HM Digital COM-300, PH-200, ORP-200

Contents

HM Digital Water Quality Meter User Manual

Models: COM-300 (4-in-1), PH-200 (2-in-1), ORP-200 (2-in-1)

I. Product Overview

The HM Digital Water Quality Meter is a device designed to detect various water quality parameters in aquatic environments, providing accurate and efficient water quality monitoring services. This manual details the usage methods, precautions, and maintenance procedures for the water quality monitor, assisting users in correctly operating and maintaining the equipment.

The meters are available in different configurations:

  • HM COM-300: Measures pH, EC (Electrical Conductivity), TDS (Total Dissolved Solids), and Temperature.
  • HM PH-200: Measures pH and Temperature.
  • HM ORP-200: Measures ORP (Oxidation-Reduction Potential) and Temperature.
Three HM Digital water quality meters: ORP-200 (green cap), COM-300 (black cap), and PH-200 (orange cap).
Overview of HM Digital Water Quality Meter models: ORP-200, COM-300, and PH-200.

II. Setup

1. Preparatory Work

Before commencing use of the water quality monitor, inspect the equipment for any damage. Ensure the instrument has been calibrated. Simultaneously, install fresh batteries into the instrument, connect it to a power source (if applicable), and ensure the power supply is stable.

2. Battery Installation

The meters require 2 AAA batteries (not included). To install:

  1. Unscrew the battery case cap located at the top of the meter.
  2. Insert two AAA batteries, ensuring correct polarity.
  3. Securely screw the battery case cap back on.
Close-up of the HM COM-300 battery compartment showing two AAA batteries being inserted.
Battery compartment design for HM COM-300, showing insertion of 2 AAA batteries.
HM PH-200 with the battery cap open, showing two AAA batteries being inserted.
Battery installation for HM PH-200.
HM ORP-200 with the battery cap open, showing two AAA batteries being inserted.
Battery installation for HM ORP-200.

III. Operating Instructions

1. General Testing Procedure

  1. Switch On: Press the 'ON/OFF' button to switch on the instrument. The system will automatically initialize and display the main interface.
  2. Select Parameter (COM-300): For the COM-300 model, press the 'MODE' button to cycle through pH, TDS, and EC modes. The selected mode will be displayed on the screen.
  3. Immerse Sensor: Immerse the sensor section of the water quality monitor into the water sample to be tested, ensuring full contact between the sensor and the water.
  4. Read Results: Wait a few seconds for the reading to stabilize. The instrument will automatically measure and display the test results along with the temperature.
  5. Hold Function: Press the 'HOLD' button to freeze the current reading on the display for easier recording. Press again to release.
  6. Temperature Unit: Press the 'TEMP/CAL' button to switch between Celsius (°C) and Fahrenheit (°F) temperature units.
HM COM-300 meter displaying EC, TDS, and PH readings with temperature, labeled 'ONE KEY TEST, THREE TEST MODES'.
HM COM-300 displaying EC, TDS, and PH modes with temperature.
HM COM-300 water quality meter showing its functions: PH, EC, TDS, and TEMP.
HM COM-300 highlighting its PH, EC, TDS, and Temperature measurement capabilities.

2. Calibration

The meters feature a digital calibration function for simple and accurate calibration. For pH, press the calibration button to 4, 7, or 10 pH. For EC/TDS, calibration is via button to any point within the range.

It is recommended to recalibrate the device periodically or if readings appear inaccurate.

3. Automatic Temperature Compensation (ATC)

All models are equipped with Automatic Temperature Compensation (ATC) to adapt to naturally occurring temperature differences, ensuring measurement results are not affected by changes in water temperature.

HM PH-200 demonstrating automatic temperature compensation with thermometer icons showing temperature changes not affecting measurement.
Automatic temperature compensation ensures accurate readings despite temperature fluctuations.

IV. Maintenance

1. Operating Environment

The water quality monitor is intended for indoor use only. Avoid exposure to direct sunlight or adverse weather conditions. Additionally, refrain from using it near pollution sources to prevent interference with test results.

