1. Introduction
Thank you for choosing the Shimano RT CL900 Ice Technology Disc Brake Rotor. This manual provides essential information for the safe and correct installation, operation, and maintenance of your disc brake rotors. The RT CL900 is engineered for superior heat dissipation and reliable braking performance, suitable for both road and mountain bike applications.
The RT CL900 features a sandwich composite construction with an aluminum layer between two stainless steel layers, enhanced with Ice-Technologies FREEZA and a special heat-dissipating coating to prevent overheating during demanding descents. Its design is optimized for low noise and weight.
Video: Overview of Shimano RT CL900 Disc Brake Rotors.
2. Important Safety Information
DANGER: Failure to follow instructions will result in death or serious injury.
WARNING: Failure to follow instructions could result in death or serious injury.
CAUTION: Failure to follow instructions could cause personal injury or physical damage to equipment and surroundings.
General Safety Precautions
- This manual is intended for professional bicycle mechanics. Users not professionally trained should consult a bicycle dealer for assistance.
- Always read all instruction manuals included with the product.
- Do not disassemble or modify the product beyond what is stated in this manual.
- Wear approved eye protection when performing maintenance.
- Downhill and freeriding are dangerous. Riders must wear protective gear and perform thorough safety checks.
- Familiarize yourself with the brake's performance in a controlled environment. High braking performance may be unsuitable for city streets without extreme care.
- Learn proper braking technique for your bicycle model. Improper use can lead to loss of control or falls.
- Keep fingers away from the rotating disc brake rotor; it is sharp and can cause severe injury.
- Do not touch calipers or disc brake rotors immediately after riding; they become hot and can cause burns.
- Prevent oil or grease from contacting the disc brake rotor and brake pads, as this will impair braking performance.
- Check brake pad thickness; do not use if less than 0.5 mm.
- Do not use cracked, deformed, or excessively thin (less than 1.5 mm) disc brake rotors.
- Avoid continuous brake application, which can cause sudden increases in lever stroke and loss of braking.
- Do not use brakes with fluid leaks.
- Avoid applying the front brake too strongly to prevent wheel lock-up and falls.
- Reduce speed and apply brakes early and gently in wet weather or on wet road surfaces.
Mineral Oil Handling Precautions
- Eye Contact: Flush with fresh water immediately and seek medical assistance.
- Skin Contact: Wash well with soap and water.
- Inhalation: Use in a well-ventilated area. If mist/vapors are inhaled, move to fresh air, cover with a blanket, stay warm, and seek medical advice.
- Ingestion: Do not drink. May cause vomiting or diarrhea.
- Keep out of reach of children.
- Do not cut, heat, weld, or pressurize the mineral oil container.
- Dispose of used oil according to local codes.
- Store mineral oil in a sealed container, in a cool, dark area, away from direct sunlight, heat, or flame.
3. Package Contents
Your Shimano RT CL900 Disc Brake Rotor package typically includes:
- Shimano RT CL900 Disc Brake Rotor (140mm or 160mm, as selected)
- Internal Lock Ring (for Center Lock hubs)

Image: Shimano RT CL900 Disc Brake Rotors (140mm and 160mm shown).
4. Specifications
| Feature | Description |
|---|---|
| Brand Name | SHIMANO |
| Model Number | CL900 (RT-CL900) |
| Type | Disc Brake Rotor |
| Braking System | Hydraulic Disc Brake (Hydraulic Brake Pad) |
| Components | Disc Brake |
| Size (Diameter) | 140mm, 160mm |
| Material Disc | Sandwich composite (Stainless Steel outer, Aluminum core) |
| Material Spider | Aluminum |
| Technology | Ice-Technologies FREEZA, Heat-distributing coating |
| Weight (Approx.) | 96g (140mm), 114g (160mm) |
| Origin | Japan (Jp) |
| Compatibility | For brake pads with narrow pad shape. Lock ring with internal toothing: compatible with 9/10mm quick release and 12mm through axle. For 15mm and 20mm through axle, use SM-HB20 lock ring. |


Image: Shimano RT CL900 140mm (left) and 160mm (right) Disc Rotors with internal lock rings.
5. Setup and Installation
This section outlines the tools required and the steps for installing your Shimano RT CL900 Disc Brake Rotor. Refer to your brake caliper's manual for specific caliper installation details.
