Introduction
This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your Shimano Deore BL-M4100 Hydraulic Disc Brake Levers. Please read this manual thoroughly before use to ensure correct and safe operation.
This dealer's manual is intended primarily for use by professional bicycle mechanics. Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using the dealer's manuals. If any part of the information on the manual is unclear to you, do not proceed with the installation. Instead, contact your place of purchase or a distributor for assistance.
All manuals and technical documents are accessible online at https://si.shimano.com.
Product Overview
The Shimano Deore BL-M4100 is a hydraulic disc brake lever designed for mountain bikes, offering intuitive and powerful braking performance. It features quicker brake engagement with a shorter free stroke and a rider-tunable, action-optimized cockpit. The lever has a 10-degree rotation angle setting range for I-SPEC EV shifters.
Key Features:
- Intuitive and powerful braking
- Quicker brake engagement with shorter free stroke
- Rider tunable and action-optimized cockpit
- 10 deg. rotation angle setting range for I-SPEC EV shifter
- Lever size (finger): 2
- Hose joint: Straight
- Clamp band: Open clamp
- Weight: 113g/pc
- Origin: Malaysia
Important Safety Information
The following instructions must be observed at all times in order to prevent personal injury and physical damage to equipment and surroundings. Instructions are classified according to the degree of danger or damage which may occur if the product is used incorrectly.
DANGER
Failure to follow these instructions will result in death or serious injury.
WARNING
Failure to follow these instructions could result in death or serious injury.
- Always wear approved eye protection while performing maintenance tasks.
- Learn proper braking technique and bicycle control characteristics. Improper use may lead to loss of control or a fall.
- Become accustomed to the higher performance of this brake. Larger disc brake rotors (203mm, 180mm) provide higher braking force than 160mm rotors.
- Keep fingers away from the rotating disc brake rotor, as it is sharp and can cause severe injury.
- Do not touch calipers or disc brake rotors while riding or immediately after dismounting, as they become hot and can cause burns.
- Prevent oil or grease from contacting the disc brake rotor and brake pads, as this can impair braking and lead to serious injury.
- Do not use brake pads with a thickness of 0.5 mm or less.
- Replace cracked or deformed disc brake rotors immediately. Do not use if thickness is 1.5 mm or less or if the aluminum surface is visible.
- Avoid continuous brake application, which can increase lever stroke and prevent braking.
- Do not use brakes with fluid leaking.
- Do not apply the front brake too strongly to avoid locking the front wheel and falling.
- Reduce speed and apply brakes early and gently in wet weather or on wet road surfaces to prevent loss of traction and falls.
- Ensure the quick release lever does not interfere with the disc brake rotor.
- Do not use oil other than SHIMANO genuine mineral oil.
- Use only oil from a freshly-opened container.
- Prevent water or air bubbles from entering the brake system.
- Do not use with a tandem bicycle.
- Do not reuse the olive piece or connector insert when reinstalling.
- Cut the brake hose perpendicularly to avoid fluid leaks.
- When handling SHIMANO genuine mineral oil: use appropriate eye protection, avoid contact with eyes (flush with fresh water and seek medical assistance if contact occurs), use gloves, wash skin with soap and water if contact occurs.
- Cover nose and mouth with a respirator in a well-ventilated area when handling mineral oil to avoid nausea from mist or vapors. Seek medical advice if inhaled.
- Do not drink mineral oil. Keep out of reach of children.
- Do not cut, heat, weld, or pressurize the mineral oil container to prevent explosion or fire.
- Dispose of used oil according to local codes.
- Store mineral oil in a cool, dark, sealed container away from heat, flame, and direct sunlight.
- Handle knives carefully when cutting brake hoses or replacing blades.
- Avoid pinching fingers between the lever and tool during operations.
- Clean brake hoses with isopropyl alcohol if mineral oil adheres.
- Do not reuse a split pin that has been removed. If a split pin is reused, there is a risk that it will fail, causing the brake pads to fall out of the caliper, which may result in serious injury.
CAUTION
Failure to follow these instructions could cause personal injury or physical damage to equipment and surroundings.
NOTICE
- Keep tools and blades out of reach of children.
- Use isopropyl alcohol or a dry cloth for cleaning brake hoses and tools. Avoid commercial brake cleaners on plastic parts.
