Introduction
This manual provides comprehensive instructions for the safe operation, setup, and maintenance of your 4DRC 4D-F8 GPS Drone. Please read this manual thoroughly before operating the aircraft to ensure proper function and to avoid damage or injury. Keep this manual for future reference.
Disclaimer:
⚠️For recreation use only. Illegal modification of drones/planes is prohibited. Please also pay attention to the relevant laws and regulations on the use of drones/planes in your country/area to ensure legal use.
Important Safety Warning:
In order to meet the requirements of the aeronautical radio station's electromagnetic environment (various of aero models and UAV are not allowed to fly within the range of 10 km on each side of center line and 20km on both ends of the airport runway and in the) and civil aviation routes and airlines. Using various models and drones in the no-fly zone issued by the relevant state departments is prohibited.
Age Recommendation:
Suitable for ages over 14. Children should be guided by adults when operating the aircraft. This product is prohibited to be operated by children under 14 years old.
Package Contents
Verify that all items listed below are included in your package:
- Aircraft x 1
- Remote control x 1
- Micro USB cable x 1
- Type-C Charging Cable x 1
- Lithium battery x 1
- Fan blade x 4
- Screwdriver x 2 (one for assembly, one for general use)
- Operating Instructions x 1 (this manual)
- Storage bag (for some packages)
- Card reader (for some packages)
- Night light (for some packages)
Component Overview
Aircraft Parts
The aircraft consists of the following main parts:
- Fan blade
- Obstacle Avoidance Radar (present on F8 MAX model)
- Shell
- Camera (6K ESC lens)
- Optical camera (Bottom HD lens)
- Battery
- Aircraft power switch
- Motor
Remote Control Parts
The remote control features the following components:
- Antenna
- Left stick
- Right rocker
- Unlock (long press)
- Power switch (long press)
- Obstacle avoidance switch (long press)
- Headless mode (short press) / One key return (long press)
- Power Indicator
- GPS indicator light
- Obstacle avoidance indicator light
- Return indicator light
- Charging port
- Display screen
- Micro SD card slot
- GPS switch (long press)
- Fine tuning of camera angle
- Horizontal calibration (short press) / Geomagnetic calibration (long press)
- Speed gear
Setup Guide
1. Battery Charging
Ensure both the aircraft battery and remote control are fully charged before use.
Aircraft Lithium Battery Charging
- Push the battery rightwards into the aircraft body.
- To remove, gently press the battery until you hear a click, then pull it out.
- Insert the USB port of the USB charging cable into a computer USB port or a 5V⎯2A power adapter.
- Connect the other end of the USB charging cable to the battery socket.
- The red indicator on the battery module will be on during charging. It will turn off when fully charged.
Note: When the aircraft is not in use, do not leave the battery installed in the aircraft to prevent battery damage.
Remote Control Charging
- Plug the USB interface of the USB charging cable into a computer USB port or a 5V⎯2A power adapter.
- Plug the other end of the USB charging cable into the charging port of the remote controller.
- During charging, the indicator lights of the remote controller will light up in turn, and all the indicators will be always on after the remote controller is fully charged.
Warning: Only use the aircraft charging cable provided by the factory. Using other charging cables may cause serious damage to the battery and unexpected dangers.
2. MicroSD Card Installation
Insert the MicroSD card carefully into the slot on the remote control until it is firmly in position. To remove, gently press the card until you hear a click, then pull it out.
Note: The MicroSD card must be installed before starting the drone to enable photo and video capture during flight.
3. Aircraft Assembly
Radar Installation (for F8 MAX model)
- Use a flat-blade screwdriver to gently pry off the parts on the drone body where the radar will be installed.
- Align the two sides of the obstacle avoidance radar with the corresponding slots on the drone body and press firmly until they butt together.
Note: The radar components contain electronic parts. Do not use the drone in water or humid environments if the radar is installed.
