1. Introduction
The Hantek DSO4072S is a versatile 2-channel digital oscilloscope integrated with a 1-channel arbitrary/function waveform generator. Designed for convenient simultaneous operation, it features a 70MHz bandwidth, 1GSa/s real-time sample rate, and a 25MHz arbitrary waveform generator with 12-bit resolution and 200MHz DDS. The device is equipped with a large 7-inch 64K color LCD display with an 800x480 resolution, providing clear and realistic waveform visualization. This manual provides essential information for the safe and effective use of your Hantek DSO4072S.
2. Safety Information
Please read and understand all safety instructions before operating the device. Failure to follow these instructions may result in injury or damage to the instrument.
- **Power Supply:** Use only the power adapter supplied with the instrument. Ensure the power source matches the voltage requirements specified on the device.
- **Grounding:** Always ensure the instrument is properly grounded to prevent electric shock.
- **Environment:** Operate the device in a dry, well-ventilated area. Avoid exposure to moisture, extreme temperatures, or corrosive gases.
- **Maintenance:** Do not attempt to open or repair the instrument yourself. Refer all servicing to qualified personnel. Hazardous voltage is present inside.
- **Probes:** Use only probes rated for the voltage and current levels you intend to measure. Ensure probes are correctly connected and calibrated.
3. Package Contents
Upon unpacking your Hantek DSO4072S, please verify that all items listed below are present and in good condition:
- Hantek DSO4072S Digital Oscilloscope Unit
- Oscilloscope Probes (2 units)
- Power Cord
- USB Cable
- User Manual
- Software CD (for PC connectivity)

4. Product Overview
The Hantek DSO4072S combines the functionalities of a digital oscilloscope and an arbitrary waveform generator in a single, compact unit. Its intuitive interface and dedicated controls for both functions allow for seamless operation.




5. Setup
Follow these steps to set up your Hantek DSO4072S for initial use:
- **Power Connection:** Connect the provided power cord to the instrument's power input on the rear panel and then to a suitable AC power outlet.
- **Probe Connection:** For oscilloscope functions, connect the oscilloscope probes to the CH1 and CH2 BNC inputs on the front panel. Ensure a secure connection.
- **Waveform Generator Output:** For waveform generation, connect your test circuit to the AWG output BNC connector.
- **USB Connection (Optional):** To connect the device to a computer for data transfer or software control, use the provided USB cable to connect the instrument's USB interface (Figure 4.3) to your PC. Install the necessary drivers and software from the included CD.
- **Initial Power On:** Press the power button to turn on the device. The display will light up.
- **Language Setting:** If needed, navigate to the system settings (as shown in Figure 4.4) to select your preferred language, such as English.
6. Operating Instructions
The Hantek DSO4072S features separate control sections for the oscilloscope and waveform generator, allowing for independent or simultaneous operation.
6.1 Oscilloscope Operation
- **Vertical Controls:** Use the VOLTS/DIV knobs for CH1 and CH2 to adjust the vertical scale (voltage per division). The POSITION knobs adjust the vertical position of the waveforms.
- **Horizontal Controls:** Use the SEC/DIV knob to adjust the horizontal time base (time per division). The HORIZ POSITION knob adjusts the horizontal position.
- **Trigger System:** The TRIGGER section allows you to stabilize repetitive waveforms. Adjust the LEVEL knob to set the trigger threshold. Select trigger type (Edge, Video, Pulse, Slope, Over time, Alternative) using the dedicated buttons.
- **Measurement Functions:** The oscilloscope supports over 20 types of automatic measurements. Access these through the menu system.
- **Acquisition Modes:** Choose between Normal, Peak Detect, and Average acquisition modes depending on your measurement needs.
6.2 Waveform Generator Operation
- **Generator Controls:** The GENERATOR section has dedicated buttons and knobs. Press 'GEN ON' to activate the generator.
- **Waveform Selection:** Select the desired waveform type (arbitrary wave, square wave, sine wave, triangle wave, trapezoidal wave, pulse wave, DC) from the menu.
- **Parameter Adjustment:** Adjust frequency, amplitude, and offset using the corresponding controls or menu options.