5.1. List of Tools to be Used
| Tool | Description |
|---|---|
| 2 mm Hexagon Wrench | For various small adjustments. |
| 3 mm Hexagon Wrench | For bleed screw, caliper fixing bolts. |
| 4 mm Hexagon Wrench | For brake hose connection. |
| 5 mm Hexagon Wrench | For mount adapter bolts. |
| 8 mm Spanner | For brake hose connection bolts. |
| Utility Knife | For cutting brake hose. |
| Slotted Screwdriver | General purpose. |
| TL-BH61 | Brake hose tool. |
| TL-FC36 | Disc brake rotor lock ring tool. |
| Micrometer | For measuring rotor/pad thickness. |
| Hexalobular [#15] | For disc brake rotor fixing bolts (if using SM-RTAD05 adapter). |
5.2. Disc Brake Mount Adapter Installation (for 180/203 mm rotors)
If you are using 180mm or 203mm disc brake rotors, you may need a mount adapter (e.g., SM-MA-F180P/P2, SM-MA90-F180P/P for 180mm; SM-MA-F203P/PM, SM-MA90-F203P/PM for 203mm).
- Place the adapter onto the brake caliper, then install the adapter to the frame. Use a 5 mm hexagon wrench for the bolts.
- Tighten the bolts to 6-8 N-m.
- Secure the caliper fixing bolt.
5.3. Disc Brake Rotor Adapter Installation (SM-RTAD05)
The SM-RTAD05 adapter allows installation of 6-bolt type disc brake rotors onto Center Lock system hubs/wheels. This product may introduce more play than normal in the disc brake rotor, potentially interfering with brake pads or calipers.
- Place the disc brake rotor adapter onto the hub.
- Place the disc brake rotor onto the hub, then temporarily fix it in place by tightening the disc brake rotor fixing bolts (Hexalobular [#15]).
- Wear gloves and turn the disc brake rotor clockwise with some force. Then, tighten the disc brake rotor fixing bolts in the order shown in the illustration (1-6) to 2-4 N-m.
- Fit the washer.
- Tighten the disc brake rotor lock ring using the TL-FC36 tool to 40 N-m.
5.4. Brake Rotor Installation (Center Lock)
- Ensure your hub is a Center Lock type.
- Align the splines of the disc brake rotor with the splines on the hub.
- Slide the rotor onto the hub until it seats fully.
- Place the lock ring over the rotor and thread it onto the hub.
- Using the TL-FC36 tool, tighten the lock ring to 40 N-m.
5.5. Brake Hose Installation
Refer to your brake caliper and lever manual for specific hose routing. Ensure the brake hose is not twisted during installation.
- Cutting the Brake Hose: Use a utility knife to cut the brake hose. Ensure the cut end is perpendicular to the hose length to prevent fluid leaks.
- Marking the Hose: Mark the brake hose to ensure it's securely fitted into the brake caliper and lever mounts. For SM-BH90-SB, SM-BH90-SS, SM-BH59-JK-SS, the length inside the mount is approx. 11mm. For SM-BH80, it's 14mm.
- Attaching to Brake Lever: Pass the brake hose through the connecting bolt and olive. Use a tapered tool to smooth the cut end of the hose, then mount the connector insert. Attach the hose to the TL-BH61 tool, secure it in a vise, and use a hammer to firmly knock the connector insert until it touches the end of the hose. Push the brake hose while tightening the connecting bolt with an 8mm spanner to 5-7 N-m.
- Attaching to Brake Caliper: Follow the same procedure as for the brake lever. Push the brake hose while tightening the connecting bolt with an 8mm spanner to 5-7 N-m (for straight type) or 4mm/3mm hexagon wrench to 8-10 N-m / 4-6 N-m (for banjo type).
6. Operating Your Disc Brakes
Proper operation of your disc brakes is crucial for safety and performance. The RT CL900 rotors are designed to work with hydraulic disc brake systems.
- Brake Lever Feel: Ensure your brake levers feel firm and consistent. Any sponginess may indicate air in the system, requiring bleeding.
- Braking Technique: Apply both front and rear brakes smoothly and progressively. Avoid sudden, hard braking, especially with the front brake, to prevent skidding or loss of control.
- Brake Burn-in Period: New disc brakes and rotors have a burn-in period. Braking force will gradually increase as the pads and rotors bed in. Be aware of this change in performance.
