INSE W1

Contents

INSE W1 Window Cleaning Robot

User Manual

Introduction

Thank you for choosing the INSE W1 Window Cleaning Robot with Automatic Water Spraying Function. This manual provides detailed instructions for the safe and effective operation of your new appliance. Please read it thoroughly before first use and keep it for future reference.

For additional information, you may refer to the User Manual (PDF).

Important Safeguards

When using any electrical appliance, basic safety precautions should always be observed to reduce the risk of death, injury, and electrical shock.

  • Carefully inspect the safety cable before each use. Ensure there is no damage and that it is securely buckled to a strong, immovable object.
  • When the product is working high above the ground, place warning marks on the ground below.
  • Do not spray water directly into this product. Do not use this product on glass with cracks.
  • When cleaning the external surface of this product, turn it off to avoid personal injuries from rotating parts.
  • Do not touch the rotating parts or openings of this product with your hand or any other part of your body.
  • Always follow the instructions in this manual. If you encounter issues, contact customer service directly. Do not attempt unauthorized repairs, as this may result in personal injury.
  • This product is intended for home environment use only.
  • Do not use a third-party charger. Do not remove the frame, battery, or charger without authorization.
  • If the product is damaged or cracked, discontinue use immediately and contact customer service.
  • Keep the charger away from heating sources.
  • If transporting the product, use the original packaging and ensure the product is turned off.
  • For long periods of non-use, fully charge the product, turn it off, and store it in a cool, dry place. Recharge the product at least every three months to prevent battery degradation.

Content of the Box

The package includes the following items:

  • Window Cleaning Robot x1
  • Mop Holder x2 (pre-installed)
  • Remote Control x1
  • Mops x6
  • Safety Cable x1
  • Adapter x1
  • AC Wire x1
  • Water Bottle x1
  • User Manual x1
  • Cotton Swab x2
Contents of the box including the W1 Window Cleaning Robot, remote control, and cleaning pads.
W1 Window Cleaning Robot, remote control, and accessories.

Setup Instructions

  1. Secure the Safety Cable: Ensure the knob of the safety cable is fully tightened to a sturdy frame or object. Fasten the buckle side of the safety cable to an object strong enough to prevent dragging, leaving sufficient length for the device to operate.
  2. Attach Mops: Cover each mop holder with a mop. If the glass surface has sand or heavy dust, it is recommended to clean it manually first to avoid scratching. If manual cleaning is not possible, turn off the water spray function and use dry mops to wipe off sand and dust before wet cleaning.
  3. Fill Water Tank: Open the water tank cover and fill it with purified water. This product cannot be drenched. Dry any residual moisture on the surface after filling. Using concentrated cleaning liquid is strictly prohibited to prevent blocking the spray nozzle and pump.
    Filling the water tank of the W1 Window Cleaning Robot.
    Fill the water tank with purified water.
  4. Verify Mop Holder Installation: Ensure the mop holder is installed correctly. After installation, observe from all sides (360°) to confirm each snap is securely in place to prevent air leakage.
  5. Connect Power: Insert the window cleaner's power cord into the end of the adapter and tighten. Connect the two ends of the AC wire to the adapter and a power socket, respectively.
  6. Power On and Place Robot: Long-press the power button (more than 3 seconds) to turn on the robot. Once the fan is running, attach the robot to the glass at a location far away from the window frame. If the robot cannot adhere to the glass, check for air leakage due to an improperly buckled holder.
  7. Test Spray Function (if needed): If the robot doesn't spray despite sufficient water in the tank, clean the nozzle surface with a cotton swab. To test further, restart the robot, hold it in your hand (top cover up & bottom down), and press the 'small water spray' key on the remote for the left nozzle, and the 'strong water spray' key for the right nozzle.
Video demonstrating the setup process, including filling the water tank, attaching pads, and placing the robot on the window.

Operating Instructions

Starting the Robot

  1. Ensure the power cord and plug are completely connected.
  2. Long press the Start/Power button (more than 3 seconds) to turn on the robot.
  3. After the fan is running, attach the robot to the glass at a location far away from the window frame.
  4. Ensure the robot is firmly stuck to the glass before letting go.
  5. Short press the power button to start the robot.

Path Planning and Cleaning Modes

The robot uses intelligent path planning for efficient cleaning.

