SZRZGT 2.4G Dimming power supply

Contents

SZRZGT 2.4G Remote Control LED Driver Power Supply User Manual

Model: 2.4G Dimming power supply

1. Product Overview

This manual provides instructions for the installation, operation, and maintenance of your SZRZGT 2.4G Remote Control LED Driver Power Supply. This device is designed to power and control dual-color LED strips, allowing for dimming and color temperature adjustments via a 2.4G wireless remote.

LED Driver and Remote Control

Figure 1: LED Driver Power Supply with its 2.4G Remote Control.

2. Safety Precautions

Read all safety instructions before installation and use. Failure to follow these instructions may result in electric shock, fire, or other hazards.

  • The input voltage must be strictly within the nominal operating voltage range (AC110V-240V). Exceeding this range can cause damage.
  • Do not use in high-temperature, sealed environments without adequate heat dissipation.
  • Ensure proper creepage distance and electrical clearance for the light source board according to UL8750/IEC 60598-1 safety standards.
  • Do not connect the output terminals of two or more LED drivers in parallel.
  • Some models may require auxiliary heat dissipation plates. Refer to product specifications.
  • For non-isolated drive power supplies, consider configuring a leakage protector at the input.
  • Ensure insulation withstand voltage of supporting lamp board is at least 3kV (4kV or above recommended).
  • Avoid short circuits between positive/negative poles of the output and ground.
  • Do not conduct voltage withstand tests directly between "input-output" terminals of non-isolated power supplies.
  • Installation must comply with IEC/EN 60598-1, IEC/EN 61347, GB 4706.1, and GB 7000.1 safety specifications.
  • Ensure reliable grounding. Grounding resistance should be less than 0.1 Ω. Do not use lamp posts or housings as grounding media.
  • Install the power supply horizontally and securely with screws. Do not install vertically or suspend by wires.
  • For Class I LED drivers, ensure effective grounding via a dedicated grounding device.
  • Do not directly expose the power supply to the heat sink of the lighting fixture. Design a protective chamber or use waterproof facilities.
  • For outdoor use, install a lightning arrester (≥10kV) at the AC input terminal.
  • Install away from combustible materials.
  • Do not modify or damage the power supply structure. Do not stack multiple power supplies without gaps.

3. Setup and Installation

3.1 Wiring Instructions

Follow the power label identification carefully. Do not connect input and output in reverse. Confirm all wiring is correct and reliable before powering on.

  • Keep input lines, output lines, dimming lines, programming lines, and auxiliary power lines separate to prevent contact with each other or other live objects.
  • Lay AC input, output, auxiliary, and dimming lines separately to avoid long-distance proximity and parallelism, preventing signal crosstalk.
Wiring Diagram for LED Driver

Figure 2: Wiring Diagram. Connect AC input to the driver, and the driver output to the LED luminaire. Ensure PE (Ground) connections where applicable.

3.2 Remote Control Pairing

The remote control needs to be paired with the LED driver the first time it is used. Follow these steps:

  1. Connect the LED driver to your lamp (LED strip/chandelier).
  2. Turn on the lamp and wait for 3-5 seconds.
  3. Within 3-5 seconds of turning on the lamp, press the "ON 1#" button on the remote control for 3-5 seconds, or press it 3-5 times rapidly.
  4. The lamp will flicker on/off three times, indicating successful pairing.
  5. You can now use the remote to control the lamp.
Remote Control Pairing Instructions

Figure 3: Visual guide for remote pairing. For Remote B (similar to the included remote), turn on the lamp for 3-5 seconds, then press ON 1# for 3-5 seconds. The lamp will turn on/off 3 times to confirm pairing.

4. Operating Instructions

Once paired, use the 2.4G remote control to manage your LED lighting.

Close-up of 2.4G RF Remote Control

Figure 4: 2.4G RF Remote Control layout.

Remote Control Functions:

  • ON/OFF: Power the LED lights on or off.
  • Bright+/Dim-: Adjust the brightness level of the LEDs.
  • Warm/Cool: Adjust the color temperature between warm white and cool white.
  • CH1/CH2/CH3/CH4 (On/Off): If your lighting system supports multiple channels, these buttons can control individual channels.
  • K (Mode/Scene): May cycle through preset modes or scenes (functionality depends on the connected LED luminaire).

5. Maintenance

  • Keep the LED driver and remote control in a dry environment.
  • Clean the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Ensure proper ventilation around the LED driver to prevent overheating.

6. Troubleshooting

ProblemPossible CauseSolution
Remote control does not work / Cannot connect with remote.
  • Remote not paired.
  • Remote battery low/dead (if applicable, remote not include battery).
  • Obstruction between remote and driver.
  • Perform remote pairing procedure (Section 3.2).
  • Ensure line of sight between remote and driver.
LED lights do not turn on.
  • No power to the driver.
  • Incorrect wiring.
  • Faulty LED strip/luminaire.
  • Driver malfunction.
  • Check power supply to the driver.
  • Verify all wiring connections (Section 3.1).
  • Test LED strip/luminaire with another compatible power source if possible.
LED lights flicker or dim unexpectedly.
  • Unstable input voltage.
  • Overloaded driver (LED wattage exceeds driver capacity).
  • Loose connections.
  • Ensure stable AC input voltage.
  • Verify total LED wattage does not exceed 54-72W.
  • Check and secure all wiring connections.

7. Specifications

FeatureSpecification
Model Number2.4G Dimming power supply
Brand NameSZRZGT
Input VoltageAC110V-240V
Output VoltageDC24V
Output Current2.6A (Max)
Power Output54W / 72W (depending on input voltage)
Control Method2.4G RF Wireless Remote Control
Power SourceDC
Dimensions (L x W x H)160mm x 45mm x 28mm
LED Driver with detailed specifications

Figure 5: LED Driver unit displaying model, input, output, and size specifications.

8. User Tips

  • First-Time Pairing: Always ensure you perform the remote control pairing procedure correctly on the first use. This is a common point of confusion if the remote doesn't seem to work.
  • Input Voltage Impact: Note that if you use a 110V input, the actual power output will be approximately 50% of the maximum 72W, so plan your LED load accordingly.
  • Remote Battery: The remote control does not include batteries. Ensure you have the correct type of battery (usually AAA or CR2032, check remote compartment) ready for use.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the seller's terms of sale or contact the point of purchase. Keep your purchase receipt as proof of purchase.

For additional documentation, you may refer to the official user manual PDF: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.