zemismart SDM02T

Contents

Zemismart SDM02T Zigbee 120A 2 Phase Energy Meter User Manual

Smart Din-rail Power Monitor with Withdrawable Split-core CTs

Zemismart SDM02T Zigbee 120A 2 Phase Energy Meter

1. Introduction

The Zemismart SDM02T is a smart energy monitor designed for din-rail installation, capable of measuring energy consumption for up to two circuits simultaneously. It provides real-time data on current, voltage, and power, helping you understand and manage your electricity usage. This device integrates with Tuya Zigbee Hubs or Zigbee2MQTT dongles for smart home monitoring via the Tuya APP or Home Assistant.

2. Important Safety Information

Please read all safety warnings and instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, serious injury, or equipment damage.

  • Professional Installation: SDM02T sensors must ONLY be installed and maintained by qualified professionals.
  • Inspection: Do not install if any damage is observed during unpacking.
  • Enclosure: Sensors must be installed inside electrical panels or switchboards, behind a door or plate, inaccessible to unauthorized persons.
  • Panel Standards: Electrical panels must meet IEC 61439-1 and comply with IEC 61140 installation and safety rules.
  • Power Disconnection: Turn off all power supply sources before installing and during maintenance.
  • Voltage Verification: Always use a properly rated voltage sensing device to confirm power is off. Do not use the SDM02T for voltage testing; use a dedicated voltage tester.
  • Fire Hazard: The SDM02T must be associated with an easily accessible upstream protection and circuit-breaker system.
  • Cable Adjustment: The ends of voltage take-off cables must be adjusted to the corresponding equipment and device by qualified professionals only.

3. Package Contents

Please check the package for the following items:

  • 1x SDM02T Smart Energy Monitor (Monitoring Module)
  • 2x Split-core Current Transformers (CTs) (Detection Modules)
  • 1x User Manual

4. Specifications

FeatureSpecification
Model NumberSDM02T
Item TypeSWITCHES (Energy Monitor)
Brand Namezemismart
Is Smart DeviceYes
MaterialPlastic
OriginMainland China
CertificationCE
Rated Operating Voltage (Un)110~240 VAC L-N, 50/60 Hz
Max Current (Imax)120 A / 200 A (per CT)
Over-voltage CategoryIII
Rated Isolating Voltage (Ui)250 V
Rated Impulse Withstand Voltage (Uimp)4 kV
Pollution Degree3
Protection DegreeIP20
Energy Measurement Accuracy ClassClass 1 (IEC61557-12)
Rated Operating Temperature-25~70 °C
Maximum Power Consumption≤ 2 VA

5. Setup and Installation

5.1 Wiring Diagram

The following diagram illustrates the connection of the SDM02T monitor and split-core CTs to your electrical system. Ensure all connections are made by a qualified professional with power disconnected.

Zemismart SDM02T Wiring Diagram

Figure 1: SDM02T Wiring Diagram. Shows the monitor connected to L1, L2, and N, with CTs around the L1 and L2 lines after the upstream protection device.

Application Illustration for CT Placement

Figure 2: Application Illustration. Shows the direction of current flow for CTs (I1, I2) and their connection to the monitor. Note: SDM02 can only be installed upstream if associated with a contactor, frequency converter or motor starters.

5.2 Installation Steps

  1. Voltage Wire Connection: Insert the voltage wire (L1, L2, N) into the pluggable terminals of the monitoring module. Ensure the N pole of the voltage measurement connector is NOT connected to phase voltage.
  2. Current Transformer Wire Connection: Insert the wires from the split-core current transformers (CTs) into the corresponding pluggable terminals (I1, I2) on the monitoring module.
  3. Install Current Transformers: Install the split-core CTs around the live wires (L1 and L2) of the circuits you wish to monitor. Ensure the CTs are not in direct contact with non-insulated conductors. The arrow on the CT indicates the positive energy flow direction.
  4. Secure CTs: To guarantee measurement accuracy, it is recommended to keep the conductor adherent to the CT body using two fixing straps.
  5. Phase Matching: Assemble correctly the correspondent phase to CT line (e.g., L1 with CT1, L2 with CT2).

Important Note: Voltage measurement must match current measurement (V1 with I1, V2 with I2) for correct electrical data. Connecting the blue cable for N connection to phase conductors by mistake can cause product damage.

