BEISHI Universal Fixed TV Wall Mount Bracket

1. Introduction

Thank you for choosing the BEISHI Universal Fixed TV Wall Mount Bracket. This manual provides detailed instructions for safe installation, operation, and maintenance of your TV wall mount. Please read this manual thoroughly before installation and keep it for future reference.

This wall mount is designed to securely hold flat panel TVs ranging from 26 to 65 inches, with a maximum load capacity of 50kg (110lb).

2. Safety Information

WARNING: Failure to read and follow these instructions may result in serious personal injury, property damage, or voiding your warranty.

• This product is intended for indoor use only.
• Ensure the mounting surface can safely support the combined weight of the mount and your TV. If unsure, consult a qualified professional.
• Do not install into hollow walls, foam walls, or other non-load-bearing walls unless specifically reinforced.
• Always use an assistant for lifting and positioning the TV.
• Ensure no electrical wires, water pipes, or gas lines are present in the drilling area.
• Do not exceed the maximum load capacity of 50kg (110lb).
• Keep children away from the installation area.
• Check all connections regularly to ensure they remain secure.

3. Package Contents

Please check that all components are present and undamaged before installation. If any parts are missing or defective, contact your retailer.

Included Hardware:

• (A) Expansion bolts: X4
• (B) Expansion tube: X4
• (C) Heightening pad: X4
• (D) M4x20 screws: X4
• (E) M6x20 screws: X4
• (F) M5x45 screws: X2
• (G) D6 gasket: X8
• (H) Level: X1
• (I) Hook: X2
• (J) Panel: X1

Note: Due to variations in TV models and hole distances, the included screws may not be universally compatible. If the provided screws are unsuitable, please obtain appropriate screws from a hardware store.

4. Setup and Installation

Follow these steps carefully for a secure installation. It is recommended that professional installers perform the installation.

4.1. Installation Video Guide

4.2. Step-by-Step Installation Instructions

The level gauge (H) is inside the packaging and needs to be installed on the bracket for use.

Step 1: Fixing the Wall Plate (J)

For Solid Concrete Walls:

1. Position the wall plate (J) on the desired location on the wall.
2. Use the level (H) to ensure the plate is perfectly horizontal.
3. Mark the drilling points through the holes on the wall plate using a pencil.
4. Use an impact drill to drill holes at the marked points.
5. Insert expansion tubes (B) into the drilled holes.
6. Align the wall plate (J) with the holes and secure it using expansion bolts (A) and D6 gaskets (G).

For Wooden Walls:

1. Position the wall plate (J) on the desired location on the wall.
2. Use the level (H) to ensure the plate is perfectly horizontal.
3. Mark the drilling points through the holes on the wall plate using a pencil.
4. No expansion tubes (B) are required for wooden walls.
5. Align the wall plate (J) with the holes and secure it directly to the wall using M5x45 screws (F) and D6 gaskets (G) with a screwdriver.

Step 2: Attaching Hooks (I) to the TV

1. Lay your TV face down on a soft, clean surface to prevent scratches.
2. Identify the VESA mounting holes on the back of your TV.
3. Attach the hooks (I) to the back of your TV using the appropriate M4x20 screws (D) or M6x20 screws (E) and D6 gaskets (G).
4. If needed, install heightening pads (C) between the hook and the TV for proper fit or ventilation. These can be installed either between the hook and the TV, or above the hook.

Step 3: Hanging the TV on the Wall

1. With assistance, carefully lift the TV.
2. Align the hooks (I) on the TV with the top edge of the wall plate (J).
3. Gently lower the TV until the hooks engage securely with the wall plate.
4. Once the TV is hanging, ensure it is centered and level.
5. Locate the safety screws (usually at the bottom of the hooks) and tighten them to prevent the TV from accidentally lifting off the wall plate.

5. Operating Instructions

This is a fixed TV wall mount. Once installed, the TV position is set. There are no adjustable features for tilt, swivel, or extension.

6. Maintenance

• Periodically check all screws and connections to ensure they are tight and secure.
• Clean the mount with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Inspect the mount for any signs of wear or damage. If any damage is found, do not use the mount and contact customer support.

7. Troubleshooting

If you encounter any issues during or after installation, please review the following:

• TV is not level: Ensure the wall plate was installed horizontally using the level. If not, remove and re-install.
• TV feels unstable: Double-check that all screws are tightened securely, especially the safety screws. Ensure the wall type is appropriate and can bear the weight.
• Screws don't fit TV: Refer to your TV's manual for correct VESA screw sizes. The included screws are common sizes, but some TVs may require different lengths or diameters.

8. Specifications

9. Warranty and Support

This product comes with a standard manufacturer's warranty. For warranty claims, technical support, or any questions regarding your BEISHI TV Wall Mount, please contact your original point of purchase or the manufacturer's customer service department.