- When the bicycle wheel is removed, install pad spacers. Do not depress the brake lever without pad spacers to prevent pistons from protruding excessively.
- Avoid commercial brake cleaners or silencing agents on seals during maintenance.
- Clean carbon levers with a soft cloth and neutral detergent to prevent material damage.
- Avoid high temperatures and fire for carbon levers.
- Products are not guaranteed against natural wear and deterioration.
- SHIMANO lubricants and maintenance products are highly recommended for maximum performance.
- The 203mm and 180mm disc brake rotors have greater warping potential than 160mm rotors, which may affect brake pad performance.
- Ensure brake caliper mounting boss and dropout are parallel to prevent disc brake rotor and caliper contact.
- The actual product may differ from illustrations in this manual, which are for procedural explanation.
Setup (Installation)
Tools Required
The following tools are needed for installation, removal, adjustment, and maintenance:
| Tool | Description |
|---|---|
| 2 mm hexagon wrench | For various fasteners |
| 2.5 mm hexagon wrench | For various fasteners |
| 3 mm hexagon wrench | For various fasteners |
| 4 mm hexagon wrench | For various fasteners |
| 5 mm hexagon wrench | For various fasteners |
| 8 mm spanner | For various fasteners |
| 7 mm box wrench | For various fasteners |
| Adjustable wrench | For general adjustments |
| SM-DISC | Oil funnel and oil stopper for bleeding |
| TL-BH62 | Hose cutting tool |
| TL-FC36 | Disc brake rotor lock ring tool |
| TL-LR15 | Disc brake rotor lock ring tool |
| Micrometer | For precise measurements |
Installing the Brake Lever
For installation with an I-SPEC EV type shifting lever, refer to the shifting lever's dealer manual. When installing parts onto a carbon frame/handlebar, confirm the recommended tightening torque with the manufacturer to prevent damage.
- Open the clamp band of the brake lever.
- Loosen the mounting screw.
- Press the recessed area of the clamp band with a 2 mm hexagon wrench to disengage the safety latch.
(Diagram: Brake lever clamp band with mounting screw and safety latch indicated.)
- Pull a snap spring to the clamp band side.
(Diagram: Illustrates pulling the snap spring to open the clamp band.)
- Attach the brake lever to the handlebar.
Secure the lever using the mounting screw. Tighten to 4-6 N·m.
(Diagram: Brake lever mounted on handlebar with mounting screw and torque specification.)
When installing the brake lever in combination with a standard type shifting lever, install the brake lever so that the position of the shifting lever band is within the range shown in the figure. After the shifting lever is installed, install the brake lever while checking its position.
(Diagram: Brake lever and shifting lever band positioning on handlebar.)
Installing the Disc Brake Rotor
- Check that the spokes are laced as shown in the figure. Radial lacing cannot be used.
(Diagram: Examples of correct spoke lacing for front left, rear left, rear right, and front right wheels.)
- Set the disc brake rotor on the hub, then secure it with the disc brake rotor lock ring.
Secure with TL-LR15 and an adjustable wrench or TL-FC36. Tighten to 40 N·m.
(Diagram: Disc brake rotor installation with lock ring and tightening tool.)
Disc brake rotor lock ring type Lock ring tightening tool Internal spline type TL-LR15 and adjustable wrench External spline type TL-FC36
Installing the Brake Caliper
Post Mount Type
- Install the wheel with an attached disc brake rotor onto the frame.
- Remove the bleed spacer (yellow).
- Close the tip of the split pin.
- Remove the split pin.
- Remove the bleed spacer (yellow).
(Diagram: Brake caliper with split pin and yellow bleed spacer.)
- Set the brake pad presser spring in the brake pads.
Since there are fins on the front and rear of the finned pads, set the pads as shown in the figure. When a brake pad has markings, take note of the left (L) and right (R) markings to set it.
(Diagram: Brake pad presser spring and finned pad orientation.)
- Install the brake pads.
- Set the brake pads in the caliper.
- Insert a new split pin.
- Open the tip of the split pin.
(Diagram: Steps for installing brake pads and split pin into the caliper.)
- Temporarily install the caliper on the frame without fully tightening the fixing screws so that the caliper can still move horizontally.
If a mount adapter is needed, temporarily install it after setting it on the caliper, with the mark facing up.
(Diagram: Caliper installation without mount adapter, showing temporary fixing screw.)
