JIANKEXING JK-X1-01

Contents

Designer Aluminum Floor Lamp and Table Desk Light User Manual

Model: JK-X1-01 | Brand: JIANKEXING

1. Introduction

Thank you for purchasing the JIANKEXING Designer Aluminum Floor Lamp or Table Desk Light. This manual provides essential information for the safe and efficient use of your new lighting fixture. Please read these instructions carefully before assembly and operation, and retain them for future reference.

2. Package Contents

Please check the package contents to ensure all parts are present and undamaged:

  • Lamp Base
  • Lamp Pole (for Floor Lamp) or Short Stand (for Table Lamp)
  • Multi-tiered Lampshade Assembly
  • Power Cord with Plug and Switch
  • Mounting Hardware (if applicable, for securing pole to base)
  • User Manual (this document)

Note: E27 LED bulb may be included depending on your purchase variant.

3. Safety Instructions

  • Ensure the power is off before assembly, installation, or maintenance.
  • Do not connect the lamp to power until fully assembled.
  • Use only E27 bulbs within the specified wattage range (6-10W).
  • Do not expose the lamp to water or excessive humidity.
  • Keep the lamp away from flammable materials.
  • If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

4. Setup and Assembly

Follow these steps to assemble your lamp:

  1. Carefully unpack all components and place them on a clean, flat surface.
  2. Attach the Pole/Stand to the Base: For floor lamps, screw the lamp pole securely into the lamp base. For table lamps, screw the short stand into the base. Ensure it is tightened firmly to prevent wobbling.
  3. Attach the Lampshade Assembly: Carefully place the multi-tiered lampshade assembly onto the top of the pole/stand. Ensure it sits correctly and is stable.
  4. Install the Bulb: Screw an E27 LED bulb (not exceeding 10W) into the lamp holder located within the lampshade assembly. Do not overtighten.
  5. Position the Lamp: Place the lamp on a stable, level surface (for table lamps) or floor (for floor lamps) away from edges or high-traffic areas where it could be knocked over.
  6. Connect to Power: Plug the power cord into a suitable electrical outlet.
Detailed view of lamp components, switches, and bulb fitting

Figure 4.1: Detailed view of lamp components, showing bulb fitting (E27), base, and switch types.

Table lamp dimensions diagram

Figure 4.2: Table lamp dimensions (Height: 56cm, Base Diameter: 18cm, Shade Diameter: 23cm).

5. Operating Instructions

Your lamp is equipped with an integrated switch for easy operation.

  • For Table Lamps: Use the inline push-button switch located on the power cord to turn the lamp ON or OFF.
  • For Floor Lamps: Use the foot-operated switch located on the power cord near the base to turn the lamp ON or OFF.

The illumination color temperature (Warm White 3000K, Neutral White 4000K, or Cold White 6000K) is determined by the E27 bulb you install.

6. Maintenance

  • Cleaning: Ensure the lamp is unplugged before cleaning. Wipe the lamp base, pole, and lampshade with a soft, dry cloth. Do not use abrasive cleaners, solvents, or polishes as they may damage the finish.
  • Bulb Replacement: Always unplug the lamp and allow the bulb to cool completely before attempting to replace it. Unscrew the old E27 bulb and screw in a new one, ensuring it is within the recommended wattage (max 10W LED).

7. Troubleshooting

ProblemPossible CauseSolution
Lamp does not turn on
  • Lamp not plugged in
  • Bulb is loose or faulty
  • Power outlet is not working
  • Switch is faulty
  • Ensure the power cord is securely plugged into a working outlet.
  • Check if the bulb is screwed in tightly. Replace the bulb if it is faulty.
  • Test the outlet with another appliance.
  • Contact customer support if the switch is suspected to be faulty.
Bulb flickers
  • Bulb is loose or incompatible
  • Faulty bulb
  • Ensure the bulb is screwed in tightly.
  • Replace the bulb with a new, compatible E27 LED bulb.

8. Specifications

Model NumberJK-X1-01
Brand NameJIANKEXING
MaterialAluminum, Iron, Stainless Steel
Light SourceE27 LED Bulbs (Bulb may be included)
Wattage6-10W (LED)
VoltageAC 90-260V
Lighting Area3-5 square meters
Luminous Flux249-2000 Lumens
Dimensions (Floor Lamp)Diameter 35cm x Height 155cm
Dimensions (Table Lamp)Diameter 35cm x Height 65cm
ControlInline Push Button Switch (Table Lamp), Foot Switch (Floor Lamp)
CertificationCE
Installation MethodAssembly

9. User Tips

  • Bulb Choice: Experiment with different E27 LED bulbs to achieve your desired ambiance. A 3000K (Warm White) bulb creates a cozy atmosphere, while a 6000K (Cold White) bulb provides brighter, more task-oriented lighting.
  • Placement: Position your lamp to maximize its unique multi-tiered shade design, which casts interesting light patterns. Avoid placing it where direct glare might be an issue.

10. Warranty and Support

This product comes with a 2-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase.

For any questions, technical support, or warranty claims, please contact your seller directly. Refer to the product listing or your purchase confirmation for seller contact information.

A PDF version of the user manual may be available for download from the seller's product page: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.