Heltecbms HT-610L Series

Contents

Heltecbms 8S Li-ion/LiFePO4 Battery Management System User Manual

Model: HT-610L Series

Brand: Heltecbms

1. Introduction

This device is an intelligent balancing protection board designed specifically for 6S-10S series lithium batteries, supporting ternary lithium/lithium iron phosphate batteries. Its main advantages include protecting the battery from overcharging, over-discharging, over-current, over-temperature, and short-circuit. It also provides balanced charging to achieve long-term maintenance of the battery through voltage balancing, thereby extending the service life of the battery pack.

The BMS is suitable for series-connected lithium battery packs. Once an individual cell voltage reaches the equilibrium turn-on voltage, the high voltage battery will be balanced until the equilibrium release voltage is reached.

2. Product Overview

Video: Overview of the Heltecbms manufacturing and testing process.

Heltecbms 8S 30A/60A 3.2V BMS boards

Image: Heltecbms 8S 30A and 60A 3.2V BMS boards with balance wires.

Product Model Selection

The currently available models are listed below. Customization for 6-10S series is supported.

ParameterValue
Number of strings6S-10S
Current30A/60A
Applicable batteryNCM/LFP

Product Model Description Example

Using a 30A protective board with 10 strings as an example:

  • HT-610 LOS 10S 30A
  • HT-610 LPS 8S 30A

Decoding the model number:

  • 610: Indicates this series can produce 6 to 10 strings.
  • LOS: Indicated for NCM battery (Ternary Lithium).
  • LPS: Indicated for LFP battery (Lithium Iron Phosphate).
  • 10S: The number of strings of this BMS board.
  • 30A: The discharge current of this BMS board.

3. Specifications

General Product Properties

  • High-concerned chemical: None
  • Balance Function: Passive Balanced BMS
  • Type: LI-ION Battery BMS
  • Function: Overcharge Protection, Over Discharge Protection
  • Feature1: Factory direct sale bms
  • Feature2: ebike bms
  • Certification: CE
  • Handware or Smart: Handware BMS
  • Charge and Discharge Port: Common Port BMS
  • Usage Scenario: Power BMS, Energy Storage BMS

Lithium Iron Phosphate (LiFePO4) Parameters

Test conditions: room temperature 25°C. The over-current value and internal resistance are dynamic parameters. The voltage of each battery cell needs to be ≥ 3.25 V during testing.

ProjectSymbolDetailed ContentStandard
Serial numberSNumber of battery strings8S
Current that the shield can withstandA30/60A
Battery typeTernary lithium / lithium iron phosphatelithium iron phosphate
Overcharge detection voltageVDET13.65V±0.035V
Overcharge detection delay timetVDET11.3s (MAX)
Overcharge relieve voltageVREL13.55V±0.025V
Over discharge test voltageVDET22.350V±0.025V
Delay time for over discharge detectiontVDET21.5s (MAX)
Over discharge relieve voltageVREL22.55V±0.025V relieve
Discharge over-current detection voltageVDET321mV±5mV
Instantaneous single pulse current (30A continuous)IDPTheoretical value (battery voltage=3.6V, MOSFET temp 20-45°C)200A
Instantaneous single pulse current (60A continuous)IDPTheoretical value (battery voltage=3.6V, MOSFET temp 20-45°C)400A
Instantaneous multi-pulse current (30A continuous)IDp120A
Instantaneous multi-pulse current (60A continuous)IDp240A
Duration6-10s
Protection release conditionBreak short circuit
Short-circuit protection conditionsExternal load circuit short circuit
Detection delay timeTSHORT300µS (MAX)
Protection release conditionsBreak short circuit
Main circuit on state resistance (battery voltage=3.4V)RDSB- to P- RDS≤1.2/0.8mΩ
Internal consumption of the circuit during operationIDDMIN: 0.3µA MAX: 100µA
Electricity balance detection voltageVBU3.45V±0.035V
Balance startup delay timetVBU1.6S (MAX)
Battery balance release voltageVBL3.44V±0.035V
3.45V battery balance currentIB67mA±5mA
Over-temperature protection (Charging optional)Low temperature -0°C± 5°CNo
MAX continuous working current (Charge)The rated current of the charger when charging the battery pack30A/60A (Equivalent to A of the protective board)
MAX continuous working current (Discharge)The rated current of the battery pack when discharging the load30A/60A (Equivalent to A of the protective board)
Charger selectionVoltage=Number of strings × 3.65V ± 0.05V30A/60A (Equivalent to A of the protective board)
Charging MOS MAX withstand voltageVDSDC 42V

Ternary Lithium Parameters

Test conditions: room temperature 25°C. The over-current value and internal resistance are dynamic parameters. The voltage of each battery cell needs to be ≥ 3.6 V during testing.

