Important Safety Instructions
Safety Information
To ensure safe use and avoid fire, explosion or personal injury, read and follow all safety instructions carefully before using this product. Keep this manual for future reference.
WARNING: Fire & Explosion Hazards
- Keep this product away from open flames, high-temperature sources (above 100°C) and open fire operation to prevent fuel leakage and fire/explosion hazards caused by high temperature.
- Fuel leakage will cause fire and explosion hazards; do not use the switch if the sealing is not tight, the valve core is loose or the switch is damaged. Stop the engine immediately and cut off the oil circuit if fuel leakage is found.
WARNING: Choking & Ingestion Risks
- This product is exclusively for gasoline engine fuel tank oil circuit control and must be installed and used in accordance with the model and specification requirements.
- Keep the product and its small accessories (gaskets, screws, nuts, etc.) out of reach of children to avoid choking, ingestion or fire risks caused by contact with flammable substances.
- Plastic packaging can cause suffocation. Keep it away from children. Do not use the packaging as a toy.
WARNING: Modification & Disassembly
- Unauthorized disassembly, modification, drilling or welding of the switch body, valve core, oil inlet/outlet or sealing parts will void the warranty and may damage the sealing structure, cause fuel leakage and lead to fire, explosion or mechanical failure of the engine.
- For product maintenance, replacement or repair, contact our customer service only.
- Do not disassemble, install or adjust the switch when the engine is running or the fuel tank is full of gasoline; ensure the engine is cooled and the fuel in the oil circuit is drained before any operation.
ATTENTION
- Not suitable for installation or operation by untrained personnel or children.
CAUTION: Environmental & Usage Conditions
- Avoid installing or using the product in rainy, snowy, dusty or high-humidity environments; take waterproof and dustproof measures to prevent water and dust from entering the switch and causing valve core jamming or oil circuit blockage.
- Read these instructions carefully and retain them for future reference.
- Do not use the product on engines or fuel tanks with unmatched specifications (caliber, pressure, fuel type); only applicable to gasoline fuel, not for diesel, kerosene or other flammable and explosive liquids.
- Do not use excessive force to rotate the switch handle; operate it gently to avoid damage to the valve core, thread or sealing ring and cause fuel leakage.
- Avoid strong impact, collision or scratch to the switch body and handle during transportation, installation and use; prevent sharp objects from piercing the sealing parts to avoid oil leakage.
- Do not use the product if the switch body is cracked, deformed, the handle is loose, the sealing ring is aging/cracking or the thread is damaged; replace the whole switch or damaged genuine parts in a timely manner.
- Keep the product clean and dry at all times; do not soak the switch in water or other liquids for a long time, and avoid contact with corrosive chemicals (such as acid, alkali, solvent) to prevent metal rusting and rubber sealing part aging.
SAVE THESE INSTRUCTIONS
Setup
Pre-use Preparation
- Before first use, wipe the switch body, oil inlet/outlet, thread and sealing gaskets with a clean dry soft cloth to remove dust, anti-rust oil and processing residues during production and transportation; do not use alcohol, gasoline or other flammable solvents for cleaning.
- Check the integrity of the product: confirm no cracking, deformation or scratch of the switch body, the handle rotates smoothly without jamming, the sealing ring is intact (no aging, cracking, hardening), the thread is complete without damage, and all accessories are complete; do not use defective products.
- Prepare professional installation tools (wrench, tape measure, thread sealant), check the gasoline engine fuel tank oil outlet and oil circuit pipeline for no damage, deformation or oil leakage, and confirm the oil outlet caliber and thread specification match the switch.
- Prepare genuine sealing gaskets and thread sealant (Teflon tape) matching the switch; ensure the sealant is resistant to gasoline and high temperature to avoid dissolution and oil leakage.
Installation
The fuel tap is designed for easy installation. Ensure the engine is cool and the fuel tank is empty or at a low level before beginning. Follow these general steps:
- Locate the existing fuel tap or the designated mounting point on your fuel tank.
- Carefully remove the old fuel tap (if applicable), ensuring no fuel spills.
- Apply thread sealant (Teflon tape) to the threads of the new CENJITION fuel tap.
- Insert the fuel tap into the fuel tank outlet and tighten it securely with a wrench. Do not overtighten.
- Connect the fuel line to the outlet nozzle of the fuel tap. Ensure the connection is secure and free from leaks.
- After installation, check for any fuel leaks by slowly adding fuel to the tank and observing the connections.

