1. Introduction
Thank you for purchasing the M4 Pocket balance charger. Please read this manual carefully before use to ensure proper operation and safety.
For further information, news, and firmware updates, please visit the official ToolkitRC website: www.toolkitrc.com/M4Pocket.
2. Safety Instructions
- The M4 Pocket accepts an input voltage of DC 7.0-25.0V. Ensure the charger is only connected to a suitable AC power outlet.
- Do not use this product in hot, humid, flammable, or explosive environments.
- Please do not use this charger without supervision. Never leave charging batteries unattended.
- When not using this product, please unplug the input power.
- When using the charging function, please set a current that matches the battery. Do not set an excessive current for charging to avoid damage to the battery. Check the guidelines of your battery's manufacturer for correct charging instructions.
⚠ WARNING: This product can expose you to chemicals including phthalates (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
3. Product Overview
3.1. Key Features
- Charge and balance management for LiPo, LiHV, LiFe & Lion 1-4S batteries.
- Voltage input: DC 7.0-25.0V.
- Charging current: Maximum 5.0A @MAX 80W.
- User-defined Lithium battery cut-off voltage (TVC function).
- Battery voltage can be manually calibrated.
- Charging accuracy: <0.005V.
- Balance current: 400mA.
- 1.54 inch, IPS full viewing angle display.
- High resolution 240*240 pixels.
3.2. M4 Pocket Layout

This diagram shows the front of the M4 Pocket, highlighting the display screen, Voltage/Current key, heat dissipation vents, and XT60/XT30 output ports.

This diagram illustrates the back of the M4 Pocket, pointing out the balance port and the XT60/USB-C input port.
3.3. Product Overview Video
Video 1: ToolkitRC M4Pocket Unboxing and Initial Connection
This video demonstrates the unboxing of the M4 Pocket charger and its initial connection to a battery for charging.
4. Setup Guide
- Connect the M4 Pocket to a suitable DC 7.0-25.0V power outlet.
- The display will show the boot logo for 2 seconds.
- After booting up, the screen enters the main interface.

The main display of the M4 Pocket showing charging parameters and battery status.
- Short press the [Voltage/Current] key to unlock the system and start adjusting parameters.
- Long press the [Voltage/Current] key to set the charging cut-off voltage.
- Short press the [Voltage/Current] key to select the charging current.
- When the output main port and the balance port voltage match, the M4 Pocket will automatically start charging.
Tip: Every time you turn on the charger, you need to press the button once to unlock the system. This is a safety feature designed to prevent incorrect selection of battery type and current.
5. Operating Instructions
5.1. Charging Settings
After the power is turned on and the charger unlocked, the screen will display the charging interface.
5.1.1. Battery Type Setting
Long press the [Voltage/Current] key to select the battery cut-off voltage (battery type).
| Cut-off Voltage | Battery Type |
|---|---|
| 4.20V | Lipo |
| 4.35V | LiHv |
| 3.85V | Lipo-Storage |
| 3.60V | LiFe |
Important: Ensure the correct battery type has been selected prior to charging. An incorrect choice may damage the battery and/or become a fire hazard. Please use caution. Do not use this product to charge non-compatible battery chemistries.
Nomenclature:
- Lipo: Often referred to as a lithium polymer battery, with a nominal voltage of 3.70V and 4.20V when fully charged.
- LiHV: Often referred to as a high-voltage lithium battery, with a nominal voltage of 3.85V and 4.35V when fully charged.
- LiFe: Often referred to as an iron-lithium battery, with a nominal voltage of 3.30V and 3.60V when fully charged.
- Lion: Often called a lithium-ion battery, with a nominal voltage of 3.60V and 4.10V when fully charged.
5.1.2. Current Setting
Short press the [Voltage/Current] key to select the charging current. The current can be selected from 4 values: 1.0A, 2.0A, 3.0A, 5.0A.
Tip: When selecting the current, it is recommended to use a charging rate of 1C-2C. For example, for a 1000mAh battery, use 1.0A-2.0A for charging. This effectively improves the cycle life of the battery. Always check the battery manufacturer's guidelines and charging instructions before charging.
5.2. Start Charging
After setting the battery voltage and current, connect the battery. Once the charger detects that the voltage between the main port and the balance port matches, it will automatically start charging.