(Diagram: Caliper installation with mount adapter, showing temporary fixing screws for front and rear.)
- Depress the brake lever so that the disc brake rotor is held between the pads, then tighten the caliper fixing screws.
If the brake hose is not yet installed, install it first. Tighten caliper fixing screws to 6-8 N·m.
(Diagram: Tightening caliper fixing screws after depressing brake lever.)
- Secure the caliper fixing screw.
Install a snap ring on the head of the screw to prevent loosening. Use only supplied snap rings.
(Diagram: Caliper fixing screw with snap ring installation.)
International-Standard Mount Type
For international-standard mounts, a dedicated adapter is required.
- Install the wheel with an attached disc brake rotor onto the frame.
- Remove the bleed spacer (yellow).
- Close the tip of the split pin.
- Remove the split pin.
- Remove the bleed spacer (yellow).
(Diagram: Brake caliper with split pin and yellow bleed spacer.)
- Set the brake pad presser spring in the brake pads.
Since there are fins on the front and rear of the finned pads, set the pads as shown in the figure. When a brake pad has markings, take note of the left (L) and right (R) markings to set it.
(Diagram: Brake pad presser spring and finned pad orientation.)
- Install the brake pads.
- Set the brake pads in the caliper.
- Insert a new split pin.
- Open the tip of the split pin.
(Diagram: Steps for installing brake pads and split pin into the caliper.)
- Temporarily install the caliper on the adapter, then install it onto the frame.
Tighten with the adapter fixing screws. Leave enough slack so the caliper can still move horizontally.
(Diagram: Caliper installation with adapter, showing temporary fixing screws for front and rear.)
- Depress the brake lever so that the disc brake rotor is held between the pads, then tighten the caliper fixing screws.
If the brake hose is not yet installed, install it first. Tighten caliper fixing screws to 6-8 N·m.
(Diagram: Tightening caliper fixing screws after depressing brake lever.)
- Secure the caliper fixing screw.
Install a snap ring on the head of the screw to prevent loosening. Use only supplied snap rings.
(Diagram: Caliper fixing screw with snap ring installation.)
Installing the Brake Hose
Overview of the Easy Hose Joint System
The easy hose joint system simplifies brake hose installation.
(Diagram: Components of the easy hose joint system including brake caliper, hose cap, flare nut, lever stopper, and brake lever.)
Checking the Length of the Hose
- Route the brake hose into the final installation position. Do not remove the hose caps from the ends of the brake hoses.
(Diagram: Bicycle with brake hoses routed.)
- Check the appropriate length of the brake hose.
Secure the brake lever in the riding position. Check the mark on the brake hose with the edge of the brake lever flare nut.
- If the hose is appropriate length, proceed to "Connecting the hose."
- If the hose needs shortening, proceed to "Cutting the hose."
- If the hose length is insufficient, replace with an appropriate length hose and proceed to "Replacing the brake hose."
(Diagram: Brake lever and hose showing appropriate length mark.)
Cutting the Hose
Use care when cutting the hose, as oil may leak.
- Determine the appropriate length and add a witness mark on the brake hose. Add the mark aligned with the edge of the flare nut.
(Diagram: Brake hose with witness mark aligned to flare nut.)
- Add a cut mark. Add a cut mark 18 mm towards the end of the hose from the witness mark. (11 mm if not using easy hose joint system).
(Diagram: Brake hose showing witness mark and cut mark with 18mm distance.)
- Disassemble the SHIMANO original tool TL-BH62. Do not move the lever before disassembling.
(Diagrams: Steps for disassembling TL-BH62 tool, showing lever, main body, press block, and hose cutter.)
- Place the brake hose in tool TL-BH62. Ensure the cut mark is parallel with the indicator groove.
(Diagram: Brake hose inserted into TL-BH62, showing cut mark alignment.)
- Check the cut location and secure the brake hose in place.
(Diagram: Securely placed brake hose in TL-BH62.)
- Check that the hose is secure, then install the hose cutter.
(Diagram: Installing the hose cutter onto the TL-BH62.)
- Press the hose cutter to cut the brake hose.
(Diagram: Operating the hose cutter to cut the brake hose.)
- Remove the hose cutter and check that the cut end is even.
(Diagram: Checking for an even, 90-degree cut on the brake hose.)
