1. Safety Information
The following safety precautions shall always be observed during operation, service, and repair of this equipment.
- This equipment shall be serviced by qualified technicians only.
- Do not modify the radio for any reason.
- Use only supplied or approved batteries and chargers.
- Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.
- Turn off your radio prior to entering any area with explosive and flammable materials.
- Do not charge your battery in a location with explosive and flammable materials.
- To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any area where posted notices instruct you to do so.
- Turn off your radio before boarding an aircraft. Any use of a radio must be in accordance with airline regulations or crew instructions.
- Turn off your radio before entering a blasting area.
- For vehicles with an air bag, do not place a radio in the area over an air bag or in the air bag deployment area.
- Do not expose the radio to direct sunlight over a long time, nor place it close to heating source.
- When transmitting with a portable radio, hold the radio in a vertical position with the microphone 3 to 4 centimeters away from your lips. Keep antenna at least 2.5 centimeters away from your body when transmitting.
WARNING: If you wear a radio on your body, ensure the radio and its antenna are at least 2.5 centimeters away from your body when transmitting.
2. Features and Functions
The Baofeng UV S22 Pro V2 is an IP68 dust and waterproof two-way radio, designed for high performance and reliability in various environments. It features a new upgrade design with colorful options and two-tone frequency buttons.
Video: Baofeng Factory Production Overview
Key Features:
- IP68 Waterproof and Dustproof: Withstands immersion in 2 meters of water for 30 minutes.
- High Power Output: Selectable 10W/5W/1W for versatile communication needs.
- Extended Range: Up to 50 KM maximum range, with coverage of 5-10KM in cities, 10-25KM in suburbs, and 15-50KM in plains. Can penetrate 1-70 floors in buildings.
- Dual Band Operation: VHF (136-174MHz) and UHF (400-520MHz).
- Memory Channels: Up to 128 memory channels.
- Cross Band Reception/Transmission: Allows communication across different frequency bands.
- Display Options: Various display modes for channel number, frequency, and channel name.
- CTCSS & DCS: 50 CTCSS tones and 210 DCS codes for enhanced privacy and selective calling.
- VOX Function: Voice Operated Transmission for hands-free communication.
- DTMF Emergency Alarm: For critical situations.
- SOS Emergency Function: Sound and light alarm for emergencies.
- FM Radio Receiver: (87.5-108MHz).
- Built-in LED Flashlight: High brightness for working in the dark.
- Power Save: For extended battery life.
- TOT (Time out timer): Prevents accidental continuous transmission.
- Keypad Lock: Prevents accidental changes to settings.
- USB (Type-C) Charging: Convenient charging.
- Durable Design: High-density shell, anti-extrusion, and drop resistance.

Figure 2.1: Product Features and Included Accessories

Figure 2.2: Strong Power and Coverage Capabilities

Figure 2.3: IP68 Waterproof Protection

Figure 2.4: High Brightness LED Flashlight for Dark Environments

Figure 2.5: SOS Alarm Prompt for Safety

Figure 2.6: UV Dual Band and FM Radio Support

Figure 2.7: Powerful and Versatile Features

Figure 2.8: Fully Upgraded Sound with Large-Caliber Vibration Unit

Figure 2.9: 771 Aerial for Longer Distance Communication

Figure 2.10: Applicable to All Kinds of Work
3. Setup
3.1. Unpacking and Checking Equipment
Carefully unpack the transceiver. Identify the items listed below. If any items are missing or damaged, contact your dealer immediately.
- Portable radio unit
- Antenna
- Li-ion battery pack
- Li-ion charger
- Belt clip
- Lanyard
- User's manual
- Type-C Charging Cable

