Voktta a99

Contents

99 Gears Spot Welder DIY Kits User Manual

Model: a99 | Brand: Voktta

1. Introduction

The Voktta 99 Gears Spot Welder DIY Kit is an intelligent digital display spot welder designed for various battery types, including 18650 lithium batteries. It features 99 adjustable power levels, real-time voltage monitoring, and MOS tube temperature protection to ensure efficient and safe spot welding. This manual provides essential information for setting up, operating, and maintaining your spot welder.

Intelligent Digital Display Spot Welder features
Image highlighting the intelligent features of the spot welder, including 5 MOS in parallel for 300A instantaneous current resistance, 99 gears, digital tube display, over-voltage/low-voltage protection, and MOS over-temperature protection.

2. Safety Information

  • Caution: The red soldering pens are electrically charged. Do not touch any components on the board while the device is powered on.
  • Ensure proper ventilation when operating the spot welder.
  • Always wear appropriate personal protective equipment, including safety glasses.
  • Do not use switching power supplies, transformers, chargers, or water batteries as power sources for the spot welder, as this will damage the control circuit.
  • Keep the device away from flammable materials.

3. Package Contents

The kit may come in different packages. Please verify your package contents against the list below:

Package 1 (Control Board Only)

  • Main board: 1

Package 2 (Basic Kit)

  • Main board: 1
  • Welding pen: 2
  • Connection line: 2
  • Heat shrink tubing: 2
  • Nickel sheet: 1
  • Screw: 4

Package 3 (Full Kit with Shell)

  • Main board: 1
  • Welding pen: 2
  • Connection line: 2
  • Heat shrink tubing: 2
  • Nickel sheet: 1
  • Screw: 4
  • Shell: 1

Package 4 (Only Shell)

  • Shell: 1
Spot Welder Kit Components
Image displaying the components included in the 'Spot Welder Set' package: the control board, two welding pens, two connection lines, heat shrink tubing, nickel sheet, and screws.

4. Specifications

ParameterValue
Product Modela99
Working Voltage12V
Working Current100-300A
Standby Power Consumption<0.5mA
Welding Nickel Plate Thickness0.1-0.3mm (related to battery rate)
Welding Peak Current1500A max
MOS Transistors5 (in parallel)
Wire Gauge10AWG
Welding Needle MaterialAluminum oxide copper

Voltage Requirements for Power Source:

  • 25Ah-60Ah or 30C or higher high rate battery.

5. Setup

  • Lead-acid battery: 12V 20-40AH. For batteries over 45AH, consult customer service for current limiting methods.
  • Aviation model batteries or large monomer: 3S-4S, with a capacity (AH) X discharge multiplier (e.g., 60C discharge rate) between 100-300 is appropriate.
  • 12V automotive EC5 interface starter treasure: Peak current should not exceed 600A.

Wiring Connections:

Refer to the diagram below for correct wiring. Ensure all connections are secure before operation.

Spot Welder Wiring Diagram for Car Starter and Lead-Acid Battery
Diagram showing the 99-speed Digital Spot Welder board with 5 MOS in parallel, and two wiring configurations: one for a car starter (EC5 interface) and another for a lead-acid battery. The diagram labels input/output connections for both setups.

Car Starter/Lithium Battery Pack (EC5 Interface) Connection:

  • Input Positive: Connect to EC5 red wire.
  • Input Negative: Connect to EC5 black wire.
  • Output Positive: Connect to red soldering pencil.
  • Output Negative: Connects to black soldering pencil.

Lead-Acid Battery Connection:

  • Input Negative: Connect to negative battery terminal.
  • Input Positive: Connect to positive battery terminal.
  • Output Positive: Connect to red soldering pencil.
  • Output Negative: Connects to black soldering pencil.
Product Introduction Diagram with Labeled Components
Detailed product introduction diagram labeling key components: MOS temperature detection sensor, digital tube display, decrease key, and On/Off/Mode/Up key.

6. Operating Instructions

Power On/Off and Mode Selection:

  • Use the 'On/Off Key/Mode Key/Up Key' button (labeled in the product introduction diagram) to power on the device and cycle through modes.
  • The digital tube provides a clearer display of current settings.

Adjusting Power Levels (Gears):

  • The spot welder has 99 adjustable power levels (gears), displayed in real-time on the digital tube (0-99).
  • Use the 'Decrease key' and 'Up Key' (part of the On/Off/Mode key) to adjust the power level. '1' is the lowest, and '99' is the highest.
  • Increase the gear to achieve a stronger weld if the melt pool is too small.
99 Gears of Power Adjustment
Image demonstrating the 99 gears of power adjustment feature, showing the digital display and a battery pack being spot welded.

Spot Welding Technique:

  1. Place the nickel sheet on the surface of the battery electrode to be welded.
  2. Use one welding pen to point at an angle to hold the nickel sheet.
  3. Use the other welding pen to lightly touch the nickel sheet at an angle, ensuring the distance between the two pens is minimal.
  4. The control board detects that the welding pens have been placed for 0.5 seconds after triggering the weld.
  5. If the weld is weak or the melt pool is too small, increase the gear setting.
Video demonstrating the spot welding process using the 99 Gears Spot Welder DIY Kit, showing the connection to a battery and the welding of a nickel strip to a battery cell.

7. Maintenance

  • Keep the spot welder clean and free from dust and debris.
  • Regularly inspect the welding pens and connection lines for wear or damage. Replace if necessary.
  • Store the device in a dry, cool place when not in use.

8. Troubleshooting

  • 'UE' Alarm Code Displayed: This indicates that the real-time voltage is not within the safe operating range of 8-17V. Check your power source and ensure it meets the voltage requirements.
  • 'CE' Alarm Code Displayed: This indicates that the MOS tube temperature exceeds 45°C. Allow the device to cool down before continuing operation to prevent damage.
  • Weak Weld / Small Melt Pool: Increase the power level (gear) setting. Ensure the nickel plate thickness is appropriate for the battery rate and that the welding pens are making good contact.
  • No Weld: Check all connections to ensure they are secure. Verify that the power source is adequately charged and meets the specifications.
MOS Tube Temperature Protection
Visual representation of the real-time MOS tube temperature protection, indicating that a 'CE' alarm code will be displayed if the MOS tube temperature exceeds 45 degrees Celsius.

9. User Tips

  • For optimal performance, ensure your power source (battery) is fully charged and capable of delivering the required current.
  • Practice on scrap materials first to find the ideal power setting for your specific welding task and nickel strip thickness.
  • Keep the welding pen tips clean for consistent and strong welds.
  • Understand the DIY nature of this kit; it's designed for users who are comfortable with basic electronics and battery assembly.

10. Warranty and Support

For detailed warranty information, technical support, or further inquiries, please refer to the official product documentation or contact the seller directly. A user manual in PDF format may be available for more comprehensive guidance.

You can find additional item guides and documents, including a user manual in PDF format, by checking the product page or contacting the seller. The PDF document is located at: User manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.