Aramox ANLEON S0

Contents

ANLEON S0 Monitor Amplifier User Manual

Precise Volume Control XLR Input 3.5mm Stereo Jack with Waist Clip

1. Introduction

This manual provides comprehensive instructions for the safe and effective use of your ANLEON S0 Monitor Amplifier. Designed for musicians, particularly drummers and keyboardists, this device allows for individual monitoring with precise volume control. Please read this manual thoroughly before operating the device and retain it for future reference.

2. Safety Information

Please observe the following safety guidelines to prevent injury or damage to the device:

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Avoid exposing the device to extreme temperatures, moisture, or direct sunlight.
  • Do not attempt to disassemble or modify the device. Refer all servicing to qualified personnel.

3. Product Overview

The ANLEON S0 Monitor Amplifier is a compact and robust personal monitoring solution. It features an XLR input for balanced audio signals, a 3.5mm stereo jack for headphone output, and a precise volume control knob. An integrated waist clip provides convenient portability during performances.

Key Features:

  • Designed for onstage musicians (drummers, keyboardists).
  • XLR locking socket for secure input connection.
  • Precise volume control knob.
  • 3.5mm stereo mini jack headphone output.
  • Durable aluminium alloy construction.
  • Integrated waist clip for portability.

Component Identification:

Front view of the ANLEON S0 Monitor Amplifier showing the volume knob and 3.5mm headphone jack.
Figure 1: Front view with Volume Knob and Headphone Jack
Rear view of the ANLEON S0 Monitor Amplifier showing the XLR input.
Figure 2: Rear view with XLR Input
Side view of the ANLEON S0 Monitor Amplifier highlighting the integrated waist clip.
Figure 3: Side view with Waist Clip

4. Setup

Follow these steps to set up your monitor amplifier:

  1. Unpacking: Carefully remove all protective packaging materials from the equipment.
  2. Inspection: Inspect the product for any signs of damage. If the product appears damaged, do not use it and contact support.
  3. Connect Audio Input: Connect an XLR cable from your audio source (e.g., mixing console, audio interface) to the XLR locking socket on the monitor amplifier. Ensure the connection is secure.
  4. Connect Headphones: Plug your headphones into the 3.5mm stereo jack output.
  5. Powering the Device: The device is powered via USB (5-20V DC) or an AC power source. Connect the appropriate power adapter (if included) or USB cable to power the unit.
  6. Secure with Waist Clip: If desired, attach the monitor amplifier to your belt or trouser waistband using the integrated waist clip for convenient access during performance.

5. Operation

Once the device is set up, you can begin using it for personal monitoring:

  1. Initial Volume Setting: Before playing any audio, turn the VOLUME knob counter-clockwise to its minimum setting to avoid sudden loud sounds.
  2. Play Audio: Start playing audio from your connected source.
  3. Adjust Volume: Slowly turn the VOLUME knob clockwise to increase the headphone volume to a comfortable listening level. The knob allows for precise control.
  4. Monitoring: Listen to your mix through your headphones. Adjust the volume as needed throughout your performance.

6. Maintenance

Proper care and maintenance will ensure the longevity of your monitor amplifier:

  • Cleaning: After each use, turn off the device and wipe it with a soft, dry cloth. Do not use liquid cleaners or solvents.
  • Storage: Store the device in a dry place, away from direct sunlight and extreme temperatures. Keep it away from children.
  • Cable Care: Handle cables carefully. Avoid sharp bends or kinks that could damage the internal wiring.

7. Troubleshooting

If you encounter issues with your monitor amplifier, try the following solutions:

  • No Sound:
    • Ensure the device is properly powered.
    • Check all cable connections (XLR input, headphone output) are secure.
    • Verify the volume knob is turned up.
    • Confirm the audio source is sending a signal.
    • Test with different headphones and cables to rule out faulty accessories.
  • Distorted Sound:
    • Reduce the input level from your audio source.
    • Lower the volume on the monitor amplifier.
    • Ensure your headphones' impedance is within the supported range (32-600 ohms).
  • Intermittent Sound:
    • Check for loose cable connections.
    • Inspect cables for damage.

If the problem persists, please contact customer support.

8. Specifications

Attribute Value
Product Name Monitor Amplifier
Model Number ANLEON S0 (GET.5321)
Type In-Ear Monitoring
Material Aluminium alloy
Inputs XLR, Stereo (Pin 1: GND, 2: L, 3: R)
Output 3.5mm jack, stereo
Maximum Power 100 mW
Headphone Impedance 32-600 ohms
Voltage Range USB (5-20V DC)
Power Source AC
Built-in Battery No
Inbox Adaptor Yes
Origin Mainland China
Certification CE

9. User Tips

  • For optimal sound quality, ensure your headphones have an impedance within the recommended range of 32-600 ohms.
  • Always start with the volume at its lowest setting and gradually increase it to prevent hearing damage.
  • The waist clip is designed for convenience; ensure it is securely fastened to prevent accidental drops during active use.
  • Consider using high-quality XLR and 3.5mm cables to minimize signal loss and interference.

10. Warranty & Support

For technical support, warranty claims, or further inquiries, please contact the manufacturer or authorized representative:

Manufacturer:

  • Company Name: Dongguan Shiyang Technology Co., Ltd.
  • Address: No. 1, Yindou Fourth Road, Qingxi Town, Dongguan City, Guangdong Province
  • Email: 13670101789@qq.com
  • Telephone: 86-13670101789

EU Authorized Representative:

  • Company Name: Kequ Technology s.r.o.
  • Address: Pražákova 1008/69, Štýřice, 63900 Brno, Jihomoravský kraj, Czech Republic Brno City South Moravian Region
  • Email: christopher25106@outlook.com
  • Telephone: 420-123456789

A detailed user manual in PDF format is also available for download: Download User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.