- Install the connector insert in the press block, then set the press block in tool TL-BH62. Ensure the tip of the connector insert is correctly positioned inside the opening of the brake hose.
(Diagrams: Installing connector insert into press block and then into TL-BH62.)
Note: For BL-M4100, use SHIMANO CODE No.: Y8H298040 (gold) connector insert. Using other types may cause oil leakage or malfunctions.
- Depress the lever on tool TL-BH62 to install the connector insert in the brake hose. Check for correct installation.
(Diagram: Depressing lever to install connector insert, showing correct and incorrect installations.)
- Remove the brake hose from tool TL-BH62.
(Diagram: Removing the brake hose from TL-BH62.)
Connecting the Hose
- Remove the hose cap. If the brake hose was cut, this step is not necessary.
(Diagram: Removing the hose cap.)
- Pass the hose cover over the brake hose.
(Diagram: Sliding the hose cover onto the brake hose.)
- Secure the brake lever with a tool such as a vise. Secure the hose connection port facing upward.
(Diagram: Brake lever secured in a vise with port facing up.)
- Remove the seal plug. Use a clean rag to catch any dripping oil.
(Diagram: Removing the seal plug from the brake lever.)
- Insert the brake hose in the brake hose connection port. The lever comes with a pre-installed olive. Ensure it doesn't snag. Insert the hose up to the witness mark on the outer casing. Cover with a clean rag to catch oil.
(Diagram: Inserting brake hose into connection port, showing witness mark.)
- Tighten the flare nut. Tighten to 5-7 N·m.
(Diagram: Tightening the flare nut on the brake lever.)
- Wipe off any residual oil and install the hose cover.
- Remove the lever stopper from the brake lever. Pull out with short back and forth movements, avoiding depressing the lever.
(Diagram: Removing the lever stopper from BL-M6100 and BL-M4100 levers.)
- Check that the pad spacer is installed in the caliper.
- Operate the brake lever several times. Check that the brake pads grip the pad spacer and the lever becomes stiff.
If the lever does not become stiff, refer to "Adding SHIMANO genuine mineral oil and bleeding air" to bleed the air from the system.
Operating (Adjusting the Reach)
Adjusting the reach allows you to customize the distance between the brake lever and the handlebar.
- Turn the adjustment screw to adjust the reach.
Tightening the adjustment screw (clockwise) widens the distance, while loosening (counterclockwise) narrows it.
(Diagram: BL-M6100 and BL-M4100 levers showing the reach adjustment screw and its effect on lever position.)
Maintenance
Replacing the Brake Pads
Replace brake pads if:
- Oil adheres to them.
- They are worn down to 0.5 mm thickness or less.
- The brake pad presser spring interferes with the disc brake rotor.
- Remove the wheel from the frame.
- Remove the brake pads.
- Close the tip of the split pin.
- Remove the split pin.
- Remove the brake pads from the caliper.
(Diagram: Steps for removing brake pads and split pin from the caliper.)
- Clean the pistons and the surrounding area.
- Push the pistons straight back as far as they will go. Use a flat-shaped tool, being careful not to twist or damage them.
(Diagram: Pushing pistons back into the caliper.)
- Set a brake pad presser spring in the new brake pads. Orient finned pads as shown in the figure. Note L/R markings if present.
(Diagram: Brake pad presser spring and finned pad orientation.)
- Install the brake pads.
- Set the brake pads in the caliper.
- Insert a new split pin.
- Open the tip of the split pin.
- Install the pad spacer (red).
(Diagram: Steps for installing new brake pads, split pin, and pad spacer.)
- Depress the brake lever a few times and make sure that the lever operation becomes stiff.
- Remove the pad spacer and install the wheel.
- Check that the disc brake rotor does not interfere with the brake pads. If there is interference, loosen the fixing screw and adjust until there is no more interference.
SHIMANO Genuine Mineral Oil Replacement
It is recommended to change your oil when the oil in the reservoir tank becomes noticeably discolored. Dispose of used oil according to local regulations.
Draining the Mineral Oil
- Position the bicycle as shown in the figure. Install a bleed spacer (yellow) to the caliper and secure the bicycle with a stand.
(Diagram: Bicycle positioned for mineral oil draining, showing brake hose and caliper.)
- Set the brake lever so that it is parallel to the ground.
(Diagram: Brake lever set parallel to the ground.)