Figure 3.1: Standard Package Contents
3.2. Installation of Accessories
3.2.1. Installing the Antenna
Install the antenna by screwing it clockwise onto the connector at the top of the radio until it stops. Hold the antenna by its base, not the top, when turning.
Note:
- If using an external antenna, ensure the SWR is about 1.5:1 or less to prevent damage to the transceiver's final transistors.
- Never transmit without an antenna.
3.2.2. Installing the Belt Clip
If needed, attach the belt clip to the rear of the battery compartment cover using the provided screws.
Note:
- Do not use any glue to fix the screw on the belt clip, as solvents may damage the battery casing.
3.2.3. Micro-Headset Installation
Plug the external micro-headset connector into the 'SP. & MIC' jack on the side of the transceiver.
3.2.4. Battery Installation
When attaching the battery, ensure it is parallel and in good contact with the aluminum chassis. Align the battery with the guide rails and slide it upwards until a "click" is heard, indicating it is locked.
To remove the battery, first turn off the radio. Slide the battery latch at the bottom of the radio's body in the direction indicated by the arrow. Slide the battery down for 1 to 2 centimeters, then remove it.
4. Battery Information and Charging
4.1. Initial Use
New batteries are shipped uncharged. Charge a new battery for 5 hours before initial use. Maximum battery capacity and performance are achieved after three full charge/discharge cycles. Recharge the battery when power runs low.
WARNING:
- To reduce the risk of injury, charge only with the manufacturer-specified charger. Other batteries may burst, causing injury and property damage.
- Do not dispose of batteries in fire.
- Dispose of batteries according to local regulations (e.g., recycling). Do not dispose as household waste.
- Never attempt to disassemble the battery.
4.2. Battery Charging
Use only the specified charger. The charger's LED indicates the charging progress:
| Charging Status | LED Indication |
|---|---|
| Standby (no-load) | Red LED flashes, Green LED glows |
| Charging | Red LED solidly glows |
| Fully Charged | Green LED solidly glows |
| Error | Red LED flashes, Green LED glows |

Figure 4.1: Easy Battery Charging with LED Indicators
4.3. Battery Tips
- When charging, keep the battery temperature between 5°C and 40°C. Extreme temperatures can cause leakage or damage.
- If charging a battery attached to the radio, turn the radio off for a full charge.
- Do not cut off the power supply or remove the battery during charging.
- Never charge a wet battery; dry it with a soft cloth first.
- Batteries wear out over time. Replace the battery when operating time significantly shortens.
4.4. Battery Storage
- Fully charge the battery before long-term storage to prevent over-discharge.
- Recharge Li-Ion batteries after several months (e.g., 6 months) of storage to prevent capacity reduction.
- Store the battery in a cool, dry place at room temperature to reduce self-discharge.
5. Operation
5.1. Radio Overview and Key Functions

