RAGEER N70

Contents

RAGEER M.2 SSD Heatsink N70 User Manual

Model: N70

Introduction

The RAGEER M.2 SSD Heatsink N70 is designed to provide efficient passive cooling for your M.2 2280 Solid State Drives. Constructed from high-quality aluminum alloy, this heatsink helps to dissipate heat, prevent thermal throttling, and maintain optimal performance and longevity of your SSD.

RAGEER 2280 SSD Heatsinks in black and gold, 3mm thick, for 2280 SSDs.

Figure 1: RAGEER M.2 SSD Heatsink N70 (Black and Light Gold variants)

Package Contents

Please check the package for the following items:

Diagram showing all included parts: Heatsink, Thermal pad, Screwdriver, two Rubber Rings, and a Screw.

Figure 2: Package Contents

  1. Heatsink (Aluminum Alloy)
  2. Thermal Pad (1mm thick)
  3. Screwdriver
  4. Rubber Rings (x2)
  5. Mounting Screw

Setup and Installation

Follow these steps to install the RAGEER M.2 SSD Heatsink onto your compatible SSD:

Step-by-step installation guide: 1. Peel off plastic film from thermal pad. 2. Place thermal pad on SSD. 3. Secure heatsink with rubber rings.

Figure 3: Installation Steps

  1. Prepare the Thermal Pad: Carefully peel off the protective plastic film from both sides of the thermal pad.
  2. Apply Thermal Pad: Place the thermal pad directly onto the top surface of your M.2 SSD chip(s). Ensure it covers the main heat-generating components.
  3. Position Heatsink: Align the RAGEER M.2 SSD Heatsink over the thermal pad and SSD.
  4. Secure Heatsink: Use the provided rubber rings to firmly secure the heatsink onto the SSD. Ensure the heatsink is snug and makes good contact with the thermal pad.
  5. Install SSD: Install your SSD with the attached heatsink into the M.2 slot on your motherboard or device. Use the provided mounting screw if necessary to secure the SSD in its slot.

Operating Instructions

The RAGEER M.2 SSD Heatsink is a passive cooling solution and requires no active operation. Once installed, it continuously dissipates heat from your M.2 SSD to maintain optimal operating temperatures.

Diagram illustrating cooling effect, showing a temperature reduction of 5°C to 30°C. Main body material is aluminum alloy.

Figure 4: Cooling Effect

  • Cooling Performance: Expect a temperature reduction of approximately 5°C to 30°C, depending on ambient conditions and SSD workload.
  • Heat Dissipation Design: The heatsink features a slot design to maximize surface area for efficient heat transfer to the surrounding air.
Close-up of the heatsink fins with blue arrows indicating heat dissipation through the slot design.

Figure 5: Slot Design for Heat Dissipation

Maintenance

The RAGEER M.2 SSD Heatsink requires minimal maintenance:

  • Dust Removal: Periodically inspect the heatsink for dust accumulation. If dust is present, gently clean it using compressed air or a soft brush to ensure optimal airflow and heat dissipation.
  • Thermal Pad Check: If you notice a decrease in cooling performance over time, you may inspect the thermal pad for degradation. If it appears dry or brittle, it may need to be replaced.

Troubleshooting

  • SSD Still Overheating:
    • Ensure the heatsink is properly installed and makes firm contact with the thermal pad and SSD.
    • Verify that the thermal pad is correctly placed over the SSD's heat-generating components.
    • Check your system's overall airflow. Poor case ventilation can limit the effectiveness of any heatsink.
  • Heatsink Feels Loose:
    • Re-adjust the rubber rings to ensure they are securely holding the heatsink in place.
    • Ensure the SSD is fully seated in its M.2 slot.

Specifications

FeatureDescription
BrandRAGEER
Model NumberN70
TypeM.2 SSD Cooler / Heatsink
MaterialAluminum Alloy
Dimensions (L x W x H)73mm x 23mm x 3.5mm
Heatsink Thickness3mm
Thermal Pad Thickness1mm
Cooling Effect5°C - 30°C reduction (environment dependent)
RGB SupportNo RGB
CompatibilityM.2 2280 SSDs (M Key, B Key)
IncompatibilityM.2 22x30, 22x40, 22x60 SSDs; mSATA SSDs
Diagram showing heatsink dimensions: 70mm length, 23mm width, 3mm thickness. Also shows 1mm thermal pad and an M.2 2280 SSD.

Figure 6: Heatsink Dimensions

Compatibility chart showing checkmarks for 22x110 and 22x80 M.2 SSDs, and crosses for 22x60, 22x40, 22x30. Also shows M Key and B Key compatibility with a check, and mSATA with a cross.

Figure 7: Universal Compatibility Overview

User Tips

  • This heatsink provides a basic yet effective cooling solution for M.2 2280 SSDs, helping to prevent performance degradation due to overheating.
  • For optimal cooling, ensure good airflow within your computer case.

Warranty and Support

For any product-related inquiries, technical support, or warranty claims, please contact your original seller or the RAGEER customer support channel. A detailed user manual in PDF format may also be available from the seller's product page.

© 2024 RAGEER. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.