1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your M.2 NGFF B Key to 2.5inch SATA SSD Enclosure. This device allows you to convert an M.2 NGFF (SATA interface) solid-state drive into a standard 2.5-inch SATA hard disk drive, making it suitable for use in laptops, desktops, or as an external storage solution.
2. Safety & Warnings
Please read all instructions carefully before using this product. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
3. Package Contents
Verify that all items are present in your package:
- 1 x SATA to NGFF M.2 B-Key SSD Hard Drive Case
- 4 x M.2 Black Screws
- 2 x M.2 Screws
- 1 x Bracket

4. Specifications
| Feature | Description |
|---|---|
| Product Type | M.2 NGFF B Key to 2.5inch SATA SSD Enclosure |
| Origin | Mainland China |
| Supported SSD Interface | M.2 NGFF (SATA interface) B Key SSDs |
| Supported SSD Sizes | 22x30mm, 22x42mm, 22x60mm, 22x80mm |
| Output Interface | 2.5-inch SATA I/II/III |
| Data Transfer Speed | Up to 6Gbps (SATA III) |
| Product Dimensions | 100.00 x 70.00 x 10.00 mm (3.94 x 2.76 x 0.39 inches) |
| Color | Black |
| Compatibility Note | Does NOT support M.2 Key M PCI-E Bus SSD. |

5. Setup & Installation
Follow these steps to install your M.2 NGFF B Key SSD into the enclosure:
- Prepare the Enclosure: Open the 2.5-inch SATA SSD enclosure.
- Identify SSD Compatibility: Ensure your M.2 SSD is an NGFF (SATA interface) B Key type and matches one of the supported sizes (22x30mm, 22x42mm, 22x60mm, 22x80mm). This enclosure does not support M.2 Key M PCI-E Bus SSDs.
- Insert the M.2 SSD: Carefully align your M.2 NGFF B Key SSD with the M.2 slot on the adapter board and insert it firmly. The B Key connector has 6 pins on the shorter side.
- Secure the SSD: Use the provided M.2 screws to secure the SSD to the adapter board at the appropriate length (2230, 2242, 2260, or 2280).
- Assemble the Enclosure: Place the adapter board with the installed SSD into the 2.5-inch enclosure. Close the enclosure and secure it with the remaining screws.




6. Operating Instructions
Once your M.2 SSD is securely installed in the enclosure, it functions as a standard 2.5-inch SATA drive.
- Connection: Connect the 2.5-inch SATA interface of the enclosure to a compatible SATA port on your laptop, desktop, or external SATA dock using a standard SATA data and power cable (not included).
- Plug and Play: The enclosure is plug-and-play, meaning no additional drivers are typically required for most operating systems. Your system should detect the drive automatically.
- Data Transfer: Enjoy high-speed data transfer rates up to 6Gbps, depending on your SSD and host system's SATA capabilities.
- TRIM Function: For optimal performance and longevity of your SSD, ensure the TRIM function is enabled. Most modern operating systems automatically support and enable TRIM for SSDs.
- Security: If your SSD supports encryption (such as AES), you can enable this feature through your operating system or SSD management software to protect sensitive information.
7. Maintenance
- Data Backup: Regularly back up important data from your SSD to prevent data loss.
- Physical Handling: Avoid frequent plugging and unplugging of the hard disk to reduce mechanical wear and tear on the connectors.
- Cleaning: Keep the enclosure clean and free from dust. Use a soft, dry cloth for cleaning. Do not use liquid cleaners.
- Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
8. Troubleshooting
- Drive Not Detected:
- Ensure the M.2 SSD is correctly seated in the adapter board and secured.
- Verify that the SATA data and power cables are securely connected to both the enclosure and the host system.
- Check if your M.2 SSD is an NGFF (SATA) B Key type. This enclosure is not compatible with M.2 Key M PCI-E Bus SSDs.
- Try connecting the enclosure to a different SATA port or a different computer to rule out port or system issues.
- Slow Performance:
- Ensure your host system's SATA port supports SATA III (6Gbps) for maximum speed.
- Check if TRIM is enabled for your SSD in your operating system.
- Verify that the SSD itself is not experiencing performance degradation.
- Physical Damage: If the enclosure or adapter board appears physically damaged, discontinue use immediately.
9. User Tips
- This product is an enclosure/adapter for M.2 NGFF (SATA) SSDs to fit into a 2.5-inch SATA bay. It includes the necessary case, adapter board, and screws for assembly. It does not include an additional separate adapter beyond the enclosure itself.
- Ideal for repurposing older M.2 SATA SSDs or upgrading laptops/desktops that only have 2.5-inch drive bays.
- Can be used for data backup, system operation (if installed as a primary drive), or general file storage.
10. Manufacturer Information
EU Authorized Representative:
- Company name: Valhalla Taxi
- Address: RUE GENERAL DE REFFYE EGD, 88000 EPINAL 913 439 188 R.C.S. Epinal
- Tel: +33(0)629986194
- Mailbox: valhallatax@outlook.com
11. Warranty & Support
For warranty information, technical support, or further inquiries, please contact your point of purchase or the manufacturer directly using the contact details provided above. Additional item guides and documents may be available in PDF format: User manual (PDF).