diymore RX5808

Contents

RX5808 4.9G-5.8G Audio Video Receiver Module User Manual

Model: RX5808 | Brand: diymore

1. Introduction

The diymore RX5808 is a compact 4.9GHz to 5.8GHz wireless audio and video receiving module designed for FPV systems, RC applications, and various DIY electronic projects. It supports both SPI control and switch control methods for channel selection, offering flexibility for integration into different systems. This module provides reliable performance with low power consumption and high accuracy, making it suitable for demanding wireless video transmission tasks.

Video: Overview of the RX5808 Receiver Module.

2. Setup and Connections

Proper connection of the RX5808 module is crucial for its operation. Refer to the pinout diagram below for detailed wiring instructions. The module comes in different variants (SPI control with/without audio, Switch control with/without audio), but the core pinout remains consistent for power and A/V output.

RX5808 Module Pinout Diagram

Image: RX5808 Module Pinout and Type Identification. This diagram shows the front and back of the module with all pin labels.

2.1 Pin Description

Pin NameDescription
GNDGround connection.
VIDEOVideo output signal.
AUDIOAudio output signal (available on "with audio" variants).
RSSIReceived Signal Strength Indicator output.
+5VPower supply input (5V). Note: Module operates at 3.3V internally, but 5V input is common.
CH3/CLKChannel selection pin 3 (for switch control) or SPI Clock (for SPI control).
CH2/LEChannel selection pin 2 (for switch control) or SPI Latch Enable (for SPI control).
CH1/DATAChannel selection pin 1 (for switch control) or SPI Data (for SPI control).
ANTAntenna connection point.

2.2 Power Supply

Connect the +5V pin to a stable 5V DC power source and the GND pin to the system ground. Ensure the power supply can provide at least 170mA.

2.3 Antenna Connection

Solder a 50-ohm antenna directly to the ANT pad on the module. Ensure a good solder joint for optimal signal reception.

3. Operating Instructions

The RX5808 module supports two primary methods for channel selection: SPI control and Switch control. The method used depends on the specific variant of your module.

3.1 SPI Control (SPI Module Variants)

For SPI-controlled modules, channel selection is managed by sending commands via a microcontroller (e.g., Arduino, ESP32) connected to the CLK, LE, and DATA pins. You will need to implement the appropriate SPI communication protocol in your microcontroller's firmware to select the desired receiving frequency.

3.2 Switch Control (Switch Control Module Variants)

For switch-controlled modules, channels are typically selected by setting the logic levels (HIGH/LOW) on the CH1, CH2, and CH3 pins. This can be done using physical switches, jumpers, or GPIO pins from a microcontroller. Consult the module's datasheet or common RX5808 channel tables for the specific logic combinations corresponding to each frequency.

3.3 Audio and Video Output

Once powered and a channel is selected, the module will output the received video signal on the VIDEO pin and the audio signal on the AUDIO pin (if it's an audio-enabled variant). Connect these outputs to your display device or video processing unit.

4. Maintenance

The RX5808 module is a robust electronic component with minimal maintenance requirements.

  • Keep Dry: Protect the module from moisture and humidity to prevent corrosion and short circuits.
  • Avoid Static Discharge: Handle the module with care, especially in dry environments, to prevent damage from electrostatic discharge (ESD).
  • Cleanliness: Keep the module free from dust and debris. Use a soft, dry brush or compressed air for cleaning if necessary.
  • Physical Protection: Avoid physical stress or impact that could damage the delicate components or solder joints.

5. Troubleshooting

If you encounter issues with your RX5808 module, consider the following troubleshooting steps:

  • No Video/Audio Output:
    • Verify power connections (+5V and GND) are correct and stable.
    • Ensure the antenna is properly connected.
    • Check that the transmitting and receiving channels are matched.
    • Confirm the video/audio output pins are correctly connected to your display.
    • If using SPI control, verify your microcontroller code is correctly setting the channel.
    • If using switch control, ensure the CH1/CH2/CH3 pins are set to the correct logic levels.
  • Poor Signal Quality:
    • Check antenna type and orientation on both transmitter and receiver.
    • Ensure there are no obstructions between the transmitter and receiver.
    • Reduce the distance between the transmitter and receiver.
    • Check for sources of interference (e.g., Wi-Fi, other wireless devices).
    • Verify power supply is clean and free of noise.
  • Module Not Powering On:
    • Double-check power supply voltage (must be 5V).
    • Ensure GND connection is solid.
    • Inspect for any visible damage to the module.

6. Specifications

ParameterValue
Receiving Frequency5645 - 5945 MHz
Receiving Sensitivity-90 dBm
Power Consumption5V @ 170 mA
Power Supply Voltage3.3 V (Internal operation, typically 5V input)
Supply Current170 mA
Dimensions (L x W x H)28 mm x 23 mm x 3 mm
RX5808 Module Dimensions

Image: RX5808 Module Dimensions. The image shows the length (28mm/1.10in) and width (23mm/0.91in) of the module.

7. User Tips

  • FPV Integration: This module is commonly used in FPV (First Person View) drone systems. Ensure compatibility with your video transmitter and FPV goggles/display.
  • Test Before Final Assembly: It's recommended to test the module's functionality and signal reception before permanently integrating it into your project.
  • Clean Power: Provide a clean, stable power supply to the module to minimize noise in the video and audio output.
  • Antenna Quality: Use a good quality 5.8GHz antenna for optimal range and signal clarity.

8. Warranty and Support

For any technical assistance or support regarding the diymore RX5808 module, please contact your retailer or the manufacturer directly. Keep your purchase records handy for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.