PARKSON Motion Sensor LED Flood Light

Contents

PARKSON LED Flood Light with Motion Sensor User Manual

Model: Motion Sensor LED Flood Light

1. Product Overview

The PARKSON LED Flood Light with Motion Sensor is designed for outdoor illumination, providing bright and efficient lighting for gardens, walls, streets, and other outdoor areas. It features an integrated motion sensor for automated operation and is built with a durable, waterproof aluminum body.

Various wattages of LED flood lights with motion sensors illuminating a house at night.

Figure 1: PARKSON LED Flood Lights in various wattages (50W, 100W, 200W, 300W, 500W) with motion sensors.

Video 1: Product demonstration showing the LED flood light in operation, its waterproof capabilities, and motion sensor adjustment.

2. Setup and Installation

2.1 Safety Warnings

  • Installation must be performed by qualified electricians only.
  • Always switch off the main power supply before any installation or servicing.
  • Ensure all mounting items and screws are secure and fitted correctly.
  • Verify that the input voltage (220-240V AC, 50/60Hz) matches the lamp's requirements.
  • Floodlights should not be connected in series.
  • This floodlight is not dimmable.
  • Do not position the LED cover vertically upside down or vertically down during installation or use.

2.2 Unpacking

Carefully remove the flood light and all components from the packaging. Inspect for any damage. If any damage is found, do not proceed with installation and contact your supplier.

2.3 Mounting

The flood light comes with an adjustable mounting bracket. Securely attach the bracket to a stable surface (e.g., wall, pole) using appropriate screws and anchors (not included). The bracket allows for 180° rotation to direct the light as needed.

300W LED flood light mounted on a wall, showing its adjustable bracket and waterproof design.

Figure 2: The adjustable mounting bracket allows for flexible positioning of the flood light.

2.4 Wiring

Ensure the power supply is OFF before proceeding with wiring. Connect the wires from your power source to the flood light's wires according to the diagram below:

  • Brown Wire (L): Connect to Live (Phase)
  • Blue Wire (N): Connect to Neutral
  • Yellow & Green Wire (GND): Connect to Ground
Wiring diagram showing brown, yellow&green, and blue wires connected to Live, Ground, and Neutral respectively.

Figure 3: Wiring diagram for the LED Flood Light. Ensure correct connections for safe operation.

2.5 Motion Sensor Adjustment

The integrated motion sensor has three adjustable dials to customize its operation:

  • TIME: Adjusts the duration the light stays on after motion is detected and the sensing area is clear. Turn clockwise for longer duration, counter-clockwise for shorter.
  • SENS (Sensitivity): Adjusts the sensing distance of the motion sensor, typically from 2 to 10 meters. Turn clockwise for increased sensitivity/distance, counter-clockwise for decreased.
  • LUX (Light Sensor): Determines the ambient light level at which the sensor becomes active.
    • Set to the sun icon (max) for all-day sensing (24 hours a day).
    • Set to the moon icon (min) for night sensing only (sensor activates only after dark).
Close-up of the motion sensor with TIME, SENS, and LUX adjustment dials, and an illustration of sensing distance from 2 to 10 meters.

Figure 4: Motion sensor adjustment dials (TIME, SENS, LUX) and sensing range.

3. Operating Instructions

Once installed and configured, the flood light will operate automatically based on your motion sensor settings:

  • When motion is detected within the set sensitivity range and the ambient light conditions meet the LUX setting, the light will turn on.
  • The light will remain on for the duration set by the TIME dial.
  • If no further motion is detected within that time, the light will turn off.
  • If motion continues to be detected, the timer will reset, and the light will stay on.

4. Maintenance

  • Cleaning: Periodically clean the surface of the flood light and the sensor lens with a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • Inspection: Regularly check the mounting screws and wiring connections to ensure they remain secure.
  • Waterproof Rating: The flood light has an IP66 waterproof rating, making it suitable for outdoor use in various weather conditions. However, avoid submerging the unit in water.

5. Troubleshooting

ProblemPossible CauseSolution
Light does not turn onNo power; Sensor settings incorrect; Faulty wiringCheck power supply; Adjust LUX and SENS dials; Verify wiring connections.
Light stays on continuouslyTIME dial set too long; LUX dial set to all-day sensing; Constant motion in sensing areaAdjust TIME dial; Adjust LUX dial to night sensing; Check for objects causing constant motion.
Light flickersUnstable power supply; Loose wiring connectionEnsure stable power; Check and secure all wiring connections.
Light turns on/off rapidlySensor interference; Incorrect LUX setting for ambient lightRelocate sensor or remove obstructions; Adjust LUX setting.
Reduced brightnessPartial LED failure; Power supply issueContact support if individual LEDs are out; Check power supply voltage.

6. Specifications

FeatureSpecification
Input Voltage220-240V AC, 50/60Hz
Wattage Options50W, 100W, 200W, 300W, 500W
Luminous Flux249-2000 Lumens (varies by wattage)
Body MaterialAluminum
FinishPolished
Protection LevelIP66 Waterproof
Light SourceLED bulbs (included)
CertificationCCC, CE, ROHS
Sensing Distance2-10 meters
Bracket Rotation180°
Thickness23-24mm (approx. 0.94 inches)
OccasionOutdoor Wall

6.1 Dimensions by Wattage

Diagram showing dimensions for 50W, 100W, 200W, 300W, and 500W LED flood lights, including height, width, and overall thickness.

Figure 5: Dimensions for different wattage models.

  • 50W: 14.5cm (5.7in) H x 12cm (4.7in) W
  • 100W: 15.5cm (6.1in) H x 20cm (7.8in) W
  • 200W: 20.5cm (8in) H x 26.7cm (10.5in) W
  • 300W: 24cm (9.45in) H x 32.3cm (12.7in) W
  • 500W: 27.5cm (10.8in) H x 37.5cm (14.7in) W

7. User Tips

  • Power Consumption: Be aware that the actual power draw of LED flood lights can sometimes differ from the advertised wattage. For example, a 500W rated light might draw around 150W from the wall.
  • Proper Installation for Longevity: Ensure the light is installed correctly and securely. Improper installation or a crooked mount can hinder heat dissipation, potentially leading to premature LED failure or damage to the housing.
  • Troubleshooting Brightness Issues: If your light turns on but appears dim, check for consistent power supply. If individual LEDs are noticeably out, contact customer support.
  • Sensor Cycling: If the light turns on and off rapidly or unexpectedly, check for any objects that might be intermittently triggering the sensor, or adjust the LUX sensitivity to better match ambient light conditions.

8. Warranty and Support

For any warranty claims, technical support, or inquiries regarding your PARKSON LED Flood Light, please contact the seller or retailer from whom you purchased the product. Keep your proof of purchase for any warranty-related services.

© 2024 PARKSON. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.