4DRC F8 MAX

Contents

4DRC F8 MAX GPS Drone User Manual

Model: F8 MAX | Brand: 4DRC

Suitable for ages over 14

1. Introduction

This manual provides detailed instructions for the safe operation and maintenance of your 4DRC F8 MAX GPS Drone. Please read this manual thoroughly before operating the aircraft to ensure proper use and to prevent damage or injury.

The 4DRC F8 MAX is an advanced GPS drone featuring high-definition cameras (available in 6K or 8K UHD), 360° intelligent obstacle avoidance, and a smart remote control with a built-in screen for real-time FPV (First Person View). It is equipped with a powerful brushless DC motor for stable flight and offers various intelligent flight modes.

4DRC F8 MAX GPS Drone and Remote Control

Image: The 4DRC F8 MAX GPS Drone and its remote control, highlighting 8K high definition, GPS positioning, and brushless machine.

Video: Overview of the 4DRC F8 MAX GPS Drone's features, including brushless motor, hand launch, GPS, HD lens, speed adjustment, long-range flight, screen display, HD picture, obstacle avoidance, trajectory planning, and intelligent homecoming.

2. Safety Warnings

Failure to follow these instructions may result in injury, damage to the product, or other unforeseen dangers.

  1. The packaging and instructions contain important information and should be kept.
  2. With this aircraft, you are responsible for ensuring that no harm will be caused to the personal and property of others.
  3. Commissioning and installing of aircraft must be strictly in accordance with the operating instructions, and attention shall be paid to the distance between the aircraft and the user or other people shall be 2 to 3m to prevent the aircraft from bumping into the head, face and body of people and causing injury in flying and landing, etc.
  4. Our company and distributors are not responsible for any loss and damage, as well as injury to people caused by improper use or operation.
  5. Children should be guided by adults when operating the aircraft. This product is prohibited to be operated by children under 14 years old.
  6. Please follow the instructions or packaging instructions to install and use correctly, and some parts should be assembled by adults.
  7. The product contains small parts, please place it out of the reach of children to prevent the risk of accidental eating or suffocation.
  8. It is strictly forbidden to play on the road or in the place where water is accumulated to avoid accidents.
  9. Please put away the packing materials in time to avoid harm to children.
  10. Do not disassemble or modify the aircraft. Disassembly or modification may cause malfunction to the aircraft.
  11. The charging cable needs to be inserted into the designated power supply 5V=2A that is the same as the product label.
  12. The use of other charging cables will cause damage to the battery and may cause unexpected dangers.
  13. The charging cable is not a toy.
  14. When charging the rechargeable battery, it must be under the supervision of an adult. When charging, it must be far away from flammable materials. During charging, the guardian should not leave the monitoring range.
  15. Please do not short circuit or squeeze the battery to avoid explosion.
  16. Do not mix different types of lithium batteries.
  17. The aircraft uses a rechargeable lithium battery, which needs to be pulled out for charging.
  18. Do not short-circuit, decompose or throw the battery into fire; do not put the battery in a place with high temperature and heat (such as in fire or near electric heating device).
  19. The aircraft should be used as far away from other electrical equipment and magnetic objects as possible, they may cause mutual interference.
  20. Please keep a safe distance from the high-speed rotating propeller to avoid the risk of scalp or cut.
  21. The motor is a hot part; please do not touch it to avoid burns.
  22. LED has laser radiation; please do not give direct light beam to others.
  23. Do not use the model near your ears! Misuse may cause hearing damage.
  24. The USB charging cable must use the data cable provided by our company to charge the battery, otherwise it will cause serious damage to the battery and will lead to unexpected danger.
  25. To meet the magnetic environment requirements of aeronautical radio stations. During the radio control order issued by the relevant state departments, the model remote control should be stopped within the city area as required.
  26. Turn off the switch and unplug the battery when the battery of the aircraft is used up, and charge after 30 minutes of rest, otherwise the battery will be easily damaged.

Aeronautical Radio Station Warning: In order to meet the requirements of the aeronautical radio station's electromagnetic environment, various aero models and UAVs are not allowed to fly within the range of 10 km on each side of the center line and 20km on both ends of the airport runway and in civil aviation routes and airlines. Using various models and drones in the no-fly zone issued by the relevant state departments is prohibited.