- Remove the bleed screw and O-ring.
(Diagram: Removing the bleed screw and O-ring.)
- Install a bag and tube on the bleed boss / bleed nipple.
- BR-M6100 / BR-MT410: Place a 3 mm hexagon wrench. Remove the bleed boss cap and connect a tube with bag to the bleed boss.
(Diagram: Connecting tube and bag to bleed boss for BR-M6100 / BR-MT410.)
- BR-M6120: Place a 7 mm box wrench.
(Diagram: Connecting tube and bag to bleed nipple for BR-M6120.)
- BR-M6100 / BR-MT410: Place a 3 mm hexagon wrench. Remove the bleed boss cap and connect a tube with bag to the bleed boss.
- Loosen the bleed screw / bleed nipple. Oil will begin to drain. Operating the brake lever will help drain oil more easily.
(Diagram: Draining oil from bleed boss/nipple for BR-M6100 / BR-MT410 and BR-M6120.)
Adding SHIMANO Genuine Mineral Oil and Bleeding Air
Use only SHIMANO genuine mineral oil. For bleeding air, you will need the SM-DISC (oil funnel and oil stopper).
- Position the bicycle as shown in the figure. Install a bleed spacer (yellow) to the caliper and secure the bicycle with a stand.
(Diagram: Bicycle positioned for mineral oil addition, showing brake hose and caliper.)
- Set the brake lever so that it is parallel to the ground.
(Diagram: Brake lever set parallel to the ground.)
- Remove the bleed screw and O-ring, and insert the oil funnel. Do not insert the oil stopper yet.
(Diagram: Removing bleed screw and O-ring, then inserting oil funnel.)
- Add the oil through the bleed boss / bleed nipple. Do not depress and release the lever repeatedly. This can trap air bubbles.
- BR-M6100 / BR-MT410: Place a 3 mm hexagon wrench. Remove the bleed boss cap, fill syringe with oil, connect tube to bleed boss. Loosen bleed screw by 1/8 turn. Push syringe piston to add oil. Continue until no air bubbles come from the oil funnel.
(Diagram: Adding oil via syringe to bleed boss for BR-M6100 / BR-MT410.)
- BR-M6120: Place a 7 mm box wrench. Fill syringe with oil, connect tube to bleed nipple. Loosen bleed nipple by 1/8 turn. Push syringe piston to add oil. Continue until no air bubbles come from the oil funnel.
(Diagram: Adding oil via syringe to bleed nipple for BR-M6120.)
- BR-M6100 / BR-MT410: Place a 3 mm hexagon wrench. Remove the bleed boss cap, fill syringe with oil, connect tube to bleed boss. Loosen bleed screw by 1/8 turn. Push syringe piston to add oil. Continue until no air bubbles come from the oil funnel.
- Once no more air bubbles are mixed in with the oil, temporarily tighten the bleed screw / bleed nipple.
(Diagram: Temporarily tightening bleed screw/nipple for BR-M6100 / BR-MT410 and BR-M6120.)
- Remove the syringe. Cover the end with a clean rag to prevent spilling.
- Bleed the air. Most remaining air bubbles can be bled by:
- BR-M6100 / BR-MT410: Place a 3 mm hexagon wrench. Connect tube with bag to bleed boss. Loosen the bleed screw. Oil and air bubbles will flow naturally into the tube.
(Diagram: Air bleeding from bleed boss for BR-M6100 / BR-MT410.)
- BR-M6120: Place a 7 mm box wrench. Connect tube with bag to bleed nipple. Loosen the bleed nipple. Oil and air bubbles will flow naturally into the tube.
(Diagram: Air bleeding from bleed nipple for BR-M6120.)
Tech Tip: Gently shake the hose or tap the reservoir tank/caliper with a non-marring screwdriver handle. Changing caliper position may also help.
- BR-M6100 / BR-MT410: Place a 3 mm hexagon wrench. Connect tube with bag to bleed boss. Loosen the bleed screw. Oil and air bubbles will flow naturally into the tube.
- As the oil level drops in the funnel, add oil to maintain the level and prevent air from entering the system.
(Diagram: Maintaining oil level in the funnel during bleeding.)
- Once no more air bubbles come from the bleed boss / bleed nipple, temporarily tighten the bleed screw / bleed nipple.