6.3 Data Storage and Connectivity
- **USB Host:** The integrated USB Host port allows for direct storage of waveform data to a USB disk.
- **SD Card Support:** The device supports SD card storage for saving and recalling settings and waveforms.
- **PC Software:** Use the provided PC software to control the oscilloscope, analyze data, and perform firmware updates via the USB interface.
7. Specifications
Detailed technical specifications for the Hantek DSO4072S are provided below:
| Category | Parameter | DSO4072S |
|---|---|---|
| Oscilloscope | Bandwidth | 70MHz |
| Digital Channels | 2 | |
| Real Time Sampling Rate | 1GSa/s | |
| Equivalent Sample Rate | 25GSa/s | |
| Record Length | 40K | |
| Max Waveform Capture Rate | 30,000wfm/s | |
| SEC/DIV Range | 4ns/div to 40s/div | |
| Vertical Resolution | 8-bit | |
| Inputs Impedance | 1MΩ±2% ‖20pF±3pF | |
| Maximum Input Voltage | CAT I and CAT II: 300VRMS (10×), CAT III: 150VRMS(1×) | |
| Waveform Generator | Frequency | 25MHz |
| Resolution | 12 bits | |
| DDS Frequency | 200MHz | |
| Waveform Types | Arbitrary, Square, Sine, Triangle, Trapezoidal, Pulse, DC | |
| Display | Type | 7 inch 64K color LCD |
| Resolution | 800x480 Pixels | |
| Display Size | 7 Inches & Above | |
| General | Certification | CE |
| DIY Supplies | Electrical | |
| Origin | Mainland China |
8. Maintenance
Proper maintenance ensures the longevity and accuracy of your Hantek DSO4072S.
- **Cleaning:** Regularly clean the exterior of the instrument with a soft, dry cloth. For stubborn dirt, use a cloth lightly dampened with water and mild detergent. Do not use abrasive cleaners or solvents.
- **Screen Care:** Use a soft, lint-free cloth to clean the LCD screen. Avoid pressing hard on the screen.
- **Storage:** When not in use, store the oscilloscope in a cool, dry place, away from direct sunlight and extreme temperatures. Keep it covered to prevent dust accumulation.
- **Probe Care:** Inspect probes regularly for damage to cables or connectors. Replace damaged probes immediately.
9. Troubleshooting
If you encounter issues with your Hantek DSO4072S, try the following basic troubleshooting steps:
- **No Power:** Ensure the power cord is securely connected to both the instrument and the power outlet. Verify the power outlet is functional.
- **No Waveform Display:** Check that probes are correctly connected to the input channels and the test circuit. Verify the input signal is within the instrument's measurement range. Adjust vertical (VOLTS/DIV) and horizontal (SEC/DIV) scales, and trigger settings.
- **Unstable Waveform:** Adjust the trigger level and trigger type. Ensure the trigger source is correctly selected.
- **Incorrect Measurements:** Perform a self-calibration if available in the system menu. Check probe attenuation settings (1X/10X) and ensure they match the instrument's settings.
- **USB/SD Card Issues:** Ensure the USB disk or SD card is properly inserted and formatted. Try a different USB device or SD card.
If problems persist, contact customer support for further assistance.
10. User Tips
Here are some tips to enhance your experience with the Hantek DSO4072S:
- **Probe Compensation:** Always perform probe compensation when using new probes or if you suspect measurement inaccuracies. This typically involves connecting the probe to a dedicated compensation signal on the oscilloscope and adjusting the probe for a flat-top square wave.
- **Grounding Practices:** For accurate measurements and safety, ensure that the ground clip of your oscilloscope probe is connected to the ground of the circuit under test. Avoid creating ground loops.
- **Firmware Updates:** Periodically check the Hantek official website for firmware updates. Updates can improve performance, add features, and fix bugs.
- **Utilize the Waveform Generator:** The integrated arbitrary waveform generator is excellent for testing circuits. Experiment with different waveform types and frequencies to thoroughly test your designs.
- **Save Settings:** If you frequently use specific settings for certain tests, save them to a USB drive or SD card for quick recall.
11. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact the seller directly. Keep your proof of purchase for warranty claims.