3. Package Contents

Please check the package contents carefully upon unboxing:

  • Aircraft x1
  • Remote control x1
  • Micro USB cable x1
  • Type-C Charging Cable x1
  • Lithium battery x1 (Quantity may vary based on set specification)
  • Fan blade x4
  • Screwdriver x1
  • Operating Instructions x1
  • Obstacle avoidance head (if included in your package)
  • Storage bag (if included in your package)
  • Card reader (if included in your package)
  • Night light (if included in your package)
Package contents for 8K Camera version

Image: Typical package contents for the 8K Camera + 360° Obstacle Avoidance version.

Package contents for 6K Camera version

Image: Typical package contents for the 6K Camera + 360° Obstacle Avoidance version.

4. Product Overview

4.1 Name of each part of aircraft

  1. Fan blade
  2. Obstacle Avoidance Radar
  3. Shell
  4. Camera
  5. Optical camera
  6. Battery
  7. Aircraft power switch
  8. Motor
Close-up of drone dual camera system

Image: Close-up view of the drone's dual camera system, showing the 6K ESC lens and Bottom HD lens.

4.2 Name of each part of the remote control

  1. Antenna
  2. Left stick
  3. Right rocker
  4. Unlock (long press)
  5. Power switch (long press)
  6. Obstacle avoidance switch (long press)
  7. Headless mode (short press) / one key return (long press)
  8. Power Indicator
  9. GPS indicator light
  10. Obstacle avoidance indicator light
  11. Return indicator light
  12. Charging port
  13. Display screen
  14. Micro SD card slot
  15. GPS switch (long press)
  16. Fine tuning of camera angle
  17. Horizontal calibration (short press) / Geomagnetic calibration (long press)
  18. Speed gear
Person flying drone with remote control

Image: A person operating the drone with the high-definition large-screen remote control.

5. Setup

5.1 Unfolding the Aircraft

The aircraft is in a folded state when shipped. Follow these steps to unfold it:

  1. Gently pull out the arms until they are fully extended.
  2. Ensure all arms are locked into position.
Folded drone held in hand

Image: The drone in its folded, compact state, held in hand.

5.2 Radar Installation

  1. Use a flat-blade screwdriver to gently pry the designated parts on the drone body where the radar will be installed.
  2. Align the obstacle avoidance radar head with the drone body. The arrows indicate that the two sides of the pressed radar part are butted on the body. Press firmly until it clicks into place.

Note: There are electronic components in the location where the radar components are installed on the aircraft, so it must not be used in water or in a humid environment.

Obstacle avoidance head in box

Image: The obstacle avoidance head in its packaging.

Drone with obstacle avoidance head attached

Image: The drone with the obstacle avoidance head correctly attached.

5.3 Wind Blade Installation

To install or replace wind blades:

  1. Unscrew the screw holding the fan blade.
  2. Remove the old fan blade.
  3. Install the new fan blade, ensuring it matches the 'A' or 'B' marking on the blade with the corresponding arm.
  4. Tighten the screw.

Note: The fan blade is printed with letters of A and B. Please install it correctly according to the diagram, otherwise it cannot take off.

5.4 MicroSD Card Installation

The drone supports microSD cards for storing photos and videos.

  • Insert: Insert the card carefully into the slot until it is firmly in position.
  • Remove: Press the memory card gently until you hear a click sound, indicating it has snapped out. Then, carefully pull it out.

Note: A micro SD card must be installed to take photos and video capture during flight. Insert the memory card before starting the machine, otherwise the card will not be read.

5.5 Battery Charging

5.5.1 Aircraft Lithium Battery Charging

The aircraft uses a rechargeable lithium battery. It needs to be removed from the aircraft for charging.

  1. Push the battery rightwards to remove it from the aircraft.
  2. Connect the USB charging cable to the battery socket.
  3. Plug the USB end of the charging cable into a computer USB port or a 5V=2A power adapter.
  4. The red indicator on the module battery will be on during charging and will turn off when fully charged.

Note: When the aircraft is not used, do not install the battery in the aircraft to avoid battery damage. Charge after 30 minutes of rest if the battery is fully discharged.

5.5.2 Remote Controller Charging

The remote controller is charged via a USB Type-C cable.

  1. Plug the USB interface of the USB charging cable into a computer USB port or a 5V=2A power adapter.
  2. Plug the Type-C end of the charging cable into the charging port of the remote controller.
  3. During charging, all indicator lights on the remote controller will light up in turn. All indicators will be continuously on when fully charged.

Warning: It must be charged with the aircraft charging cable provided by the factory. Other charging cables cannot be used. Be sure to remember to avoid accidents.

6. APP Download and Installation

The 4DRC F8 MAX drone can be controlled via a dedicated mobile application.

