ZoeRax SC-UPC12-001

Contents

ZoeRax 1x2 FTTH Fiber Optic Splitter User Manual

Model: SC-UPC12-001

1. Product Overview

The ZoeRax 1x2 FTTH Fiber Optic Splitter is a passive optical device designed for efficient optical signal coupling, branching, and distribution. It utilizes an all-fiber structure, ensuring good environmental stability and low polarization-related losses, compliant with telecom-grade standards. This splitter is ideal for Fiber to the Home (FTTH) networks, allowing a single optical input to be distributed to two optical outputs.

Telecom Grade Cone Splitter
Figure 1: Telecom Grade Cone Splitter

2. Safety Guidelines

  • Handle fiber optic cables and connectors with care. Avoid touching the fiber end-faces directly.
  • Do not bend fiber optic cables beyond their minimum bend radius to prevent signal loss or damage.
  • Always use appropriate cleaning tools for fiber optic connectors to ensure optimal performance and prevent contamination.
  • Keep the splitter and all fiber optic components away from excessive heat, moisture, and direct sunlight.

3. Setup and Installation

  1. Inspect the Product: Upon receipt, carefully inspect the fiber optic splitter for any physical damage. Ensure all connectors are clean and free from dust caps.
  2. Confirm Compatibility: Verify that the connector types (SC UPC, SC APC, FC UPC) and fiber type (Singlemode G657A1) of the splitter match your existing fiber optic network infrastructure.
  3. Connect Input Fiber: Remove the dust cap from the input port (typically marked as 'IN' or '1') of the splitter. Carefully connect the incoming fiber optic cable from your optical network terminal (ONT) or distribution point to this port. Ensure a secure and clean connection.
  4. Connect Output Fibers: Remove the dust caps from the two output ports (typically marked as 'OUT1' and 'OUT2' or '2' and '3'). Connect your client-side fiber optic cables to these ports.
  5. Secure Cabling: Route and secure all connected fiber optic cables to prevent accidental disconnections or damage. Avoid sharp bends or excessive tension on the cables.
Widely Applicable Wavelengths
Figure 2: SC UPC Connectors and Wavelength Range (1310nm~1550nm)

4. Operating Instructions

The ZoeRax Fiber Optic Splitter is a passive device and requires no active configuration or power. Once properly installed, it will automatically split the incoming optical signal from the input port to the two output ports. It operates efficiently across a wide wavelength range of 1310nm to 1550nm, making it versatile for various optical network applications.

Uniform Spectral Distribution
Figure 3: Illustrative Diagram of Uniform Spectral Distribution

5. Maintenance

  • Connector Cleaning: Regularly inspect and clean fiber optic connectors using lint-free wipes and appropriate fiber optic cleaning solutions or tools. Contaminated connectors are a primary cause of signal loss.
  • Cable Management: Ensure all fiber optic cables are properly managed and protected. Avoid sharp bends, kinks, or excessive pulling force that can damage the fiber.
  • Environmental Protection: Keep the splitter in a clean, dry environment within its specified operating temperature range (-40°C to 85°C).

6. Troubleshooting

  • No Signal or Weak Signal:
    • Check all fiber optic connections to ensure they are fully seated and secure.
    • Clean all fiber optic connectors on both the splitter and connected cables.
    • Inspect cables for any visible damage (e.g., sharp bends, cuts).
    • Use an optical power meter to verify signal strength at the input and output ports. Compare with expected insertion loss values.
  • Intermittent Connection:
    • Ensure connectors are not loose.
    • Check for any physical stress on the fiber cables near the connectors.
  • Abnormal Functionality: If issues persist after basic troubleshooting, contact customer support for assistance.
Low Insertion Loss Diagram
Figure 4: Insertion Loss Values for Different Split Ratios (1x2: ≤3.5dB)

7. Specifications

FeatureSpecification
BrandZoeRax
Model NumberSC-UPC12-001
Product Type1x2 FTTH Fiber Optic Splitter (FBT Coupler)
Fiber TypeSinglemode G657A1
Operating Wavelength1310nm / 1550nm
Number of Interfaces1 Input, 2 Outputs
Connector ModelsSC UPC, SC APC, FC UPC (depending on variant)
Insertion Loss (1x2)≤3.5dB
Working Temperature-40°C to 85°C
Housing MaterialABS Resin Synthetic Plastic
Plug TypeThree Ring Ceramic Plug
Product Parameters Table
Figure 5: Summary of Product Parameters

8. User Tips

No specific user tips were available from provided reviews or Q&A content for this product.

9. Warranty and Support

This ZoeRax Fiber Optic Splitter comes with a 12-month warranty from the date of purchase. For warranty claims, technical support, or any inquiries regarding the product, please contact your seller or the ZoeRax official support channel. Please refer to the official user manual PDF for additional details: View User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.