2. Sensor Maintenance

Maintaining the cleanliness of the sensor assembly is crucial for ensuring accurate measurements. After each use, clean the sensor using appropriate methods to ensure its surface remains free of contaminants.

For ORP meters, wipe the platinum band back and forth on both sides with a piece of 3.5 mm extra fine, soft touch sandpaper.

Diagram showing how to clean the platinum band of an ORP meter electrode using sandpaper.
Cleaning the ORP meter electrode's platinum band.

3. Power Management

Regularly check battery levels. Remove batteries during prolonged periods of non-use. Should a low-battery warning occur during operation, promptly replace the batteries.

4. Impact Prevention

As a precision instrument, the water quality monitor must be protected from impacts, drops, or compression during use to prevent damage.

V. Troubleshooting

Below are common faults and their suggested solutions:

  1. Display shows garbled characters or no display: Check the instrument's battery level and attempt to restart the device.
  2. Inaccurate or unstable test results: First, verify that the sensor is clean and functioning correctly. If necessary, recalibrate the device and ensure the measurement environment is stable.
  3. Instrument fails to power on: Confirm that the power supply is properly connected. If using batteries, ensure they are fully charged or replace them before attempting to power on again.

VI. Specifications

HM COM-300 (4-in-1)

Parameter Specification
PH Range0.0-14.0 PH
EC Range0-9990 μS; 0-9.99 mS
TDS Range0-8560 ppm (0.7 Scale); 0-5000 ppm (0.5 Scale)
Temperature Range0-55 °C; 32-122°F
PH Resolution0.1PH
EC Resolution0-999: 0.1 μS, 1000-9990: 10 μS, 0-9.99mS: 0.01mS
TDS Resolution0-999: 1 PPM, 1000-9990: 10 PPM
Temperature Resolution0.1 °C/°F
Accuracy+/- 2%, Temp: +/- 1°C/°F
EC/TDS Conversion FactorPreprogrammed nonlinear conversion of 0.5 (NACL) or 0.7 (442TM) solution, selected by user
Temperature CompensationAutomatic (ATC) to 25 °C (ATC range: 1-50 °C)
CalibrationDigital calibration via button (to any point within the range)
Automatic ShutdownAfter 5 minutes
ProbeDetachable electrode
Display ScreenLCD panel
ShellIP-67 waterproof
Power Supply2 AAA batteries
Product Dimension18.5 x 3.4 x 3.4 cm
Item Weight187g

HM PH-200 (2-in-1)

Parameter Specification
MeasurespH, Temperature
pH Range0-14 pH
Temperature Range0.1-55 °C, 32-130 °F
pH Resolution0.01PH
Temperature Resolution0.1°C/°F
Accuracy0-0.1PH
ATCYes
CalibrationAuto-calibration
Power Supply2 AAA batteries (not included)
Size18.5 x 3.4 x 3.4 cm

HM ORP-200 (2-in-1)

Parameter Specification
MeasuresORP, Temperature
ORP Range-999 to +1000 mV
Temperature Range0-80°C; 32-176°F
ORP Resolution1 mV
Temperature Resolution0.1°C/°F
Accuracy0.5% (+/-2mV)
ATCYes
CalibrationDigital calibration by push button
ElectrodeReplaceable glass sensor and reference tube electrodes
HousingIP-67 Waterproof (submersible; floats)
Power Supply2 AAA batteries (not included)
Dimensions18.5 x 3.4 x 3.4 cm (7.3 x 1.3 x 1.3 inches)
Weight96.4 g (3.4 oz)

VII. User Tips

  • Always ensure the sensor is clean before and after each use to maintain accuracy.
  • Store the meter with the protective cap on to prevent damage to the electrode.
  • If readings seem off, try recalibrating the device with fresh calibration solutions.
  • Avoid exposing the meter to extreme temperatures or direct sunlight for prolonged periods.

VIII. Warranty and Support

For any questions or issues not covered in this manual, please contact customer support. Keep your purchase receipt for warranty claims.

A user manual in PDF format is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.