Figure 5.1: Function Key Analysis
5.1.1. Command/Key Definition
- Power On: Rotate the PWR/VOL Switch clockwise. You will hear a "Beep" and the radio will report the current channel. Adjust volume by rotating the switch.
- [SOS] Emergency Alarm: Long press [SOS] to activate the alarm function (green/red lights and hand lamp flash). Press again to deactivate.
- [PTT] (Push-to-Talk): Press and hold to transmit, then talk into the microphone. Release to receive.
- SK-SIDE KEY1/[F]: Press to activate/deactivate FM Radio.
- SK-SIDE KEY2/[M]: Press to turn on/off the flashlight. Long press to monitor the signal.
- [MENU] Key: Press to enter the menu and confirm settings. Press and hold [MENU] during power-on to switch between frequency and channel mode.
- [▲]/[▼] Keys: Press to adjust frequency/channel up or down. Hold for fast adjustment.
- [EXIT/AB] Key: Press to cancel/clear or exit. In standby, switch between Channel A and B. In FM radio mode, switch radio bands (65-75MHz/76-108MHz).
5.2. LCD Display Icons
The LCD displays icons indicating various operations and features:
| Icon | Description |
|---|---|
| + | Frequency Shift + |
| - | Frequency Shift - |
| +- | Frequency offset direction for accessing repeaters. |
| S | Dual Watch/Dual Reception functions activated. |
| VOX | Function 'VOX' enabled. |
| R | Reverse function activated. |
| N | Wide Band selected. |
| ... | Battery Level indicator |
| Keypad lock function activated. | |
| L | Low transmit power. |
| ▲▼ | Operation frequency. |
| Yull | Signal Strength Level. |
| 88 | Operating channel. |
| 75/25 | Operating frequency. |
| CT | 'CTCSS' activated. |
| DCS | 'DCS' activated. |
5.3. Basic Operation
5.3.1. Radio On-Off/Volume Control
Ensure the antenna and battery are correctly installed and charged. Rotate the PWR/VOL knob clockwise to turn the radio on and adjust the volume. Rotate fully counter-clockwise to turn off.
5.3.2. Transmit and Receive
Select the desired channel or enter the frequency. Press and hold the PTT button to transmit, then speak into the microphone. Release PTT to receive.
- When PTT is pressed, 'L' on the LCD indicates low power.
- When PTT is pressed, 'M' on the LCD indicates mid power.
- When PTT is pressed, 'H' on the LCD indicates high power.
- Press [PTT] then [SOS] to transmit 1750Hz tone.
- Press [PTT] then DTMF Numbers to transmit DTMF.
5.3.3. VOX (Voice Operated Transmission)
This function allows transmission without pressing PTT. The radio activates transmission when it detects your voice and terminates when you stop speaking. Adjust the VOX Gain level (1-10, 10 being most sensitive) in the menu (Function 4) for smooth transmission.
5.3.4. AUTOLK (Keypad Locked Automatically)
The transceiver offers auto lock and manual lock. To set auto lock, in standby, press [MENU] + number key 24, then select ON/OFF for keyboard lock. When ON, the keypad locks after 2 seconds of inactivity.
5.3.5. VFO/Channel Mode
Turn off the radio, then press [MENU] and rotate the sound knob to turn on the radio. The screen will show either frequency (VFO mode) or channel number (Channel mode). Use [▲]/[▼] keys to select frequency/channel. Hold for fast adjustment.
5.3.6. TDR (Dual Watch/Dual Reception)
This feature allows monitoring two frequencies (A and B). The transceiver periodically checks for signals on both. If a signal is received, it stays on that frequency until the signal disappears. Activate/deactivate TDR by pressing [MENU] + keyboard [7TDR] and selecting OFF or ON.
5.3.7. MEM-CH (Stored In Memory Channel)
The transceiver has 128 memory channels (000 to 127). To store a frequency and its parameters, input them in frequency mode or standby. To select a stored channel, press [MENU] + [Number key 27] and choose the desired channel order.
5.3.8. DEL-CH (Delete Channel)
To delete a channel, in standby, press [MENU] + [Number key 28], then select the channel to delete. Confirm with [MENU].
5.3.9. CTCSS/DCS Scanning