Wind Blade Installation
Ensure correct installation of the fan blades. Each blade is marked with 'A' or 'B'. Unscrew the screw, remove the fan blade, and install the new blade according to the diagram. Incorrect installation will prevent the drone from taking off.
4. Unfolding the Aircraft
The aircraft is shipped in a folded state. Gently unfold the arms of the aircraft until they lock into place.
5. APP Download and Connection
Download the "4DRC PRO" app from your device's app store or by scanning the QR code provided in the original manual.
Connection Steps:
- Power on the aircraft, then power on the remote controller. Wait for frequency pairing (the fuselage lights will flash).
- After successful pairing, connect your mobile phone or iPad to the remote controller using a data cable.
- Alternatively, go to your mobile device's Wi-Fi settings, find the network named "4DRC*******", and connect to it.
- Once connected, open the "4DRC PRO" app to enter the control interface.
Note: For optimal performance, operate the drone away from other signal interference sources.
6. Pre-flight Calibration
Before flying, ensure the drone is calibrated correctly.
Horizontal Calibration
- Place the aircraft on a horizontal surface.
- Short press the horizontal calibration button on the remote control. The blue and red lights on the aircraft will flash quickly.
- When the blue and red lights remain constantly on, the calibration is complete, and the remote controller will emit a "beep".
Note: The aircraft must be on a horizontal surface during calibration.
Geomagnetic Calibration
- Long press the geomagnetic calibration key on the remote control until the front blue light and rear red light on the aircraft flash.
- Pick up the aircraft and rotate it clockwise horizontally until the front blue light and rear red light flash slowly. The remote controller will emit a "beep", indicating horizontal calibration is complete.
- Pick up the aircraft with its nose pointing vertically down, and rotate it clockwise until the blue light on the front and the red light on the rear of the aircraft are constantly on. The remote control will emit a "beep", indicating the guide calibration is complete.
Note: After geomagnetic calibration, perform horizontal calibration again.
7. Star Search Status (GPS Mode)
In GPS mode (default on power-on), the GPS indicator light on the remote control will flash slowly, indicating it's searching for satellites. The aircraft indicator light will be constantly on. Once the GPS indicator light on the remote control is constantly on and the red indicator light on the aircraft flashes, satellite search is successful, and the remote controller will "beep". The aircraft can then be unlocked for takeoff.
Note: You need to wait at least a few minutes for the first search. The drone can only take off when the app interface shows three or more satellite signal bars (the remote controller displays 10 or more satellite indices).
Operation Guide
1. Environmental Requirements for Flight
Choose an outdoor, open environment with no rain, snow, or strong wind. Maintain a safe distance from crowds, trees, wires, tall buildings, airports, and signal transmission towers. Avoid flying in small indoor environments with many obstacles.
2. Basic Flight Controls (Remote Control)
The remote control uses two joysticks for flight manipulation:
- Left Joystick (Throttle):
- Push up: Increases main blade rotation rate, aircraft rises.
- Push down: Decreases main blade rotation rate, aircraft descends.
- Push left: Aircraft nose turns left.
- Push right: Aircraft nose turns right.
- Right Joystick (Rudder/Pitch/Roll):
- Push up: Aircraft moves forward.
- Push down: Aircraft moves backward.
- Push left: Aircraft fuselage deviates left.
- Push right: Aircraft fuselage deviates right.
Warning: When the aircraft is within 1m of the ground, it may become unstable due to "ground effect response" from its own blade vortex. The lower the height, the greater this effect.
3. Start/Stop (GPS Mode)
To unlock the motors for takeoff:
- Push both the left and right joysticks on the remote controller outward simultaneously.
- Alternatively, long press the unlock key on the remote control.
Once unlocked, the aircraft can take off, and all indicator lights will be on. In the APP, you can also click the "One Key Unlock" icon.
4. Normal Mode Start/Stop (Indoor Operation)
For indoor flight, switch to Normal Mode (GPS indicator on remote control is off):
- Long press the GPS button on the remote control. The GPS indicator will turn off, entering Normal Mode.
