Heltecbms HT-610L Series

Contents

Heltecbms HT-610L Series Battery Management System User Manual

Models: 6S, 7S, 8S, 10S Li-ion & LiFePO4 (30A/60A)

1. Product Introduction

The Heltecbms HT-610L Series is an intelligent balancing protection board designed specifically for 6S-10S series lithium batteries. It supports both ternary lithium (Li-ion) and lithium iron phosphate (LiFePO4) battery types.

Main advantages:

  • Protection against overcharging, over-discharging, over-current, over-temperature, and short circuits.
  • Balanced charging to maintain battery health and extend service life through voltage equalization.

This BMS is suitable for series-connected lithium battery packs. It ensures that once an individual cell voltage reaches the equilibrium turn-on voltage, the high voltage battery will be balanced until the equilibrium release voltage is achieved.

Video: Heltecbms production facility showcasing manufacturing and testing processes.

2. Product Model Selection & Description

The HT-610L series offers various configurations based on the number of strings and current capacity. The model naming convention provides clear identification:

  • HT-610 LOS 10S 30A: 610 (series), LOS (NCM battery), 10S (10 strings), 30A (discharge current).
  • HT-610 LPS 8S 30A: 610 (series), LPS (LFP battery), 8S (8 strings), 30A (discharge current).

Available models support 6S-10S configurations with 30A or 60A current ratings for NCM (Li-ion) or LFP (LiFePO4) batteries.

Various Heltecbms HT-610L BMS models including 8S 30A 3.2V, 10S 30A 3.7V, 6S 60A 3.7V, and 7S 30A 3.7V.
Image: Overview of different Heltecbms HT-610L BMS models.
Heltecbms 10S 60A and 10S 30A 3.7V BMS boards with connection details.
Image: Heltecbms 10S 30A and 60A 3.7V Li-ion BMS boards.
Heltecbms 6S 30A and 6S 60A 3.7V BMS boards with pre-attached wiring harnesses.
Image: Heltecbms 6S 30A and 60A 3.7V Li-ion BMS boards.
Heltecbms 7S 60A 3.7V BMS board with pre-attached wiring harness.
Image: Heltecbms 7S 60A 3.7V Li-ion BMS board.

3. Specifications and Parameters

The following tables detail the electrical parameters for both LiFePO4 and Ternary Lithium (Li-ion) versions of the HT-610L series BMS. All tests are conducted at room temperature (25°C).

3.1. LiFePO4 Battery BMS Parameters

ProjectSymbolDetailed ContentStandard
Serial numberSNumber of battery strings8S
CurrentAMax continuous current30A/60A
Battery typeTernary lithium / lithium iron phosphatelithium iron phosphate
Overcharge detection voltageVDET13.65V±0.035V
Overcharge detection delay timetVDET11.3s (MAX)
Overcharge relieve voltageVREL13.55V±0.025V
Over discharge test voltageVDET22.350V±0.025V
Delay time for over discharge detectiontVDET21.5s (MAX)
Over discharge relieve voltageVREL22.55V±0.025V relieve
Discharge over-current detection voltageVDET321mV±5mV
Instantaneous single pulse current (30A/60A)IDPTheoretical value (battery voltage 3.6V, MOSFET temp 20-45°C)200A/400A
Instantaneous multi-pulse current (30A/60A)IDP120A/240A
Duration6-10s
Short-circuit protection release conditionBreak short circuit
Short-circuit detection delay timeTSHORT300µS (MAX)
Internal resistance (B- to P-)RDSMain circuit on state resistance (battery voltage=3.4V)≤1.2/0.8mΩ
Consume currentIDDInternal consumption of the circuitMIN: 0.3µA MAX: 100µA
Electricity balance detection voltageVBU3.45V±0.035V
Balance startup delay timetVBU1.6S (MAX)
Battery balance release voltageVBL3.44V±0.035V
3.45V battery balance currentIB67mA±5mA
Charging MOS MAX withstand voltageVDSDC 42V

3.2. Ternary Lithium (Li-ion) Battery BMS Parameters

ProjectSymbolDetailed ContentStandard
Serial numberSNumber of battery strings6S/7S/10S
CurrentAMax continuous current30A/60A
Battery typeTernary lithium / lithium iron phosphateTernary lithium
Overcharge detection voltageVDET14.25V±0.035V
Overcharge detection delay timetVDET11.3s (MAX)
Overcharge relieve voltageVREL14.19V±0.025V
Over discharge test voltageVDET22.8V±0.025V
Delay time for over discharge detectiontVDET21.5s (MAX)
Over discharge relieve voltageVREL23.0V±0.025V relieve
Discharge over-current detection voltageVDET321mV±5mV
Instantaneous single pulse current (30A/60A)IDPTheoretical value (battery voltage 3.6V, MOSFET temp 20-45°C)200A/400A
Instantaneous multi-pulse current (30A/60A)IDP120A/240A
Duration6-10s
Short-circuit protection release conditionBreak short circuit
Short-circuit detection delay timeTSHORT300µS (MAX)
Internal resistance (B- to P-)RDSMain circuit on state resistance (battery voltage=3.4V)≤1.2/0.8mΩ
Consume currentIDDInternal consumption of the circuitMIN: 0.3µA MAX: 100µA
Electricity balance detection voltageVBU4.2V±0.035V
Balance startup delay timetVBU1.6S (MAX)
Battery balance release voltageVBL4.19V±0.035V
3.59V battery balance currentIB90mA±5mA
Charging MOS MAX withstand voltageVDSDC 42V

4. Dimensions

The length and width of the 6-10S series protection board are consistent across models. The thickness varies depending on the current rating.

