1. Introduction
This manual provides comprehensive instructions for the safe and effective installation, operation, and maintenance of your S5-#124 LED Car Door Welcome Light Projector. This product is designed to project a high-definition logo onto the ground when your car door is opened, enhancing the aesthetic appeal and visibility around your vehicle. Please read this manual thoroughly before installation and keep it for future reference.

2. Specifications
The S5-#124 LED Car Door Welcome Light Projector is engineered for durability and performance. Key features include:
- Plug and Play: Easy installation without complex wiring.
- Durable Construction: Built to last.
- Cooling Design: Prevents overheating for prolonged use.
- HD Projection: Clear and sharp logo imaging.
- High-Definition Lens: Ensures clear, colorful imaging with no image blur.

2.1 Technical Parameters
| Parameter | Value |
|---|---|
| Item Type | Welcome Light |
| Material | PC + LED |
| Input Power | 5W (each LED bulb) |
| Rated Voltage | DC 12V / 24V |
| Operating Temperature | -40°C to 80°C |
| Waterproof Rating | IP68 Certified (Rain-Proof design) |
| Dimensions (Approx.) | Length: 6.3cm (2.48in), Width: 3.8cm (1.50in), Height: 2.9cm (1.14in) |


2.2 Applicable Models
This product (Model S5-#124) is compatible with the following Skoda vehicle models and years:
- Skoda Yeti: 2012-2017
- Skoda Octavia: 2015-2024
- Skoda Karoq: 2017-2024
- Skoda Kodiaq: 2016-2024
Note: Before purchasing or installing, please carefully confirm your vehicle's corresponding model and year to ensure compatibility.

3. Setup and Installation
The S5-#124 LED Car Door Welcome Light Projector is designed for nondestructive installation, directly replacing your vehicle's original door lights. No drilling or wiring modifications are typically required.
3.1 Installation Steps
- Remove Original Lamp: Gently pry out the original door lamp from its slot. Use a plastic trim removal tool to avoid scratching your car's paint or interior.
- Disconnect Wiring: Once the original lamp is out, carefully pull off the electrical connector directly from the lamp.
- Connect New Lamp: Connect the wiring harness from your vehicle to the new S5-#124 LED Welcome Light Projector. Ensure the connection is secure.
- Insert New Lamp: Carefully insert the new LED Welcome Light Projector into the original lamp slot until it clicks into place. Ensure it is flush with the door panel.
- Test Functionality: Open and close the car door to verify that the light projects correctly when the door is open and turns off when closed.

4. Operating Instructions
The LED Car Door Welcome Light Projector operates automatically. When a car door is opened, the light will illuminate, projecting the chosen logo onto the ground. When the door is closed, the light will automatically turn off. No manual operation is required after installation.
5. Maintenance
The S5-#124 LED Car Door Welcome Light Projector requires minimal maintenance.
- Cleaning: If the lens or housing becomes dirty, gently wipe it with a soft, damp cloth. Avoid using abrasive cleaners or solvents, as these can damage the lens or plastic components.
- Inspection: Periodically check the lights for any signs of damage or loose connections.
- Water Exposure: While the product is IP68 waterproof, avoid directing high-pressure water jets directly at the light during car washes.
6. Troubleshooting
If you encounter any issues with your LED Car Door Welcome Light Projector, refer to the following common problems and solutions:
- Light Does Not Turn On:
- Check the electrical connection to ensure it is secure and properly seated.
- Verify that the car door is fully open.
- Ensure your vehicle's door light circuit is functioning correctly (e.g., check if the original light worked).
- Inspect the light for any visible damage.
- Projection is Dim or Blurry:
- Clean the projector lens with a soft, lint-free cloth. Dust or debris on the lens can affect projection clarity.
- Ensure the light is fully seated and oriented correctly in its slot.
- Light Flickers:
- Check the electrical connection for any looseness.
- Ensure the voltage supply from the car is stable (this is usually not an issue with standard car electrical systems).
If the problem persists after trying these steps, please consult a qualified automotive technician.
7. User Tips
- Fitment: Some users have noted a tight fit during installation. Ensure the light is aligned correctly before applying gentle, even pressure to snap it into place. Do not force the light if it doesn't fit, as this may cause damage.
- Packaging Check: Upon receiving your product, inspect the packaging for any damage and ensure all components are present before beginning installation.
- Pre-Installation Test: Before fully securing the light into the door panel, connect it to the car's wiring and briefly test its function to confirm it works.
8. Frequently Asked Questions (FAQ)
- Q: Do I need to drill holes in my car door?
- A: No, this product is designed for nondestructive installation and directly replaces your car's original door lights. No drilling is required.
- Q: Is this light compatible with my car?
- A: Please refer to the 'Applicable Models' section (2.2) to confirm compatibility with your specific Skoda model and year.
- Q: How long do the LED lights last?
- A: LED lights are known for their long lifespan, typically tens of thousands of hours, ensuring durable performance.
9. Warranty and Support
For any warranty claims, technical support, or further assistance, please contact your retailer or the manufacturer directly. Please have your purchase details and product model number (S5-#124) ready when contacting support.
A detailed user manual in PDF format may also be available for download from the seller's product page or by contacting customer support.