ProjectSymbolDetailed ContentStandard
Serial numberSNumber of battery strings6S/7S/10S
CurrentAMax continuous current30/60A
Battery typeTernary lithium / lithium iron phosphateTernary lithium
Overcharge detection voltageVDET14.25V±0.035V
Overcharge detection delay timetVDET11.3s (MAX)
Overcharge relieve voltageVREL14.19V±0.025V
Over discharge test voltageVDET22.8V±0.025V
Delay time for over discharge detectiontVDET21.5s (MAX)
Over discharge relieve voltageVREL23.0V±0.025V relieve
Discharge over-current detection voltageVDET321mV±5mV
Instantaneous single pulse current (30A continuous)IDPTheoretical value (battery voltage=3.6V, MOSFET temp 20-45°C)200A
Instantaneous single pulse current (60A continuous)IDPTheoretical value (battery voltage=3.6V, MOSFET temp 20-45°C)400A
Instantaneous multi-pulse current (30A continuous)IDp120A
Instantaneous multi-pulse current (60A continuous)IDp240A
Duration5-10s
Protection release conditionBreak short circuit
Short-circuit protection conditionsExternal load circuit short circuit
Detection delay timeTSHORT300µS (MAX)
Protection release conditionsBreak short circuit
Main circuit on state resistance (battery voltage=3.4V)RDSB- to P- RDS≤1.2/0.8mΩ
Internal consumption of the circuit during operationIDDMIN: 0.3µA MAX: 100µA
Electricity balance detection voltageVBU4.2V±0.035V
Balance startup delay timetVBU1.6S (MAX)
Battery balance release voltageVBL4.19V±0.035V
3.59V battery balance currentIB90mA±5mA
Over-temperature protection (Charging optional)High temperature 75°C± 5°CNO
MAX continuous working current (Charge)The rated current of the charger when charging the battery pack30A/60A (Equivalent to A of the protective board)
MAX continuous working current (Discharge)The rated current of the battery pack when discharging the load30A/60A (Equivalent to A of the protective board)
Charger selectionVoltage=Number of strings × 3.65V ± 0.05V30A/60A (Equivalent to A of the protective board)
Charging MOS MAX withstand voltageVDSMAX voltage value that the charger can withstand when the charging port is connectedDC 42V

4. Dimensions

The length and width of the 6-10S series protection board are consistent, while the thickness varies according to the current rating.

BMS board dimensions and thickness table

Image: Diagram showing the 63mm x 48mm dimensions and a table indicating thickness (5.5mm for 30A, 9mm for 60A).

5. Setup and Wiring

Proper wiring is crucial for the safe and effective operation of the BMS. Always ensure all connections are secure and correct before applying power.

General BMS wiring diagram

Image: General wiring diagram for a Battery Management System, showing connections for Battery -, Pack+, Charge/Discharge +, and balance leads.

Specific Wiring Diagrams:

6S BMS Wiring Diagram

Image: Wiring diagram for a 6S BMS, illustrating connections for battery cells, charger, and controller.

7S BMS Wiring Diagram

Image: Wiring diagram for a 7S BMS, illustrating connections for battery cells, charger, and controller.

8S BMS Wiring Diagram

Image: Wiring diagram for an 8S BMS, illustrating connections for battery cells, charger, and controller.

10S BMS Wiring Diagram

Image: Wiring diagram for a 10S BMS, illustrating connections for battery cells, charger, and controller.

6. Operating Instructions

The Heltecbms HT-610L series BMS operates automatically to provide essential protection and balancing functions for your battery pack. Once correctly installed and connected, the BMS continuously monitors the battery cells.

Protection Functions:

TypeOvercharge single string detection voltageOvercharge single string release voltageOver-discharge single string detection voltageOver-discharge single string release voltageSingle string balanced charging start
NCM4.25V±0.035V4.19V±0.025V2.8V±0.025V3.0V±0.025V4.2V±0.035V
LFP3.65V±0.035V3.55V±0.025V2.35V±0.025V2.55V±0.025V3.45V±0.035V

The BMS will automatically engage these protection mechanisms to prevent damage to the battery pack and ensure its longevity. Balancing occurs when cell voltages reach the specified threshold, ensuring all cells are maintained at optimal levels.