The display shows real-time charging information, including voltage, current, and cell balance status. The new model has 5 gears for current adjustment.
Display Content Description:
- 000:18: Charging time.
- 20.5V: Input voltage.
- 35°C: Charger temperature.
- 4.20v: The selected cell type cutoff voltage.
- 4.35v 3.85v 3.60v: Other cell cutoff voltages (not selected).
- 16.0V: Current battery voltage.
- 5.00A: Current charging current.
- C: Current limit sign.
- P: Power current limit.
- T: Temperature limit.
- F: The battery or one of the cells is full.
- 888mAh: Accumulated capacity that has been charged.
- 4.000V: The first cell voltage, this cell is not balancing.
- 4.001V: The second cell voltage, this cell is slowly balancing.
- 4.002V: The third cell voltage, this cell is slowly balancing.
- 4.005V: The fourth cell voltage, this cell is quickly balancing.
Tip: When charging a 1S battery, the battery voltage needs to be provided to the balance port at the same time, so that the charger can recognize and start charging.
6. Maintenance
- Keep the charger clean and free from dust and debris. Use a soft, dry cloth for cleaning.
- Store the charger in a cool, dry place away from direct sunlight and extreme temperatures.
- Regularly inspect cables and connectors for any signs of wear or damage. Replace damaged components immediately.
- Ensure proper ventilation around the charger during operation to prevent overheating.
7. Troubleshooting
7.1. Terminal Voltage Setting and Manual Calibration
If cell voltage readings appear to be incorrect, you can manually calibrate the charger. Before connecting to the power supply, press and hold the [Voltage/Current] key to enter the calibration mode.
Calibration Mode Display:
Terminal voltage:
4.20v 4.35v 3.85v 3.60v
Calibration voltage:
IN: 12.00v 4 4.200v
OT: 16.00v 3 4.200v
0 2 4.200v
DEFAULT 1 4.200v- Terminal voltage: This refers to the terminal voltage after the battery is fully charged. It is accurate to +/- 10mV.
- Calibration voltage: If the cell voltage readings appear to be incorrect, use a high-quality voltage meter to measure the actual voltage, then set this value to be the same as the meter.
- DEFAULT: Select this option to restore the charger to factory default settings.
7.2. General Troubleshooting Tips
- Charger not powering on: Ensure the input power supply is correctly connected and within the specified voltage range (DC 7.0-25.0V). Check the power cable for damage.
- Charging not starting: Verify that the battery type and current settings are correct. Ensure the main output port and balance port voltages match the connected battery. Press the [Voltage/Current] key to unlock the system after power-on.
- Overheating: Ensure the heat dissipation vents are not blocked. Reduce the charging current if the charger consistently overheats.
- Incorrect voltage readings: Perform a manual calibration as described in section 7.1.
8. User Tips
Based on user feedback and common practices, here are some tips for optimal use:
- Always double-check your battery type and cell count before starting a charge cycle to prevent damage.
- For longer battery life, consider charging at a 1C rate or lower when time permits.
- Utilize the storage mode (Lipo-Storage) for batteries that will not be used for an extended period to maintain their health.
- Keep the firmware updated to benefit from the latest features and improvements. Refer to the ToolkitRC website for updates.
9. Specifications
| Category | Parameter | Value |
|---|---|---|
| Input | XT60 Input | 7.0-25.0V MAX 5A |
| USB-C Input | 5.0-20.0V@QC,PD,AFC,FCP | |
| Charge | Battery Type | LiPo, LiHV, LiFe, LipoStorage 1-4S |
| Charging Power | 1.0-5.0A @ 80W | |
| Balance Current | MAX 400mA @4.20V | |
| Charging Accuracy | <0.005V @4.20V | |
| USB-C Output | Output | 1.0A@5.0V |
| Display | LCD Type | IPS 1.54" 240*240 Pixels |
| Size | 80*40*30mm | |
| Product | Weight | 75g |
| Individual Packing Size | 82*42*32 mm | |
| Individual Packing | Weight | 85g |
10. Warranty and Support
For warranty information, technical support, and service inquiries, please refer to the official ToolkitRC website or contact your local distributor.
An electronic version of this user manual is available in PDF format: Download User Manual (PDF).