Before scanning, ensure the radio is in VFO mode and Dual Standby is off. Go to MENU 11, press [MENU], then [*/SCAN]. While scanning, press PTT on another radio to automatically find its CTCSS/DCS. Press [MENU] to store.
Note:
- Using CTCSS/DCS does not guarantee complete communication confidentiality.
5.3.10. Repeater Tail Tone
Repeaters use a courtesy tone. MENU 35 and MENU 36 should be OFF. MENU 37 (repeater tail tone delay) can be set from 1-10, with 5 being a good default.
5.3.11. CTCSS/DCS Tables
These tables list the available CTCSS tones and DCS codes for selective calling.
| NO | Tone (Hz) | NO | Tone (Hz) | NO | Tone (Hz) | NO | Tone (Hz) | NO | Tone (Hz) |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 67.0 | 11 | 94.8 | 21 | 131.8 | 31 | 171.3 | 41 | 203.5 |
| 2 | 69.3 | 12 | 97.4 | 22 | 136.5 | 32 | 173.8 | 42 | 206.5 |
| 3 | 71.9 | 13 | 100.0 | 23 | 141.3 | 33 | 177.3 | 43 | 210.7 |
| 4 | 74.4 | 14 | 103.5 | 24 | 146.2 | 34 | 179.9 | 44 | 218.1 |
| 5 | 77.0 | 15 | 107.2 | 25 | 151.4 | 35 | 183.5 | 45 | 225.7 |
| 6 | 79.7 | 16 | 110.9 | 26 | 156.7 | 36 | 186.2 | 46 | 229.1 |
| 7 | 82.5 | 17 | 114.8 | 27 | 159.8 | 37 | 189.9 | 47 | 233.6 |
| 8 | 85.4 | 18 | 118.8 | 28 | 162.2 | 38 | 192.8 | 48 | 241.8 |
| 9 | 88.5 | 19 | 123.0 | 29 | 165.5 | 39 | 196.6 | 49 | 250.3 |
| 10 | 91.5 | 20 | 127.3 | 30 | 167.9 | 40 | 199.5 | 50 | 254.1 |
DCS Table:
| No | Code | NO | Code | NO | Code | NO | Code | NO | Code |
|---|---|---|---|---|---|---|---|---|---|
| 1 | D023N | 22 | D131N | 43 | D251N | 64 | D371N | 85 | D532N |
| 2 | D025N | 23 | D132N | 44 | D252N | 65 | D411N | 86 | D546N |
| 3 | D026N | 24 | D134N | 45 | D255N | 66 | D412N | 87 | D565N |
5.4. Shortcut Menu Operation
To access and navigate the shortcut menu:
- Press the [MENU] key, then use [▲] or [▼] to select the desired menu item.
- Press the [MENU] key again to enter the parameter setting for the selected item.
- Use [▲] or [▼] to select the desired parameter value.
- Press the [MENU] key to confirm and save. Press [EXIT] to cancel or clear the input.
Note:
- In channel mode, certain menu settings (CTCSS, DCS, W/N, PTT-ID, BCL, SCAN ADD TO, S-CODE, CHANNEL NAME) are invalid. Only H/L power can be changed by pressing the '#' key.
5.5. Set Menu Description
The following table details the available menu options and their settings:
| Menu | Function/Description | Available settings |
|---|---|---|
| 0 | SQL (Squelch level) | 0-9 |
| 1 | STEP (Frequency step) | 2.5/5/6.25/10/12.5/20/25/50kHz |
| 2 | TXP (Transmit power) | HIGH/MID/LOW |
| 3 | SAVE (Battery save, 1:1/1:2/1:3/1:4) | OFF/1/2/3/4 |
| 4 | VOX (Voice operated transmission) | OFF/1-10 |
| 5 | W/N (Wideband/narrowband) | WIDE/NARR |
| 6 | ABR (Display illumination) | OFF/1/2/3/4/5s |
| 7 | TDR (Dual watch/dual reception) | OFF/ON |
| 8 | BEEP (Keypad beep) | OFF/ON |
| 9 | TOT (Transmission timer) | 15/30/45/60.../585/600seconds |
| 10 | R-DCS (Reception digital coded squelch) | OFF/D023N...D754I |
| 11 | R-CTS (Reception Continuous Tone Coded Squelch) | 67.0Hz...254.1Hz |
| 12 | T-DCS (Transmission digital coded squelch) | OFF/D023N...D754I |
| 13 | T-CTS (Transmission Continuous Tone Coded Squelch) | 67.0Hz...254.1Hz |
| 14 | VOICE (Voice prompt) | OFF/ON |
| 15 | ANI (Automatic number identification of the radio, only can be set by PC software.) | |
| 16 | DTMFST (The DTMF tone of transmitting code.) | OFF/DT-ST/ANI-ST/DT+ANI |
| 17 | S-CODE (Signal code, only could be set by PC software.) | 1,......, 15 groups |
| 18 | SC-REV (Scan resume method) | TO/CO/SE |
| 19 | PTT-ID (press or release the PTT button to transmit the signal code) | OFF/BOT/EOT/BOTH |
| 20 | PTT-LT (delay the signal code sending) | 0,......,30ms |
| 21 | MDF-A (under channel mode, A channel displays. Note:name display only can be set by PC software.) | FREQ/CH/NAME |
| 22 | MDF-B (under channel mode, B channel displays. Note:name display only can be set by PC software.) | FREQ/CH/NAME |
| 23 | BCL (busy channel lockout) | OFF/ON |
| 24 | AUTOLK (keypad locked automatically) | OFF/ON |
| 25 | SFT-D (direction of frequency shift) | OFF/+/- |