  • Automatic Cleaning: Place the robot in the center of the glass. Long press the Power/Start button to turn it on, then short press to start. The robot will automatically move upwards, then right, reaching the top-right corner. It then cleans the glass in an S-shaped curve from top to bottom.
  • Water Spray Function: When the water spray function is on, the right nozzle sprays water when the robot moves right, and the left nozzle sprays water when it moves left.
  • Multiple Cleaning Modes: The robot offers various modes to suit your cleaning needs.
Diagram showing Fast Cleaning, Deep Cleaning, and Spot Cleaning modes.
Multiple cleaning modes: Fast Cleaning, Deep Cleaning, and Spot Cleaning.
Image illustrating the W1 Window Cleaning Robot's smart features including 3000Pa suction, two-way automatic water spray, remote control, and smart route navigation.
Smart and efficient cleaning features of the W1 robot.

Removing the Robot from Glass

  1. While the robot is running, hold the safety cable with one hand, short press the power button to stop the robot, and take it down with the other hand.
  2. If you cannot reach the robot and do not have the remote control, gently pull the safety rope to bring the robot to a reachable position. After powering off, remove the robot from the glass.
  3. After completely removing the robot, long-press the power button (more than 3 seconds) to turn it off.

LED Indicator Lamp and Voice Meanings

Working Status IndicationMeaning
Green LightWorking normally.
Green Light + 6 Long BeepsWindow cleaning is complete.
Red Light Flashing
  • Robot disconnected: Connect power or remove robot from glass.
  • Insufficient suction: Remove robot, check for air leakage.
  • Excessive/insufficient friction: Replace wipe cloth or spray water.
Red and Green AlternationInternal hardware error. Turn off, unplug, wait, then reconnect. If issue persists, contact customer service.
Green Light Flashing (when connected to power, but robot is off)Internal battery is charging.
Green Light (when connected to power, but robot is off)Internal battery is fully charged.

Remote Control

The remote control allows you to manage the robot's movement and functions.

Diagram of the remote control with buttons for navigation, start/pause, water spray, and cleaning modes.
Remote Control Layout and Functions.
  • Start (x1)/Pause/Continue: Press once to start, pause, or continue cleaning.
  • Navigation Arrows: Control the robot's direction (Up, Down, Left, Right).
  • Clean to the Top End: Directs the robot to clean towards the top edge.
  • Clean to the Bottom End: Directs the robot to clean towards the bottom edge.
  • Clean Left Area and Lower Area: Initiates cleaning in the specified left and lower regions.
  • Clean Right Area and Lower Area: Initiates cleaning in the specified right and lower regions.
  • Small Water Spray: Activates a light water spray.
  • Strong Water Spray: Activates a powerful water spray.
  • Water Spray On/Off: Toggles the water spray function.
  • Spot Cleaning: Initiates spot cleaning in a specific area.
  • Cleaning Twice (x2): Commands the robot to perform two cleaning cycles.

Maintenance

Water Tank Maintenance

  • Ensure water or cleaning solution does not spill out of the water tank. If accidental spills occur, dry immediately to prevent water damage to the robot.
  • When the robot is not in use, ensure there is no residual liquid in the water tank. If using a cleaning solution, pour it out, then fill the tank with a little fresh water to clean it, and empty it completely.
  • Important: Ensure there are no impurities in the added solution to avoid blocking the nozzle and pump.

General Cleaning

  • Regularly clean the mops. If residual round marks appear on the glass after cleaning, replace with a new mop.
  • Clean the nozzle surface with a cotton swab if the spray function is weak or blocked.

Troubleshooting

If you encounter any issues with your W1 Window Cleaning Robot, refer to the following guide:

  1. Red Indicator Flashing (continuous short sounds): Check the following:
    • Power cord plug is loose or damaged, causing power loss or poor contact.
    • Glass or mop is too wet, resulting in low friction.
    • Glass has impurities, causing too high friction.
    • Mop holder is incorrectly installed, leading to air leakage.
    • Sticky objects on glass causing too much friction.
    • Suction port is blocked.
  2. Red and Green Indicator Alternating (alarming sound): This indicates an internal hardware issue. Please contact customer service directly. For special glass, especially when cleaning the bottom, more time may be needed; use the remote control for manual guidance.
  3. Robot Cannot Move Freely: Change the mop or inspect the screws on the cleaning roller to ensure they are not loose.
  4. Mop Holder Shakes Excessively: Check if the wipe cloth is too wet and replace it with a dry cloth.
  5. Delayed Water Spray at Start: A slight delay in water spraying when the robot begins operation is normal.
  6. Residual Round Marks on Glass: After cleaning, if round marks remain, replace with a new mop.
  7. Robot Doesn't Stop Automatically: If the robot continues to move after completing cleaning, press the Pause Button on the remote or robot to stop it and take it down.
  8. Occasional Bug During Use: If a bug occurs, restart the robot.
  9. Downward Sliding: Check the following:
    • The cloth is too wet or too dirty.
    • The robot cannot resume work after a while; replace with a dry and clean wipe cloth.
    • The cloth is too dry, causing slips; turn on the water spray function to moisten the wipe cloth, then the robot can resume work.
  10. Air Leakage: Inspect the following:
    • Mop holder is installed correctly.
    • Wipe cloth installation for flatness.
    • Glass or other targeted surface is curved or covered with uneven surfaces (e.g., stickers).
    • Robot goes to the window frame, causing the mop holder to warp and produce air leakage.