- Wet Conditions: In wet weather, braking distance will be longer. Reduce your speed and apply brakes earlier and more gently.
- Rotor Temperature: Disc brake rotors can become very hot during use. Avoid touching them immediately after riding.
7. Maintenance
Regular maintenance ensures optimal performance and longevity of your Shimano RT CL900 Disc Brake Rotors and braking system.
7.1. Adding SHIMANO Genuine Mineral Oil and Bleeding Air
Bleeding the brake system removes air bubbles and ensures proper hydraulic function. A funnel is needed for this process.
- Set the brake lever horizontally.
- Remove the upper bleed screw and attach the oil funnel.
- Remove the bleed nipple cap of the caliper, fill the syringe with oil, and connect the tube to the bleed nipple.
- Loosen the bleed screw by 1/8th of a turn. Push the syringe plunger to add oil until no air bubbles come out through the funnel.
- Temporarily close the bleed nipple. Remove the syringe, covering the end with a rag.
- Secure a tube and bag to the bleed nipple, loosen the bleed screw. Oil and air bubbles will flow naturally.
- Keep the oil funnel filled to maintain the liquid level.
- Once no more air bubbles come from the bleed nipple, temporarily close the bleed screw.
- Depress the brake lever, open and close the bleed screw rapidly (approx. 0.5 seconds) 2-3 times to release air from calipers. Tighten bleed screw to 4-6 N-m.
- Check lever operation: it should feel stiff. If not, repeat from step 5.
- Set the lever unit horizontally, tilt 30 degrees in one direction, check for air, then tilt 30 degrees in the other direction and check again.
- Plug the oil funnel with the oil stopper (O-ring facing downward).
- Remove the oil funnel while plugged, then tighten the bleed screw to 0.5-1 N-m. Wipe away any overflowed oil.
- After installing pads and spacer, depress the brake lever several times to check normal operation and for fluid leaks.
7.2. Replacing the Brake Pads
Replace brake pads when they are worn down to 0.5 mm thickness or if oil adheres to them.
- Remove the wheel from the frame and remove the brake pads.
- Clean the pistons and surrounding area.
- Use a flat-shaped tool to push the pistons straight back into the caliper. Do not use sharp tools.
- Install the new brake pads and pad spacers (red). Bend open the split pin.
- Depress the brake lever several times until it feels stiff.
- Remove the pad spacers.
- Install the wheel and check for interference between the disc brake rotor and brake pads.
- After checking the oil level, close the reservoir tank cover.
- Return the brake lever to its original position.
7.3. Cleaning
Use soapy water and a dry cloth to clean the brake system. Do not use commercial brake cleaners or silencing agents. For carbon levers, use a soft cloth with neutral detergent.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Weak or inconsistent braking | Oil/grease on rotor/pads, worn pads, air in hydraulic system, cracked/deformed rotor. | Clean rotor/pads with isopropyl alcohol, replace worn pads, bleed brakes, replace damaged rotor. |
| Brake lever feels spongy | Air in hydraulic system, low fluid level. | Bleed brakes, check fluid level and top up if necessary. |
| Brakes squeal or make noise | Contaminated pads/rotor, misaligned caliper, worn pads, new pads/rotor not bedded in. | Clean pads/rotor, align caliper, replace worn pads, perform brake burn-in procedure. |
| Rotor rubbing on pads | Misaligned caliper, bent rotor, pistons not fully retracted. | Align caliper, true bent rotor or replace, push pistons back into caliper. |
| Fluid leak | Loose connections, damaged hose/seal. | Check all connections for tightness, replace damaged components. |
9. User Tips
- Installation Tip: When installing new rotors, consider using new brake pads or lightly sanding existing pads to ensure a flat surface. This helps prevent uneven wear and sticking.
- Performance: Users report excellent fade-free braking and that these rotors are often very straight out of the box, requiring minimal adjustment.
- Noise Reduction: Many users find these rotors contribute to reduced braking noise compared to other models.
- MTB Compatibility: These rotors perform well on mountain bikes, offering reliable braking and compatibility with various MTB brake systems.
10. Warranty and Support
For warranty claims or technical support, please contact your authorized Shimano dealer or the place of purchase. Keep your proof of purchase for warranty service. Shimano products are designed for durability and performance, but proper installation and maintenance are key to their longevity.
For the latest technical documents and manuals, please visit the official Shimano website.