Honda CB190R / CBF190R

Contents

Motorcycle Windshield Installation and User Manual

For HONDA CB190R / CBF190R (2016-2023)

Honda CB190R/CBF190R Windshield

Image: Front view of the windshield with model compatibility text.

1. Product Overview

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your new motorcycle windshield designed for Honda CB190R and CBF190R models from 2016 to 2023. This windshield is designed to enhance your riding comfort by deflecting wind and protecting against road debris.

2. Setup and Installation

2.1 Tools Required

  • Phillips screwdriver set
  • Socket wrench set (10mm socket with long extension recommended)
  • Allen wrench set
  • Torque wrench (recommended)
  • Soft cleaning cloth

2.2 Step-by-Step Installation

  1. Pre-Installation Preparation
    • Turn off the motorcycle ignition and place it on a flat, stable surface.
    • Ensure the engine and fairing are completely cool to avoid burns.
    • Clean the mounting area on the front fairing to remove dirt or debris.
  2. Remove the Original Windscreen
    • Locate the factory fasteners (screws/bolts) securing the stock windscreen to the front fairing.
    • Use the matching screwdriver or socket to loosen and remove all fasteners.
    • Carefully lift the original windscreen straight off the mounting posts. Keep any rubber grommets, washers, or spacers for reuse.
  3. Prepare the New Windscreen
    • Inspect the new windscreen for scratches, cracks, or defects before installation.
    • Fit the saved rubber grommets or included hardware into the mounting holes of the new windscreen.
  4. Align the New Windscreen
    • Hold the new windscreen up to the fairing, aligning all mounting holes with the posts.
    • Ensure the windscreen sits flush against the fairing with no gaps or misalignment.
  5. Secure the Fasteners
    • Insert the screws/bolts through the windscreen and into the fairing posts.
    • Hand-tighten each fastener in a crisscross pattern (start with the center, then outer corners) to distribute pressure evenly.
    • Torque the fasteners to the manufacturer's recommended specification (typically 3-5 N·m) to avoid cracking the windscreen.
  6. Final Inspection & Safety Check
    • Gently wiggle the windscreen to confirm it is secure with no play.
    • Check for any interference with the handlebars, controls, or turn signals when turning the handlebar.
    • Perform a short test ride at low speed to verify stability and no wind-induced vibration.
Windshield installed on motorcycle front view

Image: Front view of the windshield installed on a Honda CB190R/CBF190R motorcycle.

Close-up of windshield mounting bracket

Image: Close-up view of the mounting area and bracket on the motorcycle.

2.3 Important Safety Warnings

  • Do not over-tighten the fasteners, as this can crack or deform the windscreen.
  • If you experience excessive vibration or noise after installation, stop use immediately and recheck the alignment and tightness.
  • Improper installation may cause the windscreen to detach during riding, leading to a safety hazard. Consult a professional mechanic if you are unsure.

3. Operating Instructions

Once properly installed, your windshield operates passively by deflecting wind and debris away from the rider. No active controls or adjustments are required during operation. Ensure the windshield is clean and free from obstructions for optimal visibility.

4. Maintenance

To maintain the clarity and integrity of your windshield:

  • Clean the windshield regularly with a soft cleaning cloth and mild soap and water.
  • Avoid using abrasive cleaners, solvents, or harsh chemicals, as these can damage the PC material.
  • Rinse thoroughly with clean water and dry with a soft, lint-free cloth to prevent water spots.
  • Periodically check all mounting fasteners to ensure they remain tight.

5. Troubleshooting

  • Windshield feels loose or vibrates:
    • Gently wiggle the windscreen to confirm it is secure with no play.
    • Re-check all mounting fasteners and tighten them to the recommended torque specification (3-5 N·m).
    • If excessive vibration or noise persists, stop use immediately and consult a professional mechanic.
  • Interference with handlebars or controls:
    • Turn the handlebars fully from lock to lock and check for any contact with the windshield, controls, or turn signals.
    • If interference occurs, re-check the alignment during installation. Minor adjustments to the brackets may be possible if the metal is deformable.

6. Specifications

FeatureSpecification
Model CompatibilityHonda CB190R, CBF190R (2016-2023)
Shield MaterialPC (Polycarbonate)
Bracket MaterialSteel Iron
Shield Thickness2.5mm
Bracket Thickness2mm
Production ProcessLaser cutting / CNC bending
Item Weight0.4 kg
Item Height10 cm
Item Width25 cm
Item Length25 cm

7. User Tips

  • Installation Access: The windshield is typically installed on the bolts that hold the motorcycle display. A 10mm socket with a long extension is often necessary to reach these bolts without difficulty.
  • Bracket Adjustment: The metal brackets are firm but can be carefully deformed or adjusted during installation if minor alignment corrections are needed.

8. Warranty and Support

For any issues, questions, or support regarding your windshield, please contact the seller directly. Ensure you provide your purchase details for faster assistance.

Manufacturer Information:

Supplier Name: Guangzhou Rebel Moser Trading Co., Ltd
Address: Room401-BO, No.129, Dongping North Road, Yongping Street, Baiyun District, Guangzhou City, Guangdong Province, China
Email: 17316801864@139.com

EU Representative Information:

Company Name: Synertrade FR SAS
Address: 9 rue du Bat d'Argent, 69001 Lyon, France
Email: info@syner-sarl.cn

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.