(Diagram: Temporarily tightening bleed screw/nipple for BR-M6100 / BR-MT410 and BR-M6120.)
- With the brake lever depressed, loosen and tighten the bleed screw / bleed nipple in rapid succession. Loosen and tighten for approximately 0.5 seconds each time to release air bubbles inside the caliper.
(Diagram: Rapid loosening and tightening of bleed screw/nipple for BR-M6100 / BR-MT410 and BR-M6120.)
- Repeat step 10 two to three times, then tighten the bleed screw / bleed nipple. Tighten to 4-6 N·m.
(Diagram: Final tightening of bleed screw/nipple for BR-M6100 / BR-MT410 and BR-M6120.)
- Operate the brake lever. Air bubbles will rise into the oil funnel. Continue until no more bubbles appear.
(Diagram: Operating brake lever to release air bubbles into funnel.)
- Check that the lever has become stiff. If not, repeat from step 7.
(Diagram: Illustrates loose, slightly stiff, and stiff lever feel.)
- Tilt the brake lever upwards 30° from the ground and conduct step 12. Check for remaining air bubbles.
(Diagram: Brake lever tilted 30 degrees upwards.)
- Tilt the brake lever downwards 30° from the ground and conduct step 12. Check for remaining air bubbles.
(Diagram: Brake lever tilted 30 degrees downwards.)
- Set the brake lever so that it is parallel to the ground.
- Plug the oil funnel with the oil stopper. Ensure the O-ring side faces downward.
(Diagram: Plugging oil funnel with oil stopper.)
- Remove the oil funnel with the oil stopper still in place. Cover the bleed port with a clean rag to absorb excess oil.
(Diagram: Removing oil funnel with stopper.)
- Tighten with a bleed screw to which an O-ring has been attached. Tighten until oil flows out, ensuring no air bubbles remain. Do not operate the brake lever. Tighten to 0.5-1 N·m.
(Diagram: Tightening bleed screw with O-ring.)
- Wipe away any oil that has overflowed.
(Diagram: Wiping off overflowed oil.)
Replacing the Brake Hose
After replacing the brake hose, refer to the "SHIMANO genuine mineral oil replacement" section to inject mineral oil and bleed the air from the system.
Checking the Hose Length and Cutting the Hose
- Route the brake hose into the final installation position.
(Diagram: Bicycle with brake hoses routed.)
- After determining the appropriate length, add a witness mark on the brake hose. Add marks to both the brake lever side and caliper side.
(Diagram: Brake hose with witness marks on both lever and caliper sides.)
- Cut the brake hose. Refer to "Cutting the hose" in the "Installing the brake hose" section for detailed cutting instructions.
Assembly to the Brake Lever
- Pass the cover, flare nut, and olive over the brake hose in the order shown.
(Diagram: Order of cover, flare nut, and olive on brake hose.)
- Check that the olive is in the correct position, then apply Premium Grease to the threads of the flare nut and outer surface of the olive.
(Diagram: Olive position and grease application points.)
- Install the brake hose in the brake lever. Insert the hose up to the witness mark on the outer hose casing.
(Diagram: Inserting brake hose into brake lever, showing witness mark.)
- Tighten the flare nut while pushing on the brake hose. Tighten to 5-7 N·m.
(Diagram: Tightening flare nut on brake lever.)
- Install the cover.
(Diagram: Installing the cover over the flare nut.)
Assembly to the Brake Caliper (Straight Type)
- Pass the flare nut and olive over the brake hose in the order shown.
(Diagram: Order of flare nut and olive on brake hose for caliper assembly.)
- Check that the olive is in the correct position, then apply Premium Grease to the threads of the flare nut and outer surface of the olive.
(Diagram: Olive position and grease application points.)
- Install the brake hose in the caliper. Insert the hose up to the witness mark on the outer hose casing.
(Diagram: Inserting brake hose into caliper, showing witness mark.)
Note: Do not let the brake hose become twisted. Ensure no twist if caliper and brake lever are in the positions shown in the figure.
(Diagram: Caliper and brake lever positions to check for hose twist.)
- Tighten the flare nut while pushing on the brake hose. Tighten to 5-7 N·m.
(Diagram: Tightening flare nut on caliper.)
Caliper Piston Maintenance
Adjust pistons if they do not operate properly, protrude unevenly, or if brake pads contact the disc brake rotor.