| 26 | OFFSET (frequency shift) | 00.000...69.990 |
| 27 | MEMCH (stored in memory channels) | 000,...127 |
| 28 | DELCH (delete the memory channels) | 000,...127 |
| 29 | WT-LED (illumination display color of standby) | OFF/BLUE/ORANGE/PURPLE |
| 30 | RX-LED (illumination display color of reception) | OFF/BLUE/ORANGE/PURPLE |
| 31 | TX-LED (illumination display color of transmitting) | OFF/BLUE/ORANGE/PURPLE |
| 32 | AL-MOD (alarm mode) | SITE/TONE/CODE |
| 33 | BAND (band selection) | VHF/UHF |
| 34 | TX-AB (transmitting selection while in dual watch/ reception) | OFF/A/B |
| 35 | STE (Tail Tone Elimination) | OFF/ON |
| 36 | RP_STE (Tail tone elimination in communication through repeater) | OFF/1,2,3...10 |
| 37 | RPT_RL (Delay the tail tone of repeater) | OFF/1,2,3...10 |
| 38 | PONMGS (Boot display) | FULL/MGS |
| 39 | ROGER (tone end of transmission) | ON/OFF |
| 40 | A/B-BP (Tone end of reception) | OFF/A/B |
| 41 | RESET (Restore to default setting) | VFO/ALL |
5.6. Reset (Restore To Default Setting)
The transceiver has a menu to reset VFO and ALL messages. RESET VFO returns all parameters to factory default. RESET ALL returns all transceivers and channel parameters to factory default.
In standby, press [MENU] + [Number Key 40], then the screen will display "RESET". Press [MENU] to enter, use [UP] or [DOWN] to select VFO or ALL. Press [MENU] to confirm, then [EXIT] to return to standby.
5.7. Copying
To copy Radio A to Radio B:
- Connect the two radios with a special data cable.
- Turn on Radio B.
- Press [MONI] while turning on Radio A. The screen will show "COPYING". Once finished, Radio B will power off and then on automatically.
Repeat steps 2 and 3 to clone more radios. If cloning fails, ensure both radios are off and correctly connected with the clone cable.
6. Troubleshooting
| Problem | Possible Cause / Solution |
|---|---|
| The radio does not start. | The battery is low; replace with a charged battery or charge the current one. The battery may not be installed correctly; remove and reattach it. |
| The battery runs down quickly. | The battery life may be at its end; replace the battery. Ensure the battery is fully charged. |
| The receiving indicator LED lights but no sound from the speaker. | Volume setting is too low. Ensure CTCSS or DCS undertones match those programmed in other group members' transceivers. |
| When transmitting, other group members do not receive the communication. | Ensure CTCSS or DCS codes match. You or your partner may be too far apart or in an area with poor radio signal propagation (e.g., inside a tunnel, underground car park, mountainous area, large metal structures). |
| In "standby" mode, the transceiver transmits without pressing the "PTT". | Check the VOX level adjustment function; it may be set too sensitive. |
| Receiving communications from other user groups while communicating with your group. | Change frequency or channel. Change the CTCSS or DCS undertones in your group. |
If these checks do not resolve the issue, contact your distributor, dealer, or service center.
7. Technical Specifications
7.1. General
| Parameter | Value |
|---|---|
| Product Name | UV-S22pro |
| Call Distance | 2-50KM |
| Power | VHF/UHF High Power (5W-10W) |
| Battery | Large Capacity Lithium Battery (8800mAh, 7.4V/1800) |
| Frequency Range | VHF: 136-174MHz (Rx/Tx), UHF: 400-520MHz (Rx/Tx) |
| Commercial FM Radio | 65MHz-108MHz (Reception only) |
| Memory Channels | Up to 128 channels |
| Frequency Stability | 2.5ppm |
| Frequency Step | 2.5kHz/5kHz/6.25kHz/10kHz/12.5kHz/20kHz/25kHz |
| Antenna Impedance | 50 Ω |
| Operating Temperature | -10°C to +45°C |
| Consumption in Reception | 8000mA |
| Consumption in Transmission | ≤1.4A |
| Mode of Operation | Simplex or semi-duplex |
| Duty Cycle | 03/03/54 min. (Rx / Tx / Standby) |
| Dimensions | 132*56*35mm (185mm x 115mm x 102mm) |
| Weight | 220g (490g approximate) |
| Material | Plastic |
| Waterproof / Water-Resistant | IP68 |
| Battery Included | Yes |
| Is_Display | Yes |