Figure 1: Front view of the CENJITION NH-255 Fuel Tap, showing the lever and fuel markings.

Figure 2: Dimensions of the CENJITION NH-255 Fuel Tap (approx. 8cm length, 4cm height).
Operating Instructions
The CENJITION NH-255 fuel tap features a simple lever mechanism to control fuel flow to your engine.
- ON Position: Rotate the lever to the "ON" position to allow fuel to flow from the tank to the engine. This is the standard operating position.
- OFF Position: Rotate the lever to the "OFF" position to stop the fuel flow. This position should be used when the vehicle is parked for extended periods, during maintenance, or for transport to prevent fuel leakage.
- FUEL (Reserve) Position: Some fuel taps may have a "FUEL" or "RES" position, typically indicating a reserve fuel supply. For this model, the primary positions are ON and OFF.
Always ensure the lever is fully engaged in the desired position to prevent partial fuel flow or leakage.

Figure 3: CENJITION NH-255 Fuel Tap installed on a motorcycle.
Maintenance
- Cleaning: Keep the product clean and dry at all times. Regularly wipe the exterior with a clean, dry cloth.
- Avoid Immersion: Do not soak the switch in water or other liquids for a long time.
- Chemical Exposure: Avoid contact with corrosive chemicals (such as acid, alkali, solvent) to prevent metal rusting and rubber sealing part aging.
- Professional Service: For any product maintenance, replacement, or repair beyond simple cleaning, contact customer service or a qualified mechanic. Do not attempt unauthorized repairs or modifications.
Troubleshooting
- Fuel Leakage: If fuel leakage is observed, immediately stop the engine and cut off the oil circuit. Do not use the switch if the sealing is not tight, the valve core is loose, or the switch is damaged. Replace the unit if necessary.
- No Fuel Flow: Ensure the fuel tap is in the "ON" position. Check the fuel line for kinks or blockages. Verify that the fuel tank has sufficient fuel. If the issue persists, the tap may be clogged or faulty and require replacement.
- Physical Damage: Do not use the product if the switch body is cracked, deformed, the handle is loose, the sealing ring is aging/cracking, or the thread is damaged. Replace the entire switch or damaged genuine parts in a timely manner to prevent further issues.
Specifications
| Model Name | NH-255 |
| Hose Diameter | 6mm |
| Material | Plastic and Metal |
| Dimensions (Approx.) | Length: 8cm, Height: 4cm |
| Item Weight (Approx.) | 80g |
| Origin | Mainland China |
| High-concerned Chemical | None |
User Tips
- Compatibility Check: Before purchasing and installing, verify that this 6mm fuel tap is compatible with your specific motorcycle or scooter model. Users have reported successful installation on models like the Peugeot Elyseo 50.
- Secure Installation: Always ensure the fuel tap is installed securely with appropriate thread sealant and gaskets to prevent any leaks. A proper seal is crucial for safety and performance.
- Regular Inspection: Periodically inspect the fuel tap and fuel lines for any signs of wear, damage, or leaks to ensure safe operation.
Warranty & Support
After-Sales Service
If you have any questions or encounter issues during the purchase process or after receiving your CENJITION NH-255 fuel tap, please do not hesitate to contact the seller directly. The seller is committed to providing the best after-sales service and will work to resolve any concerns you may have.
Manufacturer Information
Manufacturer: Yiwu Lalang Electronic Technology Co., Ltd
Address: 4th Floor, No. 100 Chengdian Road, Choujiang Street, Yiwu City, Jinhua City, Zhejiang Province
European Representative (for compliance inquiries):
Company: QTEC EUREP GMBH
Address: Curtiusstrasse 27, Schleswig-Holstein, Lübeck, Germany
Phone: 01764603460