6.1 Download and Install the Software

  • Android: Scan the provided QR code and choose to open and download in your browser.
  • iOS: Scan the provided QR code to install from the App Store.
  1. Power on the aircraft, then power on the remote controller, and wait for frequency pairing.
  2. After successful frequency pairing, connect your mobile phone to the image transmission interface of the remote controller using a data cable.
  3. On your mobile device (phone or iPad), go to "Settings", turn on Wi-Fi, find the device named "4DRC*******" in the wireless network list, and connect to it.
  4. After successful connection, exit the settings.
  5. Open the "4DRC PRO" software icon on your mobile phone to enter the control interface.

Note: Try to stay away from other signal source environments when flying. Requires the "4DRC PRO" app to perform this step.

7. Pre-Flight Preparation (Using Remote Control)

7.1 Environmental Requirements Before Flight

  • Choose an outdoor and open environment with no rain, snow, or strong wind.
  • Stay away from crowds, trees, wires, tall buildings, airports, and signal transmission towers.
  • Do not fly in small indoor environments with many obstacles.

7.2 Aircraft Power On and Frequency Matching

  1. Turn on the power of the aircraft and place it on a horizontal surface. The aircraft will automatically enter frequency matching state, and the fuselage lights will flash.
  2. Long press the power switch button on the remote control. The indicator light on the remote control will flash.
  3. Push the left joystick to the top first, then to the bottom.
  4. For successful frequency matching, the aircraft lights will stop flashing and remain on constantly. The remote control will emit a "beep".

Note: Set the aircraft in a correct direction, with the nose facing forward. It must be placed on a horizontal plane. The aircraft/remote controller must ensure sufficient power or it cannot take off!

7.3 Calibration Procedures

7.3.1 Horizontal Calibration

  1. Short press the horizontal calibration button on the remote control. The blue and red lights on the aircraft will flash quickly.
  2. When the blue and red lights on the aircraft are always on, the calibration is complete. The remote controller will emit a "beep".

Note: In calibration, the aircraft must be placed on a horizontal surface to complete the calibration.

7.3.2 Geomagnetic Calibration

  1. Long press the geomagnetic calibration key on the remote control until the front blue light and the rear red light flash on the aircraft.
  2. Pick up the aircraft and rotate it clockwise horizontally until the front blue light and rear red light flash slowly. The remote controller will emit a "beep", indicating horizontal calibration is completed.
  3. Pick up the aircraft with its nose vertically down, and rotate it clockwise until the blue light on the front and the red light on the rear of the aircraft are always on. The remote control will emit a "beep", indicating the guide calibration is completed.

Note: Once geomagnetic calibration is completed, please carry out the level calibration again.

7.4 GPS Star Search Status (In GPS mode by default)

When the remote controller is in GPS mode, the GPS indicator light flashes slowly, indicating that the GPS is in satellite search status, and the aircraft indicator light is always on. When the GPS indicator light of the remote controller is always on and the red indicator light of the aircraft flashes, it means that the satellite search is successful, and the remote controller gives a "beep" prompt. At this time, the aircraft can be unlocked to take off.

Note: You need to wait at least a few minutes for the first search. The drone can only take off when the app interface shows three or more satellite signal bars (the remote controller displays 10 or more satellite indices).

7.5 Start/Stop (GPS Mode)

To unlock the aircraft for takeoff:

  • Push the left and right joysticks on the remote controller outward simultaneously.
  • Alternatively, keep a long press on the unlock key.

Note: Without successful satellite search, the aircraft can be unlocked, but it cannot take off. All indicator lights will be on after takeoff.

APP operation: Click the "One Key Unlock" icon in the APP control interface to achieve one-key unlock.

8. Operating Instructions

8.1 Remote Control Method (Joystick Controls)

The remote control uses two joysticks for flight control:

  • Left Joystick (Throttle):
    • Push up: Increases main blade rotation rate, aircraft rises.
    • Push down: Decreases main blade rotation rate, aircraft descends.
    • Push left: Aircraft nose turns left.
    • Push right: Aircraft nose turns right.
  • Right Joystick (Rudder):
    • Push up: Aircraft moves forward.
    • Push down: Aircraft moves backward.
    • Push left: Aircraft fuselage deviates to the left.
    • Push right: Aircraft fuselage deviates to the right.

Warning: When the aircraft is within 1m from the ground, it may become unstable due to "ground effect response" from its own blade vortex. The lower the height, the greater this effect.