- Remove the wheel from the frame.
- Remove the brake pads.
- Close the tip of the split pin.
- Remove the split pin.
- Remove the brake pads from the caliper.
(Diagram: Steps for removing brake pads and split pin from the caliper.)
- Clean the pistons and the surrounding area.
- Push the pistons straight back as far as they will go. Use a flat-shaped tool, being careful not to twist or damage them.
(Diagram: Pushing pistons back into the caliper.)
- Install the brake pads.
- Set the brake pads in the caliper.
- Insert a new split pin.
- Open the tip of the split pin.
- Install the pad spacer (red).
(Diagram: Steps for installing new brake pads, split pin, and pad spacer.)
- Operate the brake lever through its full range of travel and depress it several more times so that the pistons move to their initial positions.
- Remove the pad spacer and install the wheel.
- Check that the disc brake rotor does not interfere with the brake pads. If there is interference, loosen the fixing screw and adjust until there is no more interference.
Troubleshooting
This section addresses common issues you might encounter with your hydraulic disc brake system.
- Brake lever feels spongy or lacks power: This often indicates air in the hydraulic system. Refer to the "Adding SHIMANO Genuine Mineral Oil and Bleeding Air" section for bleeding instructions.
- Brake fluid leaking: Check all connections (flare nut, hose joints) for proper tightening. Ensure the brake hose is cut perpendicularly. If the olive or connector insert is reused, replace them.
- Brake pads rubbing on disc rotor: This can be caused by misaligned calipers, warped rotors, or pistons not fully retracting. Re-align the caliper (see "Installing the Brake Caliper" section) or perform caliper piston maintenance. Check rotor for warping and replace if necessary.
- Brake pads worn out: If brake pad thickness is 0.5 mm or less, replace them immediately. See "Replacing the Brake Pads" section.
- Disc brake rotor is cracked, deformed, or too thin: Replace the disc brake rotor immediately. Do not use if thickness is 1.5 mm or less or if the aluminum surface is visible.
- Brake lever stroke increases continuously: This can be a sign of air in the system or fluid issues. Perform mineral oil replacement and bleeding.
- Brakes not operating effectively after contact with oil/grease: Clean the disc brake rotor and pads thoroughly with isopropyl alcohol. If pads are contaminated, they may need replacement.
- Difficulty pushing pistons back: Ensure bleed screws are loosened to relieve pressure. Use a flat-shaped tool carefully.
Specifications
| Attribute | Value |
|---|---|
| Brand Name | SHIMANO |
| Model Number | BL-M4100 |
| Braking System | Hydraulic Disc Brake (Hydraulic Brake Pad) |
| Components | Levers |
| High-concerned chemical | None |
| Origin | MY (Malaysia) |
| Lever size (finger) | 2 |
| Brake hose (kit) | SM-BH59-JK-SS (for BR-MT410), SM-BH90-SS (for BR-MT420) |
| Hose joint | Straight |
| Clamp band | Open clamp |
| Weight | 113g/pc |
User Tips
No specific user tips were available from provided reviews or Q&A content. However, based on general best practices for hydraulic disc brakes:
- Regularly check brake pad wear and replace them before they reach the minimum thickness.
- Keep your brake system clean, especially the rotors and pads, to ensure optimal performance.
- Periodically check for any signs of fluid leaks around the levers and calipers.
- If you notice a change in brake feel (e.g., spongy lever), it's likely time for a brake bleed to remove air from the system.
- Always use genuine Shimano mineral oil for maintenance to ensure compatibility and performance.
Warranty and Support
For warranty information and support, please contact your place of purchase or a Shimano distributor. Specifications are subject to change for improvement without notice.
Shimano Contact Information:
- SHIMANO NORTH AMERICA BICYCLE, INC.
One Holland, Irvine, California 92618, U.S.A.
Phone: +1-949-951-5003 - SHIMANO EUROPE B.V.
High Tech Campus 92, 5656 AG Eindhoven, The Netherlands
Phone: +31-402-612222 - SHIMANO INC.
3-77 Oimatsu-cho, Sakai-ku, Sakai City, Osaka 590-8577, Japan
A PDF version of the user manual is available for download from the official Shimano website: https://si.shimano.com (refer to document DM-MBDBR01-01).
Product Video
Watch an unboxing and overview of the Shimano BL-M4100 Brake Lever: