Professional 1600W Heat Gun Set

Contents

Professional 1600W Heat Gun Set

Model: JD1600/JD3400

Introduction

Thank you for choosing the Professional 1600W Heat Gun Set. This hot air tool is designed for a variety of professional welding and heating applications. This manual provides essential information for the safe and effective use, setup, operation, and maintenance of your heat gun. Please read these instructions carefully before use and keep them for future reference.

Professional 1600W Heat Gun Set with various accessories including nozzles, rollers, and brushes.

Figure 1: Professional 1600W Heat Gun Set with accessories.

The included operating manual (PDF) for the LEMOTE energy 1600/3400 Hot Air Tool provides detailed instructions and diagrams. You can refer to the original PDF for further details.

Safety Warnings

DANGER! Always observe the following safety precautions to prevent injury or damage:

  • Electrical Safety: Unplug the tool from the mains before opening or performing any maintenance. Ensure the power supply cord, connector, and extension cable are free from electrical and mechanical damage before use. The voltage rating on the tool must correspond to the mains voltage.
  • Fire and Explosion Hazard: Incorrect use, such as overheating materials, can create a fire or explosion risk, especially near combustible materials or explosive gases.
  • Burn Hazard: Do not touch the hot heating element housing or air nozzle. Allow the tool to cool down completely after use. Do not direct the hot air flow towards people or animals.
  • Supervision: This tool must be operated under supervision. Heat can ignite flammable materials that are not visible. Only qualified specialists or individuals under their supervision should use this machine. Children are not authorized to use this machine.
  • Environmental Protection: Protect the tool from dampness and wet conditions.
  • Maintenance and Repairs: Repairs should only be carried out by authorized service points. Use only original Weldy accessories and spare parts.

Kit Contents

Your Professional 1600W Heat Gun Set typically includes the following items:

  • 1x Hot air welding gun (220V, 1600W)
  • 1x Replacement Heating element (220V, 1550W)
  • 1x 45mm Silicone seam roller
  • 1x Seam tester probe with plastic handle
  • 1x 40mm Flat weld nozzle
  • 1x 20mm Flat weld nozzle
  • 1x Brushes
  • 1x Plastic carrying case
Heat gun with a flat weld nozzle attached.

Figure 2: Heat gun with a flat weld nozzle attached.

Technical Specifications

The following table outlines the key technical specifications for the 1600W Heat Gun:

Attribute Specification
Voltage 110/220 V
Power 1600 W
Frequency Range 50Hz - 60Hz
Temperature Range 68°F-1300°F / 20°C- 700°C
Air Volume Approx. 250 l/min
Static Pressure Approx. 3000 Pa
Noise Emission Level 67 dB
Protection Class II (double insulation)
Size Ø 90mm x 360mm, handle 55mm
Weight 1.3 kg (with power cord)

Note: Technical data and specifications are subject to change without prior notice.

Heat gun with dimensions indicating a length of 32cm (12.6 inches).

Figure 3: Heat gun dimensions.

Setup

Initial Start-up

  1. Ensure the heat gun is clean and free from obstructions.
  2. Select the appropriate nozzle for your application and securely attach it to the heat gun.
  3. Connect the heat gun to a suitable power outlet (110/220V, 50/60Hz).
  4. Turn on the power switch.
Examples of heat gun applications, including welding tarpaulins, flooring, and pond liners.

Figure 4: Various applications of the heat gun.

Changing Heating Element

Refer to the original operating manual for detailed diagrams and instructions on how to safely change the heating element. This procedure should only be performed when the tool is unplugged and completely cool.

Nozzle Attachment

The heat gun is designed for easy attachment and removal of various nozzles. Ensure the nozzle is firmly secured before operation to prevent accidental detachment during use.

Operation

Temperature Adjustment

The heat gun features adjustable hot air from 68°F-1300°F (20℃ to 700℃). Use the temperature control knob to set the desired temperature for your specific application. Start with a lower temperature and gradually increase it as needed.

Welding Techniques

For welding applications, ensure the surfaces are clean and dry. Apply consistent pressure with the seam roller as you move the heat gun along the seam to create a strong, seamless weld. Practice on scrap materials before working on your final project.

Shutting Down

To turn off the heat gun, switch off the power. Do NOT adjust the temperature knob to "0" immediately after working. Instead, directly turn off the main switch and allow the gun to cool down for approximately 5 minutes. This delay helps to cool down the hot air gun components and prolong its lifespan.

Maintenance

Cleaning the Air Filter

Regularly clean the air filter to ensure optimal performance and prevent overheating. Refer to the original operating manual for detailed diagrams and instructions on how to access and clean the air filter. Ensure the tool is unplugged and cool before performing any cleaning.

General Care

  • Keep the tool clean and free from dust and debris.
  • Store the tool in its plastic carrying case in a dry place when not in use.
  • Regularly inspect the power cord and plug for any signs of damage.

Applications

This hot air tool is suitable for a wide range of professional applications, including:

  • Welding of all thermoplastic synthetic materials.
  • Welding of foils and plastic sheeting.
  • Shrinkage and forming of thermoplastic synthetic materials.
  • Activation and detaching of solvent-free adhesives and hot melt adhesives.
  • Drying of watery-moist surfaces.
  • Soldering of copper pipes, solder connectors, and metal foils.
  • Repairing tarpaulins and tents.
  • Sealing advertising banners.
  • Welding PVC vinyl decking flooring coverings and linoleum.
  • Welding PVC / TPO / EPDM single-ply roofing membranes.
  • Welding of technical textiles.
  • Welding pond foil liners.
  • Welding swimming pools.

Troubleshooting

If you encounter issues with your heat gun, consider the following common troubleshooting steps:

  • No Power: Check if the power cord is securely plugged into a working outlet. Inspect the cord and plug for any damage. Ensure the power switch is in the 'ON' position.
  • Insufficient Heat: Verify that the temperature setting is appropriate for your task. Ensure the air filter is clean and not obstructed, as a clogged filter can reduce airflow and heating efficiency.
  • Reduced Airflow: Check the air intake and nozzle for any blockages. Clean the air filter if it appears dirty.
  • Overheating: If the tool feels excessively hot or shuts off unexpectedly, ensure proper ventilation around the tool. Clean the air filter. Allow the tool to cool down completely before resuming use.

If problems persist after attempting these steps, please contact an authorized service center for assistance.

User Tips

  • Proper Shut-down: To extend the life of your heat gun, do NOT adjust the temperature knob to "0" immediately after use. Instead, turn off the main power switch and allow the gun to run for approximately 5 minutes to cool down its internal components before completely unplugging it.
  • Material Compatibility: Always test the heat gun on a small, inconspicuous area of your material first to ensure compatibility and to find the optimal temperature setting.
  • Cleanliness: Keep your work area and the tool's air vents clean to prevent dust and debris from being drawn into the motor, which can affect performance and lifespan.

Warranty Information

The guarantee and warranty rights for this tool are provided by the relevant distributor/seller. Any manufacturing or workmanship defects will be repaired or replaced at the discretion of the distributor. To validate warranty claims, an invoice or delivery document is required.

Important Notes:

  • Heating elements are typically excluded from warranty coverage.
  • Warranty does not apply to defects caused by normal wear and tear, overload, or improper handling.
  • Warranty claims will be rejected for tools that have been altered or changed by the purchaser.

Support and Further Information

For more detailed instructions, diagrams, and safety information, please refer to the official user manual PDF:

View User Manual (PDF)

If you require further assistance or have questions not covered in this manual, please contact your seller or an authorized service center.

© 2024 Professional. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.