8.2 Obstacle Avoidance Mode

This mode helps the drone avoid obstacles (not available in GPS mode).

  • Activate: During flight, long press the obstacle avoidance switch key.
  • When active, if the aircraft approaches a wall or other obstacles (front/back/left/right/up), it will automatically hover and stop moving forward.
  • Deactivate: Long press the obstacle avoidance switch key again.

Note: Under sunlight or strong light, transparent/reflective objects (e.g., glass), and black objects, the obstacle avoidance effect may be weak or lost.

8.3 One Key Return

Press the return button on the remote control, and the aircraft will return to the position above the takeoff point. If the aircraft is below a safe altitude, it will automatically ascend before returning. If obstacles are encountered during descent, manually control the directional lever to avoid them and pull down the throttle to land.

APP operation: Click the "one-key return" icon in the APP control interface. During return flight, click this icon again to cancel the return.

Warning: Out-of-control return: If the remote controller's signal is interrupted for about 4s, the aircraft will automatically fly back to the area with signal. Low-battery return: In case of low battery, the aircraft will be forced to return to about 10 meters above the takeoff place. During low battery return, the return cannot be cancelled.

8.4 Headless Mode

When code-matching is turned on, the front of the aircraft is set as the default front in headless mode. To adjust the direction, re-match the code and short press the remote controller's "headless mode" function key. To exit, gently press this function key again.

Special Tip: Ensure the aircraft is aligned with a straight line and allow the gyroscope to automatically detect the straight line for accurate headless mode flight.

8.5 Speed Switching

After takeoff, the drone defaults to low-speed mode (3-gear switching).

  • Increase Speed: Push the wheel remote controller to the right.
    • One "beep": Low-speed gear.
    • Two "beep beep": High-speed gear.
    • Three "beep beep beep": Highest-speed gear.
  • Decrease Speed: Push the wheel remote controller to the left to lower the speed gear in sequence.

APP operation: Click the "More Functions" icon in the APP control interface to switch flight speed.

8.6 Lens Adjustment

Adjust the camera angle using the fine-tuning wheel on the remote controller.

APP operation: Click the "More Functions" icon in the APP control interface to enter lens adjustment and adjust the lens angle as needed.

8.7 Normal Mode Start/Stop (Indoor Operation)

For indoor operation, switch to normal mode (GPS indicator on remote control is off).

  1. Long press the GPS button on the remote control. The GPS indicator will turn off, entering normal mode.
  2. Push the left and right joysticks on the remote controller outward to unlock, or long press the unlock key.
  3. Then push up the left joystick to take off.

8.8 Multipoint Flight Mode (GPS Mode)

  1. In GPS mode, click "More Functions" icon in the APP control interface to enter waypoint flight. The interface will switch from image transmission to map page.
  2. On the map page, click to set the track range for single or continuous waypoints. If waypoints are too dense, use the delete icon to remove them.
  3. After setting waypoints, click the send icon. The aircraft will fly to all waypoints from the initial point. The direction can be controlled by the joystick during flight.

8.9 Orbital Flight Mode (GPS Mode)

  1. In GPS mode, click "More Features" icon in the APP control interface to enter orbit flight mode. The aircraft will automatically orbit in a radius.
  2. The radius can be adjusted on the APP.
  3. Push the right direction joystick (left/right) to adjust orbital speed.
  4. Push the right direction joystick (front/rear) to adjust orbit radius.
  5. Press the orbit button again to end orbit flight.

8.10 GPS Follow Mode (GPS Mode)

In GPS mode, click the "More Functions" icon in the APP control interface to enter follow mode. The aircraft will use the distance from its current position to your mobile device (phone or iPad) as a reference, tracking changes in your device's location. Lightly press the red icon to cancel following.

8.11 Gesture Recognition

When facing the camera's front lens, click the gesture photo button on the APP and use the following gestures to trigger photo or camera functions:

  • Yeah gesture photo: In front of the aircraft lens (approx. 3m), make a "Yeah" gesture with one hand horizontally. After recognition, a 3-second countdown will begin before taking photos.
  • Palm gesture video-recording: In front of the aircraft lens (approx. 3m), put five fingers together and lift one hand horizontally. After recognition, recording will start. Recording ends when the gesture is re-recognized (if the time difference is greater than 3s).

Special prompt: Aim directly at the lens and perform gesture recognition about 2-3M away from the lens in an environment with good light and background.