- Push both the left and right joysticks outward to unlock the motors.
- Then, push up the left joystick to take off.
5. Obstacle Avoidance Mode (F8 MAX model only)
During flight, long press the obstacle avoidance switch key to activate this mode. If the aircraft approaches an obstacle (front/back/left/right/up), it will automatically hover and stop moving forward. Long press the key again to deactivate.
Note: The obstacle avoidance effect may be weak or lost under strong sunlight, with transparent/reflective objects (like glass), or with black objects.
6. One Key Return
Press the return button on the remote control, and the aircraft will return to the position above the takeoff point. If flying below a safe altitude, it will automatically ascend before returning. Manually control the directional lever to avoid obstacles and land.
Out-of-control return: If the remote controller's signal is lost for about 4 seconds, the aircraft will automatically return to the last known signal location.
Low-battery return: In case of low battery, the aircraft will be forced to return to a position about 10 meters above the takeoff place. Return cannot be cancelled during low-battery return.
7. Headless Mode
The drone's front at the time of code-matching is set as the front in headless mode. To adjust the direction, re-match the code, then short press the "headless mode" function key on the remote control. Short press again to exit.
Special Tip: Ensure the aircraft is aligned with a straight line and allow the gyroscope to automatically detect it for straight-line flight in headless mode.
8. Speed Switching
After takeoff, the drone defaults to low-speed mode (3-gear switching). Push the wheel on the remote controller to the right to increase speed (one "beep" for low, two "beeps" for high, three "beeps" for highest). Push the wheel to the left to decrease speed.
9. Lens Adjustment
Use the fine-tuning wheel on the remote controller to adjust the camera angle as needed. This can also be done via the "More Functions" icon in the APP control interface, then selecting "Lens Adjustment".
10. APP Control Interface Functions
The APP provides various intelligent flight modes and features:
- Multipoint Flight (Waypoint Flight): In GPS mode, select "More Functions" then "Waypoint Flight". Set a series of waypoints on the map. The drone will follow this preset trajectory.
- Orbital Flight: In GPS mode, select "More Features" then "Orbit Flight". The drone will automatically orbit a set radius. Adjust the radius and orbital speed using the right joystick.
- GPS Follow Mode: In GPS mode, select "More Functions" then "Follow". The drone will track your mobile device's location, maintaining a set distance. Lightly press the red icon to cancel.
- Gesture Recognition: When facing the drone's front camera (within 3m, good light), use specific hand gestures to trigger photo or video recording.
- "Yeah" Gesture: Make a "Yeah" gesture with one hand horizontally to take photos after a 3-second countdown.
- Palm Gesture: Put five fingers together and lift one hand horizontally to start video recording. Recording ends when the gesture is re-recognized (time difference > 3s).
- MV Interface: Click the "filter interface" icon in the APP to apply filters, record short videos, or take pictures, which are saved to the media library.
Maintenance
- General Care: Keep the drone clean and dry. Avoid exposing it to water or humid environments, especially components like the obstacle avoidance radar.
- Battery Care:
- Always charge the battery after 30 minutes of rest once it's depleted to prevent damage.
- Do not short-circuit, decompose, or throw the battery into fire.
- Avoid placing the battery in high-temperature environments (e.g., near electric heating devices).
- Do not mix different types of lithium batteries.
- When not in use, remove the battery from the aircraft to prevent damage.
- Propeller Maintenance: Regularly check propellers for damage. Replace any broken or deformed blades immediately using the provided screwdriver and spare propellers. Ensure correct 'A' and 'B' blade placement.
- Motor Care: The motors can become hot during operation. Avoid touching them immediately after flight to prevent burns.
- Storage: Store the drone and its components in a cool, dry place, ideally in the provided storage bag.
