1. Product Overview
1.1 Package Contents
- GMAIPOP F410 Main Dash Cam Unit
- Suction Cup Mount
- Rear Camera with Cable
- Car Power Adapter (Car Charger)
- USB Cable
- User Manual (this document)
1.2 Dash Cam Layout: Buttons and Ports
Familiarize yourself with the dash cam's controls and connections:
| No. | Feature | Description |
|---|---|---|
| 1 | Reset Hole | Insert a pin to reset the Dashcam. |
| 2 | Power Button | Long-press for ~3s to turn ON/OFF. |
| 3 | OK Button | Start/stop recording, play/pause video, enter/save menu settings. |
| 4 | Up Button | Scroll up in menus, switch display windows (front, rear, left/right), navigate to previous video files. |
| 5 | Down Button | Scroll down in menus, mute audio recording, navigate to next video files. |
| 6 | Menu/Mode Button | Long-press to enter Menu Settings (non-recording), short-press to exit Menu, short-press to enter Video Playback Mode (non-recording). |
| 7 | Power Slot (USB-C) | Connect USB cable or car charger. |
| 8 | Rear Camera Port | Connect the rear camera. |
| 9 | TF Card Slot | Insert a micro-SD card (up to 64GB, Class 10 recommended) for recording. |
| 10 | Fill Light | Automatic fill lights for right & left cameras in low light conditions. |
2. Setup and Installation
Watch the official installation video for a visual guide:
Video: GMAIPOP F410 Dash Cam Product Demonstration and Installation
2.1 Insert Micro-SD Card
- Ensure the dash cam is powered off.
- Insert a Class 10 or higher micro-SD card (up to 64GB) into the TF Card Slot (9) until it clicks into place.
- To remove, gently push the card in until it springs out.
2.2 Install Front Dash Cam
- Clean Windshield: Thoroughly clean the area on your windshield where you intend to mount the dash cam. Ensure it's free from dust, dirt, and grease.
- Prepare Suction Bracket: Insert the suction bracket into the designated slot on the dash cam. Ensure any protective film on the suction cup is removed.
- Attach to Windshield: Press the suction cup firmly against the cleaned windshield and engage the locking mechanism (if any) to secure it.
- Adjust Angle: Adjust the camera lens to point forward, centered on the road ahead.
Important Notes for Front Dash Cam Installation:
- Ensure the installation position is cleaned correctly.
- Verify the suction cup's film is removed and the cup is clean.
- Confirm the suction bracket is locked tightly to prevent the dash cam from falling during recording.
2.3 Install Car Charger
- Connect the car charger to the dash cam's USB-C Power Slot (7).
- Route the cable neatly along the windshield trim and dashboard to your car's cigarette lighter socket.
- Plug the car charger into the cigarette lighter socket.
Please Note:
- Always use the original car charger provided to avoid compatibility issues or damage.
2.4 Install Rear Camera
- Connect Rear Camera: Insert the rear camera's connector into the Rear Camera Port (8) on the main dash cam unit.
- Route Cable: Carefully route the rear camera cable:
- Hide the cable into the top panel/headliner.
- Slightly loosen side panels (A-pillar, B-pillar) to tuck the cable in, being cautious around airbags.
- Continue inserting the cable along the door's rubber seals towards the rear of the vehicle.
- Loosen the trunk's panel to route the cable to the desired mounting location for the rear camera.
- Connect to Reversing Light (Optional): Connect the rear camera's red cable to the positive pole of your car's reversing light. This enables the reversing image to display automatically on the dash cam screen when you shift into reverse. If you do not need this feature, you can skip this step.
- Mount Rear Camera: Attach the 3M sticky tape to the rear camera's bracket. Secure the rear camera in the middle, above your license plate frame, and adjust the angle.
- Final Connection: Connect the rear camera to its wired cable, ensuring the alignment arrows match for a proper connection.
Important Note:
- Ensure all connections are secure for optimal functionality of both front and rear cameras.
3. Operating Instructions
3.1 Power On/Off
- Automatic: The dash cam will power on automatically when your vehicle starts and power off when the engine is turned off (if connected to a switched power source).
- Manual: Long-press the Power Button (2) for approximately 3 seconds to manually turn the dash cam ON or OFF.
3.2 Recording
- Start/Stop Recording: Once powered on, the dash cam typically starts recording automatically. Short-press the OK Button (3) once to manually start or stop video recording.
- Loop Recording: The dash cam records in continuous loops (e.g., 1, 3, 5, or 10-minute segments). When the memory card is full, the oldest unlocked files will be overwritten.
- Audio Recording: The dash cam records audio by default. Short-press the Down Button (5) to mute or unmute audio recording during video mode.
3.3 Display Modes
Short-press the Up Button (4) to cycle through different display modes:
- Front Camera Only
- Rear Camera Only
- Left Camera Only
- Right Camera Only
- Picture-in-Picture (e.g., Front + Rear)
- All Four Cameras (Quad View)
Image: Front 1080P, Left/Right/Rear 720P views, and camera angle diagram.
Image: 360-degree wide-angle 4-lens panoramic monitoring with day and night recording examples.
3.4 Menu Navigation and Settings
- Enter Menu: While not recording, long-press the Menu/Mode Button (6) to enter the Menu Settings.
- Navigate: Use the Up Button (4) and Down Button (5) to scroll through menu options.
- Select/Confirm: Short-press the OK Button (3) to select an option or confirm a setting.
- Exit Menu: Short-press the Menu/Mode Button (6) to exit the menu.
3.5 Playback Videos
You can playback recorded videos directly on the dash cam or on a computer.
3.5.1 Playback on Dash Cam
- Stop Recording: Ensure the dash cam is not currently recording.
- Enter Playback Mode: Short-press the Menu/Mode Button (6) to enter Playback Mode.
- Navigate Files: Use the Up Button (4) and Down Button (5) to scroll through your recorded video files.
- Play/Pause: Short-press the OK Button (3) to play or pause the selected video.
- Delete/Protect: Long-press the Menu/Mode Button (6) to access options to delete or protect the current file.
- Exit Playback: Short-press the Menu/Mode Button (6) to exit Playback Mode.
3.5.2 Playback on PC
- Power off the dash cam and carefully remove the micro-SD card.
- Insert the micro-SD card into a card reader connected to your computer.
- Access the files on the SD card and play them using your preferred media player.
3.6 Connecting to Wi-Fi and App Control
The GMAIPOP F410 dash cam can be controlled and managed via the