RETEVIS RB48

Contents

Retevis RB48 Heavy Duty Walkie Talkie User Manual

Two Retevis RB48 walkie-talkies, highlighting IP67 waterproof and heavy-duty features. One radio is shown partially submerged in water.

Retevis RB48: IP67 Waterproof Heavy Duty Walkie Talkie

1. Important Safety Information

Please read all safety instructions carefully before using your radio. Failure to follow these instructions may result in injury or damage to the device.

  • Do not charge the radio in flammable or explosive environments.
  • Do not operate the radio in areas where radio communication is prohibited (e.g., oil stations, gas stations, airports).
  • Avoid direct sunlight and placing the radio near heating devices.
  • If the radio emits smoke or an unusual smell, immediately remove the battery pack and contact support.
  • Only qualified professionals should perform repairs; do not attempt to disassemble the radio.
  • Protect your hearing: Use the lowest necessary volume, turn down volume before adding earpieces, and limit high-volume use.
  • Avoid burns: Do not use radios with damaged antennas. Handle batteries carefully to prevent short circuits.

2. Product Overview

2.1 Radio Components

  1. Antenna: For transmitting and receiving signals.
  2. Call Tone Button: Short press for call tone; long press for NOAA weather (US version).
  3. PTT (Push-to-Talk) Button: Press to transmit, release to receive.
  4. Menu/Lock Button: Short press to enter menu; long press to open/close key lock (US version).
  5. Up Button: Navigate up in menus, increase values.
  6. Down Button: Navigate down in menus, decrease values.
  7. Earpiece Jack: For connecting external audio accessories.
  8. Volume/Power Switch: Rotate to turn on/off and adjust volume.
  9. LED Display: Shows channel, status, and icons.
  10. Scan/Monitor Button: Short press to switch scan function; long press to switch monitor.
  11. Alarm Button: Activates alarm function.
  12. PTT (Side): Secondary Push-to-Talk button.
  13. Type-C Port: For direct charging.

2.2 LCD Display Icons

  • 2CH: Channel number display.
  • SCAN: Scan function active.
  • HI/LO: High or Low power setting.
  • VOX: Voice Operated Transmit function active.
  • Battery Indicator: Shows current battery level.
  • Lock Icon: Keypad is locked.
  • SOS: Alarm function active.
  • Weather Icon: NOAA Weather mode active.

3. Setup Guide

3.1 Unboxing

Your package should contain:

  • Retevis RB48 Walkie Talkie unit(s)
  • Rechargeable Li-ion Battery Pack(s)
  • Belt Clip(s)
  • Desktop Charger Base(s) (if applicable)
  • USB Type-C Charging Cable(s)
  • User Manual

3.2 Battery Installation

Ensure the radio is turned off. Align the battery pack with the battery compartment on the back of the radio. Gently push the battery until it clicks into place. To remove, slide the battery release latch and pull the battery pack away.

3.3 Charging the Battery

The RB48 offers multiple charging methods:

  1. Using the Desktop Charger: Place the radio (with battery installed) into the desktop charger base. Ensure the charging contacts align. The indicator light on the charger will show charging status.
  2. Using the Direct Type-C Charger: Open the rubber cover on the side of the radio to expose the Type-C port. Insert the USB Type-C cable.

Important Charging Notes:

  • Use only the matching charging base or Type-C cable provided.
  • Ensure the radio is turned off during charging.
  • For optimal battery performance, charge for at least 5 hours for the first time.
  • Do not overcharge the battery; stop charging once fully charged to prolong battery life.
  • The battery may become slightly warm during charging, which is normal.
Retevis RB48 charging options: desktop charger for two units and direct USB Type-C charger for individual units.

Multi-Charger Way: Desktop Charger and Direct Type-C Charger

3.4 Powering On/Off

Rotate the Volume/Power Switch (8) clockwise to turn on the radio. You will hear a power-on prompt, and all icons will briefly display on the screen. Rotate counter-clockwise until a click sounds to turn off the radio.

4. Operating Instructions

4.1 Volume Adjustment

In standby or receiving mode, rotate the Volume/Power Switch (8) clockwise to increase volume and counter-clockwise to decrease volume. Volume levels 1-9 can be adjusted. Avoid placing the speaker too close to your ear if the volume is too high.

4.2 Transmit and Receive

  1. To Transmit: Press and hold the PTT button (3 or 12) and speak into the microphone. The transmit icon will appear on the display. Keep the radio in a vertical position, 3-5cm from your mouth, and at least 3cm from your head/body.
  2. To Receive: Release the PTT button. The receive icon will appear, and you will hear the incoming transmission.

4.3 Setting the Channel

  1. In standby mode, short press the Menu button (4) once. The current channel number will flash.
  2. Use the Up (5) or Down (6) buttons to select the desired channel.
  3. Press the PTT button to save the setting and exit, or press Menu again to move to the next setting.

4.4 CTCSS/DCS Selection

This radio supports 121 groups of CTCSS/DCS codes (38 analog, 83 digital). These can be set via software (CPS).

  1. In standby mode, short press the Menu button (4) twice. The current CTCSS/DCS setting will flash.
  2. Use the Up (5) or Down (6) buttons to select the desired CTCSS/DCS code.
  3. Press the PTT button to save the setting and exit, or press Menu again to move to the next setting.

4.5 High/Low Power Setting

  1. In standby mode, short press the Menu button (4) five times.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.