Yinuogo YNG175

Contents

TO.GO 2WP Garage Remote Control User Manual

Model: YNG175 | Brand: Yinuogo

1. Introduction

This manual provides instructions for the setup, operation, and maintenance of your Yinuogo TO.GO 2WP Fixed Code Garage Remote Control. Please read this manual carefully before using the device to ensure proper function and longevity.

Front view of the TO.GO 2WP remote control

Figure 1: TO.GO 2WP Remote Control

2. Specifications

Feature Specification
Model Number YNG175
Brand Name Yinuogo
Encoding Method Fixed Code
Frequency 433.92MHz
Number of Buttons 2
Battery Included
Certification CE
Origin Mainland China

3. Package Contents

Your package should contain the following items:

  • 1 x Yinuogo TO.GO 2WP Remote Control (Model YNG175)
  • 1 x Battery (pre-installed)
The remote control in its retail packaging.

Figure 2: Remote Control in Packaging

4. Compatibility Notes

IMPORTANT: Please double check your existing remote control model and frequency before purchasing and setting up this device.

This remote control is designed for fixed code systems operating at 433.92MHz. It is NOT compatible with rolling code systems or other fixed code models not explicitly listed as compatible.

Compatibility diagram showing the TO.GO 2WP (Dip-Switch) is not compatible with Rolling Code remotes (2VA, 4VA, 2WV, 4WV).

Figure 3: Compatibility - Dip-Switch vs. Rolling Code

The TO.GO 2WP is specifically a Dip-Switch type remote. It is not compatible with the following models:

  • TO.GO - A
  • TO.GO 4AS
  • TO.GO 2AS
  • TO.GO 2AK
  • TO.GO 4QV
  • TO.GO - 4A
  • TO.GO 4AK
Incompatibility diagram showing the TO.GO 2WP is not compatible with TO.GO-A, TO.GO 4AS, TO.GO 2AS, TO.GO 2AK, TO.GO 4QV, TO.GO-4A, TO.GO 4AK models.

Figure 4: Incompatible Remote Control Models

5. Setup and Programming

To program your new TO.GO 2WP remote control, you will need to match its internal dip switch settings to those of your existing, working remote control.

  1. Open the Remote Control Shell: Carefully open the casing of your new TO.GO 2WP remote control. This usually involves removing a small screw or prying open the case with a small flat-head screwdriver.
  2. Locate Dip Switches: Inside the remote, you will find a bank of small switches (dip switches).
  3. Match Settings: Observe the position of the dip switches on your existing, working remote control. Each switch can be in an 'up', 'down', or 'middle' position.
  4. Set New Remote: Adjust the dip switches on your new TO.GO 2WP remote to exactly match the pattern of your existing remote.
  5. Close the Shell: Once the switches are set, carefully close the remote control shell, ensuring it snaps securely or the screw is re-inserted.
Image of the remote control with the battery compartment open, revealing the internal battery and dip switches.

Figure 5: Internal View showing Battery and Dip Switches

Note: If you do not have an existing remote, you may need to consult the manual for your garage door opener or gate system to find the correct dip switch settings.

6. Operating Instructions

After successful programming, operating your TO.GO 2WP remote control is straightforward:

  1. Point the remote control towards your garage door opener or gate receiver.
  2. Press one of the two buttons on the remote control.
  3. The garage door or gate should activate (open or close).

Ensure there are no obstructions in the path of the garage door or gate before activation.

7. Maintenance

7.1 Battery Replacement

The remote control uses a standard 12V battery (e.g., 23A type). When the remote's range decreases or it stops responding, it's time to replace the battery.

  1. Carefully open the remote control casing as described in the 'Setup' section.
  2. Remove the old battery from its compartment.
  3. Insert a new 12V battery, ensuring correct polarity (+ and -).
  4. Close the remote control casing securely.

7.2 Cleaning

Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or allow moisture to enter the device.

7.3 Storage

Store the remote control in a dry place, away from extreme temperatures and direct sunlight.

8. Troubleshooting

Problem Possible Cause Solution
Remote does not work after programming. Incorrect dip switch settings. Re-open the remote and carefully verify that the dip switch settings exactly match your original remote.
Remote has short range or intermittent operation. Low battery or interference. Replace the battery. Ensure no strong radio interference sources are nearby.
Remote is not compatible with my system. Your system uses rolling code or a different fixed code frequency/model. Verify your existing remote's type (fixed code/rolling code) and frequency (433.92MHz). Refer to Section 4: Compatibility Notes. This remote is for fixed code 433.92MHz systems only.

9. User Tips

  • Always keep a spare battery on hand for quick replacement.
  • If you have multiple remotes, label them to avoid confusion, especially if they control different devices.
  • For optimal range, ensure a clear line of sight between the remote and the receiver.

10. Product Video

Watch this video for a visual overview of the Yinuogo garage remote control.

Video: Yinuogo Garage Remote Control Overview

11. Warranty and Support

For any issues or questions not covered in this manual, please contact the seller or manufacturer's customer support. Keep your purchase receipt for warranty claims.

This product is certified with CE standards.

For additional information, you may refer to the official user manual PDF if available from the seller. (Reference: User manual (PDF))

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.