Troubleshooting
| Problem | Reason | Solution |
|---|---|---|
| Aircraft indicator flashes without any response | 1. Geomagnetic anomaly 2. Insufficient power |
1. Move aircraft to an open area and recalibrate geomagnetism (refer to Setup, Pre-flight Calibration). 2. Charge the battery. |
| Blades rotate but aircraft cannot fly | 1. Low battery 2.1 Blade deformation 2.2 Incorrect propeller installation |
1. Charge the battery. 2.1 Replace the blade. 2.2 If B1/B2 blade is broken, replace with B1/B2. If A1/A2 blade is broken, replace with A1/A2. Incorrect parts will prevent takeoff. |
| Aircraft vibrates badly | Blade deformation | Replace the blade. |
| Fine tuning done but aircraft still unstable | 1. Blade deformation 2. Defective motor |
1. Replace the blade. 2. Replace the motor. |
| Aircraft flies uncontrollably after impact | Three-axis acceleration sensor loses balance due to impact | Rest the aircraft for 5-10 seconds, then perform geomagnetic and horizontal calibration (refer to Setup, Pre-flight Calibration). |
Specifications
| Feature | Detail |
|---|---|
| Model | 4D-F8 |
| Brand Name | 4DRC |
| Category | Camera Drone |
| Drone Weight | 160g |
| Max Takeoff Weight | <1kg |
| Folded Dimensions | 22*18*7.5cm |
| Motor Type | Brushless Motor |
| Flight Time | 25min |
| Remote Distance | 3000M |
| Aircraft Operating Frequency | 2.4 GHz |
| Frequency | 5GHz |
| Transmission Range | others (long-distance image transmission) |
| Control Channels | 4 channels |
| Connectivity | APP Controller |
| GPS | Yes |
| Obstacle Avoidance Types | 360° automatic (F8 MAX), No support (F8 PRO) |
| Max Wind Speed Resistance | < 10 KM/H |
| Camera Integration | Camera Included |
| Camera Features | 4K HD Video Recording |
| Video Maximum Resolution | 6K (5780*2890) |
| Sensor Size | 1/6.0 inches |
| Camera Mount Type | Fixed Camera Mount, Other |
| Aerial Photography | Yes |
| Display Control | Yes |
| Removable/Replaceable Battery | Yes |
| Battery Weight | 90g |
| Battery Type | Li-ion |
| Nominal Voltage (Aircraft Battery) | 7.4V |
| Operating Voltage (Remote Control) | 3.7 V |
| Charging Ambient Temperature | 5℃ to 40℃ |
| Working Environment Temperature | 0℃ to 40℃ |
| Hover/Flight Noise | 80.5/82.3 (dB) |
| APP Supported Languages | Japanese, French, German, Italian, Spanish, Korean, Portuguese, English, Simplified Chinese, Traditional Chinese Style, Swedish, Polish, Russian |
User Tips
- Camera Quality: The drone features a 6K dual camera system for high-definition aerial photography. Ensure good lighting conditions for optimal results.
- Battery Management: Consider purchasing additional batteries for extended flight sessions, as the standard flight time is 25 minutes. Always allow batteries to rest for 30 minutes after discharge before recharging.
- SD Card for Recording: Remember to insert a MicroSD card into the remote control before flight if you plan to take photos or videos.
- GPS Signal Acquisition: Be patient during the initial GPS satellite search. The drone requires a few minutes and sufficient satellite signals (at least three bars on the app or 10+ indices on the remote) before it can take off in GPS mode.
- Novice Mode: If you are an experienced pilot, remember to disable novice mode in the app settings to unlock full flight distance and altitude capabilities.
- Hearing Protection: Avoid operating the drone near your ears, as the motor noise can cause hearing damage.
Warranty and Support
For detailed information regarding warranty, service, and additional support, please refer to the official user manual PDF available from the seller. This document contains comprehensive guides and diagrams that may not be fully replicated here.
Compliance Statement:
To meet the magnetic environment requirements of aeronautical radio stations. During the radio control order issued by the relevant state departments, the model remote control should be stopped within the city area as required.