GIANTELE RO15

Contents

GIANTELE RO15 Ceramic Fast Blow Fuse Instruction Manual

Model: RO15 | Dimensions: 10x38mm | Voltage: 500V

1. Introduction

The GIANTELE RO15 10x38mm ceramic fuse tube is an overcurrent protection component designed to safeguard electrical circuits and equipment. When the current in a circuit exceeds its rated value, the internal fuse element melts, opening the circuit to prevent damage to connected devices and wiring. Its ceramic housing provides high temperature resistance, impact resistance, and high breaking capacity, making it suitable for demanding applications.

These fuses are commonly used in industrial equipment, power systems, photovoltaic inverters, charging stations, and other circuits where reliable overcurrent protection and high breaking capacity are essential.

2. Safety Information

Always prioritize safety when working with electrical components. Failure to follow these instructions may result in electric shock, injury, or equipment damage.

  • Disconnect Power: Always disconnect the equipment power by unplugging it or turning off the main switch before attempting to replace a fuse.
  • Correct Specifications: Use only a fuse tube with the exact same specifications (rated current, voltage, and breaking capacity) as the original. Never substitute with copper wire, iron wire, or ordinary glass fuses.
  • Circuit Faults: If a replacement fuse blows immediately, it indicates a likely fault in the circuit. Identify and correct the fault before installing another fuse. Do not blindly use a higher current rating, as this can lead to severe damage or fire.
  • Avoid Live Contact: Do not touch both ends of the fuse tube while the circuit is live.
  • Handle with Care: If the ceramic tube breaks, carefully clean up any fragments to avoid cuts.

3. Operating Instructions (Fuse Replacement)

  1. Power Disconnection: Ensure the equipment is completely powered off and disconnected from the power source.
  2. Locate Fuse Holder: Identify the fuse holder in your equipment. Open or unscrew its cover to access the fuse.
  3. Remove Blown Fuse: Carefully remove the blown fuse tube. Examine its markings to confirm its specifications (current, voltage, size).
  4. Insert New Fuse: Insert a new ceramic fuse tube with identical specifications into the fuse holder. Ensure it makes good electrical contact at both ends.
  5. Restore Power: Close the fuse holder cover securely and restore power to the equipment.
  6. Monitor: If the new fuse blows again, immediately disconnect power and inspect the circuit for underlying faults before attempting further repairs.
Fuse installation demonstration showing a fuse and a fuse holder

Figure 1: Fuse installation demonstration (RT18-32 shown as example)

4. Specifications

AttributeValue
Brand NameGIANTELE
Model NumberRO15
MaterialCERAMICS
Dimensions10mm (Diameter) x 38mm (Length)
Rated Voltage500V (AC/DC)
Current Ratings Available1A, 2A, 3A, 4A, 5A, 6A, 8A, 10A, 16A, 20A, 25A, 32A
Breaking Capacity50KA
Fuse TypeFast Blow
EU LVD Voltage ComplianceBelow 50Vac or 75Vdc
CertificationCE
OriginMainland China
Battery IncludedNo
Diagram showing the dimensions of a 10x38mm fuse

Figure 2: Fuse Dimensions (10mm diameter, 38mm length)

Close-up of a ceramic fuse with copper core round cap and nickel plating

Figure 3: Copper core round cap, nickel-plated for rust prevention

Image showing quartz sand as an arc extinguishing medium inside a fuse

Figure 4: Quartz sand arc extinguishing medium for high thermal conductivity and insulation

5. Maintenance

  • Regular Inspection: Periodically inspect fuses and fuse holders for any signs of damage, corrosion, or loose connections.
  • Proper Storage: Store spare fuses in a dry, cool environment, away from direct sunlight and corrosive substances.
  • Cleaning: If a ceramic fuse breaks, ensure all fragments are carefully removed from the fuse holder and surrounding area to prevent short circuits or further damage.

6. Troubleshooting

  • Fuse Blows Immediately After Replacement: This indicates an existing fault in the circuit, such as a short circuit or severe overload. Do not replace the fuse again until the underlying issue is identified and resolved.
  • Frequent Fuse Blowing: If fuses blow frequently, it suggests that the circuit is consistently drawing more current than the fuse's rating, or there is an intermittent fault. Verify the load requirements and ensure the fuse rating is appropriate. Consider consulting a qualified electrician.
  • Equipment Not Functioning After Fuse Replacement: Double-check that the new fuse is correctly seated in the holder and that its specifications match the original. Ensure all power connections are secure.

7. User Tips

  • When using these fuses for solar panel installations, especially with MPPT inverters, ensure the fuse's current rating is sufficient for the maximum output of your panels and the input capacity of your inverter. Some users have found success with higher amperage fuses (e.g., 30A) for prolonged high-power consumption scenarios, provided it aligns with equipment specifications.
  • The clear and legible printing on the fuse body helps in easily identifying the specifications, which is crucial for correct replacement.
  • These fuses are designed for both AC and DC applications up to 500V, making them versatile for various electrical systems, including those with photovoltaic inverters.

8. Frequently Asked Questions (FAQ)

Q: Are these ultra-fast fuses?
A: Yes, these are described as 'Fast Blow Ceramic Fuses', designed to react quickly to overcurrent conditions.
Q: Are these fuses suitable for solar panels (MC4 connections)?
A: Yes, the product description indicates suitability for 'photovoltaic inverters' and 'charging stations', which are common in solar setups. Ensure the amperage matches your specific solar system's requirements.
Q: Can these fuses be used for both DC and AC circuits?
A: Yes, these fuses are rated for 500V, which applies to both AC and DC applications. For EU Low Voltage Directive (LVD) compliance, they are suitable for voltages below 50Vac or 75Vdc.

9. Warranty and Support

For any questions regarding the installation, operation, or troubleshooting of your GIANTELE RO15 ceramic fuses, please contact your retailer or the manufacturer's customer support. Please refer to your purchase documentation for specific warranty terms and conditions.

© 2024 GIANTELE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.