTA Only, Scan Channel (TV+Radio, TV, Radio), Network Search, and Scan Mode, then initiate the search.
6.2. Spectrum
Select 'Spectrum' from the Main Menu to view the real-time signal spectrum. This graphical representation helps in fine-tuning dish alignment by showing signal strength and quality across frequencies.
6.3. Loop Search
Select 'Loop Search' to perform a signal loop search. This function can help identify active transponders and signal presence.
6.4. Calculate
The 'Calculate' function assists in determining the optimal dish alignment angles:
- Enter the Longitude of your target satellite.
- Enter your Local Longitude and Local Latitude using the numeric keypad.
- The device will calculate the necessary pan and tilt angles for your dish.
6.5. Channel
Select 'Channel' to manage your TV and Radio channels:
- TV Channel List / Radio Channel List: View and manage scanned channels.
- EPG: Access the Electronic Program Guide (if available).
- Timer Setting: Set timers for recording or viewing.
- Favorite: Create and manage favorite channel lists.
- Delete All: Delete all scanned channels.
6.6. Media
The 'Media' menu allows you to access multimedia functions:
- Music: Play audio files.
- Picture: View image files.
- Movie: Play video files.
- Record Manager: Manage recorded programs.
- HDD Information: View information about connected storage.
- DVR Configuration: Configure Digital Video Recorder settings.
6.7. Tools
The 'Tools' menu provides utility functions:
- Information: View product details and software version.
- Factory Setting: Reset the device to factory defaults. Warning: This will erase all user settings and scanned data.
- USB Upgrade: Update the device firmware via USB. Ensure the correct firmware file is on a USB drive. Important: Do not power off or remove the USB drive during an upgrade to avoid damaging the device.
- USB Backup: Backup device software or database to a USB drive.
- Record: Record the current TS stream to a connected USB drive.
6.8. System
Configure general device settings in the 'System' menu:
- Language: Change the display language.
- AV Setting: Configure TV System (PAL/NTSC), Video Resolution (e.g., 1080p), Aspect Mode, and Audio settings.
- Local Time Setting: Set the time zone and current time.
- OSD Setting: Adjust On-Screen Display settings, including beeper sound.
- WiFi Manager: Configure Wi-Fi network connections (if applicable).
Product Demonstration Video
Description: This video provides a visual overview and demonstration of the GTMEDIA V8 Finder 2, showcasing its features, interface, and basic operation.
7. Maintenance
- Cleaning: Use a soft, dry cloth to clean the exterior of the device. For stubborn dirt, slightly dampen the cloth with water or a mild, non-abrasive cleaner. Do not use strong chemicals or solvents.
- Storage: When not in use for extended periods, store the device in a cool, dry place away from direct sunlight and extreme temperatures.
- Battery Care: To prolong battery life, avoid fully discharging the battery frequently. If storing for a long time, charge the battery to about 50% every few months.
8. Troubleshooting
- Device does not power on: Ensure the battery is charged. Connect the power adapter and try again. Check the power switch.
- No signal detected: Verify the antenna cable is securely connected to the LNB IN port. Check LNB power settings (13V/18V). Ensure the correct satellite and transponder frequencies are selected in the 'Installation' menu.
- Screen is blank or frozen: Try restarting the device by turning it off and on. If the issue persists, perform a 'Factory Setting' reset (note: this will erase all data).
- Poor signal quality: Adjust the satellite dish alignment slowly and incrementally while observing the signal strength and quality indicators on the V8 Finder 2. Check for any obstructions between the dish and the satellite.
- Device restarts unexpectedly: If this happens when plugging in the charger, it is normal behavior. If it occurs randomly, ensure the device is not overheating and that the battery is adequately charged.
9. Specifications
| Feature | Specification |
|---|---|
| Model | GTMEDIA V8 Finder 2 |
| Display | 3.5-inch High Definition TFT LCD Screen |
| Satellite Standard | DVB-S/S2/S2X |
| Decoding Support | BISS/PowerVu, VCM/ACM/Multi-stream/T2MI, PLP, MPEG2, MPEG4, H.264 (8 Bit) |
| Input Frequency | 950-2150MHz |
| Input Impedance | 75Ω |
| LNB Power | 13V/18V/OFF, Max 400mA |
| DiSEqC | DiSEqC 1.0/1.1/1.2/USALS Support |
| Battery | 7.4V / 4000mAh Li-Ion Battery |
| Charging | DC 5V/9V/12V, 18W Fast Charge Support |
| USB Port | USB 2.0 (for software upgrade and media playback) |
| Dimensions (Unit) | 155mm (H) x 95mm (W) |
| Certification | CE |
10. User Tips
- For optimal signal acquisition, make small, slow adjustments to your dish while monitoring the signal quality on the V8 Finder 2.
- Always ensure your LNB frequency settings match your actual LNB for accurate readings.
- Keep the firmware updated via the USB upgrade function to ensure compatibility and access to the latest features.
11. Warranty and Support
For product feature introductions, user guides, software updates, or technical support, please visit the official forum at www.freesat.cn or the official YouTube channel at www.youtube.com/c/gtmediapub.
Please refer to your product's warranty card for specific warranty terms and conditions.
This manual is subject to change without prior notice.