Yinuogo YNG200

Contents

Yinuogo 9V-24V 433MHz Remote Control Receiver User Manual

Model: YNG200

1. Introduction

This manual provides detailed instructions for the installation, programming, and operation of your Yinuogo YNG200 9V-24V 433MHz Remote Control Receiver. This 2-channel receiver is designed to work with various fixed, learning, and rolling code remote controls, making it suitable for a wide range of applications including garage door openers, gate controllers, and other automation systems.

Yinuogo YNG200 2-Channel 433MHz Remote Control Receiver with compatible APRIMATIC remotes
Figure 1: Yinuogo YNG200 2-Channel 433MHz Remote Control Receiver with compatible APRIMATIC remotes.

2. Safety Information

  • Ensure the power supply is disconnected before any installation or wiring work to prevent electric shock.
  • This device operates on 9V-24V DC. Using an incorrect voltage may damage the receiver.
  • Installation should be performed by qualified personnel if you are unsure about electrical wiring.
  • Keep the device away from water and extreme temperatures.

3. Package Contents

  • 1 x Yinuogo YNG200 433MHz Remote Control Receiver
  • (Remote controls are typically sold separately or as part of a kit. Please check your specific purchase.)

4. Specifications

Feature Specification
Model Number YNG200
Power Supply AC/DC 9V-24V
Frequency 433MHz / 433.92MHz
Code Compatibility Fixed Code, Learning Code, Rolling Code
Channels 2 Channels (CH1 Relay Output, CH2 Relay Output)
Security Mode Fail Safe
Working Temperature -40℃ ± 80℃
Certification CE, FCC
Origin Mainland China
Receiver board showing compatibility with Fixed Code, Rolling Code, and Learning Code remotes
Figure 2: The receiver is compatible with Fixed Code, Rolling Code, and Learning Code remote controls.

5. Setup & Installation

5.1 Wiring Diagram

Connect the receiver to your motor or controller as shown in the diagram below. Ensure correct polarity for the power supply (V+ and GND).

Wiring diagram for connecting the receiver to a motor/controller and a gate system
Figure 3: General wiring diagram for the receiver in a gate or garage door system.

5.2 Power Supply

The receiver requires an AC/DC 9V-24V power supply. Connect the positive lead to the V+ terminal and the negative lead to the GND terminal.

5.3 Antenna

Connect the ANT (Antenna) wire to improve signal reception. For optimal performance, ensure the antenna is extended and not obstructed.

5.4 Relay Outputs

The receiver features two relay outputs, CH1 and CH2, which can be connected to control different devices or functions. Refer to your specific motor/controller manual for connection details.

Diagram illustrating how to replace an old receiver and add up to 100 new remote controls
Figure 4: The receiver can replace old units and support up to 100 new remote controls.

6. Programming

The receiver supports learning codes from various remote controls. Follow the steps below to program your remote(s).

6.1 Learning Transmitter Codes

  1. Press either the "learn 1" or "learn 2" button on the receiver for 1 second.
  2. The "learn_led" light on the receiver will illuminate.
  3. Within a few seconds, press the button on your remote control that you wish to program.
  4. Continue pressing the remote button until the "learn_led" on the receiver flashes and then goes out. This indicates that the transmitter's code has been successfully stored.
  5. Repeat these steps for any other remote controls you wish to program.

6.2 Clearing Transmitter Codes

To erase all stored remote control codes from the receiver:

  1. Press and hold either the "learn 1" or "learn 2" button on the receiver.
  2. Continue holding the button until the "learn_led" light illuminates and then goes out.
  3. All previously stored remote control codes will now be erased from the receiver's memory.

6.3 Programming Demonstration Video

Watch this video for a visual guide on how to program the receiver with a remote control.

Video 1: Demonstration of the learning process for the Yinuogo YNG200 receiver.

7. Operation

Once programmed, pressing the corresponding button on your remote control will activate the associated relay output (CH1 or CH2) on the receiver. This will trigger the connected device (e.g., open/close a garage door, turn on/off a light).

Close-up view of a two-button remote control (A and B) with a keyring attachment
Figure 5: Example of a compatible two-button remote control.
Remote control showing battery compartment for two CR2016 3V lithium batteries (not included)
Figure 6: Remote controls typically use two CR2016 3V lithium batteries (not included).

8. Applications

The YNG200 receiver is versatile and can be used in various automation scenarios:

  • Garage Door Openers
  • Gate Control Systems
  • Lighting Control (Lamps)
  • Industrial Equipment Control
  • Stage Lighting and Effects
  • Water Pump Control
  • Vehicle Modifications (e.g., remote trunk release)
Various applications for the remote control receiver including garage doors, car modifications, lamps, industrial equipment, stage lighting, and water pumps
Figure 7: Diverse applications for the YNG200 receiver.

9. Maintenance

  • Keep the receiver clean and free from dust and debris.
  • Avoid exposing the device to direct sunlight or excessive moisture.
  • Periodically check wiring connections to ensure they are secure.
  • If using remote controls, replace batteries (CR2016X2 for typical remotes) when performance degrades.

10. Troubleshooting

  • Receiver not responding to remote:
    • Check if the receiver is powered correctly (LED indicator should be on).
    • Ensure the remote control has fresh batteries.
    • Re-program the remote control to the receiver (refer to Section 6.1).
    • Verify that the remote control's frequency matches the receiver's (433.92MHz).
  • Limited range:
    • Ensure the antenna is properly connected and extended.
    • Check for obstructions between the remote and the receiver.
    • Avoid placing the receiver near large metal objects or other sources of interference.
  • Device not activating:
    • Check the wiring between the receiver's relay outputs (CH1/CH2) and the controlled device.
    • Ensure the controlled device is functioning correctly independently of the receiver.

11. User Tips

(No specific user reviews or Q&A were provided to generate user tips. General advice for remote control receivers includes ensuring clear line of sight for the antenna and testing range after installation.)

12. Warranty & Support

For warranty information or technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

A PDF version of the user manual may be available for download. Please check the product page or contact support for more information.

© 2024 Yinuogo. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.