CETANT PL230

Contents

Nordic LED Wall Lamp User Manual

Model: PL230

Product Overview

The CETANT Nordic LED Wall Lamp (Model PL230) is designed for interior decoration, providing warm white illumination. It features an aluminum body with an acrylic lampshade, available in various colors and textures.

Nordic LED Wall Lamp in various colors, top-down view

Figure 1: Nordic LED Wall Lamp in various colors.

Video 1: Product showcase demonstrating different lampshade colors and their appearance when lit.

Safety Information

  • Always cut off the power supply or close the main circuit breaker before installation, maintenance, or cleaning.
  • Do not install or operate lamps in flammable or humid environments.
  • Ensure all parts and accessories are present and undamaged before beginning installation.
  • If you are unsure about any part of the installation, consult a qualified electrician.

Setup and Installation

This lamp is designed for wall-mounted installation. Please follow these steps carefully:

  1. Prepare for Installation: Ensure the power supply is OFF at the main circuit breaker. Unpack the lamp and check that all parts and accessories are included and undamaged.
  2. Disassemble the Lamp: Unscrew the acrylic lampshade and carefully remove it from the aluminum chassis.
  3. Mark Drilling Locations: Determine the desired location for the lamp on the wall. Place the aluminum chassis against the wall and mark the positions where holes need to be drilled.
  4. Drill Holes: Using an appropriate drill bit for your wall type, drill holes at the marked locations.
  5. Insert Wall Plugs: Push the rubber wall plugs (if provided) into the drilled holes. Use a hammer to gently tap them flush with the wall surface if necessary.
  6. Wire Connection: Connect the electrical wires from your wall to the lamp's connector. Ensure the live wire, ground wire, and neutral wire are connected correctly according to local electrical codes.
  7. Mount Chassis: Use a screwdriver to securely fix the aluminum chassis to the wall using the provided screws.
  8. Attach Lampshade: Carefully screw the acrylic lampshade back onto the aluminum chassis.
  9. Restore Power: Once installation is complete and secure, restore power at the main circuit breaker.

For a visual guide, please refer to the installation procedure diagram in the full user manual PDF: View User Manual (PDF).

Operating Instructions

Once properly installed and connected to power, the lamp will illuminate when the connected wall switch is turned on. This lamp uses integrated LED bulbs and provides warm white light (2700-3500K).

  • Power On/Off: Control the lamp using your standard wall switch.
  • Light Output: The lamp provides a fixed warm white light. It is not dimmable.

Maintenance

To ensure the longevity and appearance of your lamp, follow these maintenance guidelines:

  • Cleaning: Before cleaning, always turn off the power supply to the lamp. Use a soft, dry cloth to wipe the aluminum body and acrylic lampshade. For stubborn marks, a slightly damp cloth with mild soap can be used, followed by drying with a clean, soft cloth.
  • Avoid Harsh Chemicals: Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish of the lamp.
  • Bulb Replacement: The lamp uses integrated LED bulbs, which are not user-replaceable. If the LEDs fail, the entire fixture may need to be replaced.

Troubleshooting

If your lamp is not functioning as expected, please check the following common issues:

  • Lamp Does Not Light Up:
    • Ensure the power supply to the lamp is on at the wall switch and the main circuit breaker.
    • Check all electrical connections to ensure they are secure and correctly wired.
    • If the lamp still does not light up, there may be an internal fault. Contact customer support.
  • Flickering Light:
    • Check for loose wiring connections.
    • Ensure the operating voltage (85V-265V) is within the specified range for your region.

Specifications

Diagram showing dimensions (13.5cm diameter, 7.5cm height) and specifications for the C-Green variant.

Figure 2: Product dimensions and key specifications.

FeatureSpecification
Brand NameCETANT
Model NumberPL230 (also WL144)
Item TypeWall Lamps
StyleModern Style
MaterialAluminum/Acrylic
Body MaterialAluminum
Shade TypeStained Glass (Acrylic)
Shade DirectionUp & Down
Light SourceLED bulbs (Integrated LED*5W)
Color TemperatureWarm White (2700-3500K)
Is Bulbs IncludedYes
Is DimmableNo
Is Smart DeviceNo
Power SourceAC
Voltage90 - 260 V (Operating voltage: 85V-265V)
Luminous Flux249-2000 Lumens
Lighting Area5-10 square meters (Recommended: 3-5m²)
Installation TypeWall Mounted (Assembly)
CertificationCCC, CE, PSE, ROHS
Dimensions (Approx.)Diameter: 13.5 cm, Height: 7.5 cm
Package Weight0.657 kg
Package Dimensions15 cm (L) x 15 cm (W) x 11 cm (H)

User Tips

  • Non-Dimmable: Please note that this lamp is not dimmable and will operate at a fixed brightness.
  • Placement: Ideal for bedrooms, living rooms, foyers, and study areas.

Warranty and Support

This product comes with a 2-year warranty from the date of purchase.

For any issues, questions, or warranty claims, please contact the seller or retailer from whom you purchased the product. Provide your order details and a description of the issue for prompt assistance.

For the complete user manual and detailed diagrams, please refer to the PDF document: View User Manual (PDF).

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.