8.12 MV Interface

Click the "filter interface" icon in the APP control interface. After entering, choose your favorite filter effect, then click the recording icon to start recording. After recording, the synthesized short video or picture will be saved to the media library.

Special prompt: During recording, you can rotate the screen or switch the filter effect, and also use the joystick on/off to control the direction and altitude of the aircraft.

9. Maintenance

  • Always turn off the aircraft and remote control after use.
  • Unplug the battery from the aircraft when not in use for extended periods to prevent damage.
  • Store the drone and its components in a dry, cool place, away from direct sunlight and extreme temperatures.
  • Regularly check propellers for damage and replace them if necessary.
  • Keep the camera lenses clean using a soft, dry cloth.
  • Avoid exposing the drone to water or humid environments, especially the radar components.
  • Do not disassemble or modify the aircraft or remote control, as this may cause malfunction and void any potential warranty.

10. Troubleshooting

Question Reason Solution
The aircraft indicator flashes without any response.
  • Geomagnetic anomaly
  • The aircraft has insufficient power
  • Move the aircraft to an open area and recalibrate the geomagnetism (refer to section 7.3.2).
  • Charge the battery (refer to section 5.5.1).
The blades of the aircraft rotate but cannot fly.
  • Low battery
  • Blade deformation
  • Installation error of AB propeller
  • Charge the battery (refer to section 5.5.1).
  • Replace the deformed blade.
  • Ensure correct installation of A1/A2 and B1/B2 blades (refer to section 5.3).
The aircraft vibrates badly. Blade deformation Replace the blade.
Fine tuning is done but still can't make the aircraft stable.
  • Blade deformation
  • Defective motor
  • Replace the blade.
  • Replace the motor.
After the impact, start the aircraft again and it flies uncontrollably. The three-axis acceleration sensor loses its balance due to impact. It will be OK after 5-10s of resting the aircraft, or by geomagnetic calibration and level calibration (refer to sections 7.3.1 and 7.3.2).

11. Specifications

11.1 Aircraft

  • Model: 4D-F8 MAX
  • Drone Weight: 160g
  • Takeoff Weight: 242g
  • Dimensions: 22*18*7.5cm
  • Material: Plastic, Metal
  • Motor: Brushless Motor
  • Video Capture Resolution: 4K UHD, 8K UHD, 6K UHD (depending on model)
  • Aerial Photography: Yes
  • Camera Mount Type: Fixed Camera Mount
  • Features: App-Controlled, FPV Capable, GPS, Integrated Camera, Obstacle Avoidance, Wi-Fi, Other
  • Indoor/Outdoor Use: Indoor-Outdoor
  • Anti-wind Ability: <10km/h
  • Flight Time: 10~20 minutes
  • Remote Distance: 3000M
  • Operating Frequency: 2.4GHz
  • Temperature of working environment: 0°C to 40°C
  • Hover/Flight Noise: 80.5/82.3 (dB)

11.2 Remote Control

  • Controller Battery: 3 x 1.5 AAA Battery (not included)
  • Control Channels: 4 channels
  • Controller Mode: MODE1, MODE2
  • Remote Control: Yes
  • Operating Voltage: 3.7 V
  • Operating Frequency: 2.4GHz

11.3 Aircraft Battery

  • Battery Type: Lithium Battery
  • Nominal voltage: 7.4V
  • Charging Voltage: 3.7V
  • Charging Time: About 200 minutes
  • Charging ambient temperature: 5°C to 40°C
  • Power Source: Electric
  • Is Batteries Included: Yes
  • Plugs Type: USB

12. User Tips

  • Battery Management: Always ensure both the drone and remote control batteries are fully charged before flight. Consider purchasing spare batteries for extended flight sessions. Remember to let the drone battery rest for 30 minutes after full discharge before recharging.
  • Environmental Awareness: Pay close attention to wind conditions. The drone has an anti-wind ability of less than 10km/h. Avoid flying in strong winds to prevent loss of control.
  • Flight Range: Be mindful of the remote distance (up to 3000M) and camera image transmission range. Always keep the drone within visual line of sight and within the effective control range.
  • Obstacle Avoidance: While the drone features 360° obstacle avoidance, be aware of its limitations, especially with transparent, reflective, or very dark objects, and in strong sunlight. Always maintain situational awareness.
  • Read the Manual: The included English manual is comprehensive. Refer to it for detailed instructions on setup, calibration, and advanced flight modes.

13. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Please note that improper use, unauthorized modifications, or failure to follow the instructions in this manual may void your warranty.

© 2023 4DRC. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.