5.3 App Setup and Pairing

The SDM02T requires a Tuya Zigbee Hub or Zigbee2MQTT dongle for smart functionality. These are not included with the product.

Tuya Zigbee Hub or Zigbee2MQTT Dongle Required

Figure 3: Tuya Zigbee Hub or Zigbee2MQTT dongle is required for connectivity.

  1. App Installation: Ensure you have the latest version of the Smart Life app downloaded and installed on your mobile phone.
  2. Zigbee Gateway Setup: If your device is the Zigbee version, ensure your Tuya Smart Zigbee gateway is properly installed and connected to the app.
  3. Network Connection: Connect your mobile phone to the same wireless network as your Zigbee gateway.
  4. Add Device: Open the Smart Life app, tap "Home", then tap "+" in the top right corner to enter the "Add Device" page.
  5. Pairing Mode: On the SDM02T monitor, press the reset button until the LED quickly flashes (2Hz) to enter pairing mode.
  6. Device Discovery: The app will scan for smart devices to be configured. Once the SDM02T sensor appears, follow the in-app prompts to complete the pairing process.

6. Operating the Device

Once successfully paired, you can monitor your energy consumption in real-time through the Smart Life app or Home Assistant.

6.1 Real-time Monitoring (Tuya APP)

The Tuya app provides a comprehensive interface to view key electrical data for both L1 and L2 circuits.

Tuya APP Control Interface

Figure 4: Tuya APP Control. Displays current (A), active power (kW), voltage (V) for L1 and L2, total active power, overall power factor, and frequency.

6.2 Real-time Monitoring (Home Assistant)

If using a Zigbee2MQTT dongle, all data becomes accessible for monitoring through Home Assistant.

Home Assistant Real-time Monitoring

Figure 5: HA Real-time Monitoring. Shows voltage, power, and current for phases A and B within Home Assistant.

6.3 Device Settings and Data Reporting

On the device settings page within the app, you can access more detailed data and configure reporting intervals.

More Data Settings in App

Figure 6: More Data. Access settings like "Device Locating", "Interval for Data Reporting" (range 5 ~ 3600 seconds), and view detailed L1 and L2 electricity data including current, active power, power factor, forward active energy, and reverse active energy.

Video 1: Zemismart SDM02T Product Overview. This video demonstrates the physical product, its components, and a brief overview of its features and installation.

7. Maintenance

  • Keep the device clean and free from dust.
  • Ensure proper ventilation around the device if installed in an enclosed space.
  • Regularly check wiring connections for tightness and signs of wear.
  • Do not use abrasive cleaners or solvents on the device.

8. Troubleshooting (Indicator Light Description)

Status LEDDescriptionAction
ON (Solid)Normal using, connected to cloudNo action required.
Flashing at 2HzIn pairing modePress reset button until LED quickly flashes to enter pairing mode.
Flashing at 0.5HzPaired, searching for cloud (not connected to wireless network)Check network connection and Zigbee gateway status.
Flashing at 1HzWireless communication failed (cannot communicate with cloud)Check supply voltage (too low?) and network connection.
Flashing at 0.25HzSelf-checking failedRestart the device: disconnect power, switch on, then repair.
Flashing at 1HzAlarm notification activeCheck device wiring and alarm information in the app.

9. User Tips

  • Zigbee2MQTT Compatibility: Users have reported successful operation with Zigbee2MQTT.
  • ZHA Compatibility: Some users have noted that the device may not work with ZHA (Zigbee Home Automation).
  • Version Check: Always verify you have received the correct version (Zigbee or Wi-Fi) as ordered, as some users have received the incorrect version.

10. Frequently Asked Questions (FAQ)

Q: Is this item Wi-Fi or Zigbee?
A: The Zemismart SDM02T is available in both Wi-Fi and Zigbee versions. Please ensure you select the correct version when purchasing. This manual primarily covers the Zigbee version's setup with a Zigbee hub.
Q: What is the function of “Device Locating”?
A: The “Device Locating” function, found in the app's 'More Data' settings, is typically used to help identify the physical location of the device among multiple similar devices, often by triggering a visual indicator or sound on the device itself (if supported) or simply for organizational purposes within the app interface.

11. Warranty and Support

For warranty information and technical support, please refer to the seller's official website or contact their customer service directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.