CurrentThickness (MM)
30A5.5
60A9
Diagram showing the dimensions of a Heltecbms BMS board, with a length of 63mm and width of 48mm.
Image: Dimensions of the BMS board (Length: 63mm, Width: 48mm).

5. Wiring Diagrams

Proper wiring is crucial for the safe and effective operation of your Battery Management System. Always check the series sequence of batteries and connect the wiring in strict accordance with the drawing before inserting the board.

Detailed wiring diagrams for 6S, 7S, 8S, and 10S BMS configurations, showing connections for Battery-, P-, Charger, and individual cell balance leads.
Image: Comprehensive wiring diagrams for 6S, 7S, 8S, and 10S BMS. Note: Check the series sequence of batteries and connect the wiring in strict accordance with the drawing and confirm that it is correct before inserting the board.

6. Protection Functions

The HT-610L series BMS provides robust protection features for your battery pack. The table below outlines the key protection parameters for both NCM (Li-ion) and LFP (LiFePO4) battery types.

TypeOvercharge single string detection voltageOvercharge single string release voltageOver-discharge single string detection voltageOver-discharge single string release voltageSingle string balanced charging start
NCM4.25V±0.035V4.19V±0.025V2.8V±0.025V3.0V±0.025V4.2V±0.035V
LFP3.65V±0.035V3.55V±0.025V2.35V±0.025V2.55V±0.025V3.45V±0.035V

7. Product Accessories

Each HT-610L series BMS board typically includes a corresponding collection line for connecting to individual battery cells.

Heltecbms 7S 30A 3.7V BMS board and its accompanying collection line.
Image: BMS board (7S 30A 3.7V shown) and its collection line.

8. Troubleshooting

If you encounter issues with your BMS, refer to the table below for common fault phenomena, their causes, and recommended processing methods.

Fault PhenomenonFault Inspection and CauseProcessing Method
Cannot dischargeProtection board started over-discharge protection because one or more battery cells are below 3.0V±0.025V (NCM) / 2.35V±0.025V (LFP).Charge the battery to 3.6V (NCM) / 3.25V (LFP) and balance it before combining. Do not mix good batteries with poor ones. Contact after-sales service if unresolved.
Cannot chargeProtection board started overcharge protection because one or more battery cells are higher than 4.215V (NCM) / 3.615V (LFP).Discharge the battery to about 3.7V until it is balanced before combining. Do not mix good batteries with poor ones. Contact after-sales service if unresolved.
Charging/discharge failureIncorrect wiring (B-, B1, B2, B3...B+).Redraw the wiring or operate under the guidance of customer service.
Overcharge/discharge protection is invalidIncorrect wiring (B-, B1, B2, B3...B+).Redraw the wiring or operate under the guidance of customer service.
Discharge protectionLoad starting power supply current exceeds the over-current protection current of the board.Replace the protection board with a larger current rating. Contact after-sales service if unresolved.
Components welded looselyA component pin is not connected to the PCB pad.Repair the welding yourself. Contact after-sales service if unresolved.
Component weldingShort circuit between two or more pins of an element.Remove the component and re-weld. Contact after-sales service if unresolved.
Electrostatic breakdownMOS tube is not powered; forward and reverse resistance of any two pins of G, D, and S terminals are 0.Remove and replace the MOS tube yourself. Contact after-sales service if unresolved.

9. User Tips

  • Activation: Some users have noted that the BMS board may require activation upon initial installation to function correctly.
  • External Start: The BMS is reported to work without an external start, simplifying setup for some applications.
  • Thermal Management: Consider replacing the factory-supplied thermal pads with higher quality alternatives for improved heat dissipation, especially for 60A models or high-power applications.
  • Solder Quality: Inspect solder joints on contacts and tracks. Some users have observed areas with insufficient solder coverage, which may require touch-up for optimal performance.
  • Temperature Control: If temperature control is a critical feature for your application (e.g., for 7S 60A boards), inquire about the optional temperature sensor or customization options.

10. Warranty and Support

The warranty service period for this product is 1 year.

Warranty Limitations:

  • The warranty is limited to normal use.
  • Man-made damage, self-disassembly, modification, or repair not in accordance with instructions will void the warranty.
  • Damage caused by external force majeure factors is not covered.
  • Accessories such as test fixtures are considered consumables and are not covered by warranty.

For warranty service, please contact your dealer. If you cannot reach your dealer, you may contact Heltecbms directly via email or phone.

Please note that there are no after-sales service stations in other countries except China. For warranty service requiring product return, you will be responsible for the round-trip freight costs.

For a complete and detailed user manual, please refer to the official PDF document: Heltecbms HT-610L Series Battery Management System User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.