Specifications

ParameterValue
ModelW1
Voltage100 - 240 V
Watt72W
Decibels≈65db
Size288*139*78mm
Current300mA
Capacity500mAh
UPS Battery Using TimeApprox 25 mins (remaining power of Built-In Battery will affect the time)
Suction Power2000-3000pa
Minimum Using Area300*300mm
Diagram showing the dimensions of the W1 Window Cleaning Robot: 28.8cm/11.3in length, 13.9cm/5.5in width, and 7.8cm/3.1in thickness.
Product Dimensions.

Safety Information

Usage Requirements

  • Ensure the safety rope is intact and fixed to an immovable object. For high-altitude outdoor work, set up ground safety warnings to prevent accidental falls.
  • Do not drench the robot with water. Do not use in rain, humid, or foggy conditions.
  • Do not use on cracked or broken glass. Confirm the window area is larger than 30x30cm. For windows with super narrow frames, beveled frames, no frames, or glass glue with uneven, raised, leaking seams, gaps, or other abnormal situations, use the remote control to guide the robot if necessary. (Using the robot in such abnormal environments is not recommended and requires caution, as it may cause a fall).
  • Always turn off the robot when cleaning its surface to avoid danger during movement.
  • Keep the robot and accessories out of reach of children. Do not allow children to operate this product. Do not touch the product with fingers or any body part while it is operating.
  • Use this product according to instructions. Contact customer service if you cannot troubleshoot. Do not attempt self-repair.
  • Operate only in home environments between 0°C and 40°C (32°F and 108°F). If the temperature is lower, use anti-freeze glass water.
  • Store the robot in a dry environment, away from direct light, and not with oil, gas, or flammable items.

Battery & Charging

  • Do not use third-party adapters, and do not disassemble or modify the robot, battery, or adapter.
  • If the charger is damaged or broken, discontinue use and contact customer service.
  • Place the adapter away from heat sources.
  • If the product is to be shipped, it is recommended to use its original packaging with the robot turned off.
  • If not used for a long time, fully charge the robot, turn it off, and store it in a cool, dry place. Charge it at least every 3 months to prevent over-discharge and extend battery life.

Warranty and Support

Warranty Information

PartsWarranty ContentPeriod of Warranty
RobotRobot unit1 Year
AccessoryMotor / Fan / Charging Adapter / Built-in Li Battery / Remote Control1 Year
ConsumablesWipes / Spray CanN/A

No warranty is provided for consumable accessories.

Non-Warranty Claims

The warranty does not cover issues arising from:

  • Unauthorized repair, misuse, collision, negligence, abuse, fluid ingress, accident, or alteration.
  • Incorrect use of non-standard accessories, or tearing/alteration of labels or anti-counterfeit labels.
  • Exceeding the warranty service period.
  • Non-compliance with performance failures.
  • Product failure or accessory damage due to human causes.
  • Damage caused by force majeure.
  • No valid purchase date record.

Fault List

PartFault Contents
RobotCannot start when powered on; Remote control cannot be controlled.
AdapterCannot properly power the robot.

Customer Information

Please keep your purchase receipt and warranty card for future reference. Record your product details below:

  • User Name: _________________________
  • Address: _________________________
  • Product Name/Model Number: W1 Window Cleaning Robot
  • Purchase Date: _________________________

User Tips

  • Mop Dampness: For optimal, streak-free cleaning, ensure your mops are adequately damp but not overly wet. If traces are left after wiping, the mop might be too dry.
  • Power Compatibility: The W1 Window Cleaning Robot supports a wide voltage range of 100-240V, making it suitable for use in various regions without needing a voltage converter.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.