7. Product Accessories

The Heltecbms HT-610L series BMS typically includes the following accessory:

BMS with collection line

Image: Heltecbms BMS board with the included collection line (balance wires).

  • Collection line x1: This is the balance wire harness used to connect to individual battery cells for voltage monitoring and balancing.

8. Maintenance

To ensure the long-term performance and reliability of your Heltecbms BMS and battery pack, consider the following maintenance guidelines:

  • Regular Inspection: Periodically check all wiring connections for tightness and signs of corrosion or damage.
  • Environmental Conditions: Operate the battery pack and BMS within recommended temperature ranges. Avoid extreme heat or cold, which can degrade performance and lifespan.
  • Cleanliness: Keep the BMS board clean and free from dust, moisture, and conductive debris.
  • Avoid Physical Damage: Protect the BMS from physical impact or excessive vibration.
  • Proper Storage: If storing the battery pack for an extended period, ensure it is charged to a recommended storage voltage (e.g., 50% state of charge) and stored in a cool, dry place.

9. Troubleshooting

This section provides guidance on common issues and their potential solutions. If you encounter problems not listed here or cannot resolve an issue, please contact customer service.

Fault PhenomenonFault Inspection and CauseProcessing Method
Can't dischargeFirst, connect the circuit to activate the protection board for charging, and then measure the voltage of each battery separately. If the voltage of any battery is lower than 3.0V±0.025V (NCM) / 2.35V±0.025V (LFP), the protection board will start over-discharge protection.If the battery is lower than 3.0V, please charge the battery to 3.6V (NCM) / 3.25V (LFP) and balance it before combining. Do not mix good batteries with poor batteries (if you cannot solve this problem, please contact after-sales service).
Can't chargeMeasure the voltage of each battery section. If any battery voltage is higher than 4.215V (NCM) / 3.615V (LFP) or so, the protection board will start overcharge protection.If the battery is higher than 4.215V (NCM) / 3.615V (LFP), please discharge the battery to about 3.7V until it is balanced before combining. Do not mix good batteries with poor batteries (if you cannot solve this problem, please contact after-sales).
Charging/discharge failureB-, B1, B2, B3, ...... B+ Wrong wiringRedraw the wiring or operate under the guidance of customer service.
Overcharge/discharge protection is invalidB-, B1, B2, B3, ...... B+ Wrong wiringRedraw the wiring or operate under the guidance of customer service.
Discharge protectionCheck whether the current value of the load starting power supply exceeds the over-current protection current of the protection board.Replace the protection board with a larger current (if not solved, please contact after-sales).
Components welded looselyOne of the components has a pin that is not connected to the PCB pad.You can repair the welding by yourself (if it still cannot be solved, please contact after-sales).
Component weldingThere is a short circuit between two or more pins of the element.Remove the component and re-weld (if not, please contact after-sales).
Electrostatic breakdownWhen the MOS tube is not powered, the forward and reverse resistance of any two pins of the G, D and S terminals are 0.You can remove and replace the MOS tube by yourself (if it still cannot be solved, please contact after-sales).

Our company guarantees that each product is shipped after being tested by professional protection board testing instruments. However, due to the combination battery of the protection board potentially being damaged by static electricity and current, it is normal to have defective products in use.

10. User Tips

  • The Heltecbms HT-610L series is suitable for building 24V battery packs, for example, using four 30-amp batteries to create a 24V system for an electric bicycle.
  • Users have noted the product's good appearance and timely delivery.
  • General feedback indicates satisfaction with the product's functionality.

11. Warranty and Support

Warranty Regulations

The warranty service period for this product is 1 year.

The warranty service is limited to normal use. The following conditions are not covered under free warranty:

  • Man-made damage.
  • Self-disassembly, modification, and unauthorized repair.
  • Use not in accordance with the instructions.
  • Damage caused by external force majeure factors.

Accessories such as test fixtures are considered consumables and are not covered by warranty.

Support

If you require warranty service, please contact your dealer for processing. If you cannot contact the dealer, you can reach our company by email or phone.

Please note that there are no after-sales service stations in other countries except China. If warranty service is needed, you will need to send the product to us for free repair, but you will be responsible for the round-trip freight.

© 2024 Heltecbms. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.