Figure 7.1: Product Parameter Configuration
7.2. Transmitter
| Parameter | Value |
|---|---|
| RF Power | 15W |
| Type of Modulation | FM |
| Emission Class | 16K0F3E/11K0F3E (W/N) |
| Maximum Deviation | ≤±5 kHz/≤±2.5 kHz (W/N) |
| Spurious Emissions | <-60 dB |
7.3. Receiver
| Parameter | Value |
|---|---|
| Receiver Sensitivity | 0.2 u V (at 12 dB SINAD) |
| Intermodulation | 60 dB |
| Audio Output | 1W |
| Spurious Radiation | ^65dB |
Note:
- All specifications are subject to change without notice.
8. User Tips
- Earpiece Clarity: Some users have reported issues with earpiece clarity. If you experience blurry or hard-to-hear audio, ensure the earpiece is fully plugged in and consider trying an alternative earpiece for improved sound quality.
- Antenna Performance: For optimal range and signal stability, ensure your antenna is securely attached. The 771 Aerial (22cm) is designed for longer distances and better traversal compared to standard 17cm antennas.
- Battery Life: To prolong battery life, utilize the power save function and ensure the battery is fully charged before extended use.
9. Warranty and Support
9.1. Warranty Certificate
The device is guaranteed for a period of TWO YEARS from the date of sale to the final user. This Warranty Certificate is unique and not transferable. Substitution of product failure or any part thereof shall not involve extension of the guarantee.
The warranty covers the replacement and free replacement of all parts that are defective in materials and components used in manufacturing and/or assembly of the apparatus.
The warranty does not cover any faults caused by accident, improper installation and use, electric shock (e.g., storms), connection to an unspecified power source, reverse polarity, or claims due to deterioration in the external appearance from normal use, nor the amount or condition of the accessories.
Checking the accessories is the responsibility of the purchaser at the time of purchasing the device.
The warranty does not cover rechargeable batteries, as they are considered consumables. Any impairment must be reported within fifteen days from the date of purchase.
9.2. Warranty Exclusions
The warranty is void under the following assumptions:
- Devices that have been manipulated by unauthorized service providers.
- Equipment and accessories where the serial number has been altered, deleted, or is unreadable.
- Use of the product other than as intended.
To make use of the guarantee, provide the dealer or authorized service with the defective device, its accessories, and the following documentation:
- Duly completed and sealed Warranty Certificate.
- Original invoice clearly identifying the device and date of purchase.
- Description of the faults.
The warranty terms do not exclude, modify, or restrict the statutory rights of the buyer by virtue of the laws in force at the time of purchase, but are added to them.
For a more detailed user manual, please refer to the official PDF document: Baofeng UV S22 Pro V2 User Manual (PDF)