tedeligo TD11

Contents

User Manual: 433MHz Wireless Remote Control Light Switch

Model: TD11 | Brand: Tedeligo

1. Introduction

This manual provides detailed instructions for the installation, operation, and programming of your 433MHz Wireless Remote Control Light Switch. This device allows for convenient wireless control of lighting and other electrical appliances, offering multiple operating modes to suit various needs.

2. Safety Warnings

  • Always ensure the power supply is disconnected before performing any installation or maintenance.
  • Connect the wires correctly according to the circuit diagram. Incorrect wiring can lead to electric shock or device malfunction.
  • When fixing wires, do not touch metal parts on the circuit board by hand to avoid electric shock.
  • Place the receiver in a stable, safe, and not easily touched location.
  • The output type is passive output/potential-free contacts.
  • Do not expose the device to excessive moisture or extreme temperatures.

3. Specifications

3.1. Relay Receiver Board (Model: TD11)

ParameterValue
Working VoltageAC100V~250V
Input/Output1V~250V
Max Current10A
RF Frequency433.92Mhz
Pin ConfigurationL/N/COM/NO
Receiver Size28*22*47 mm
Working Temperature-30~+80 Celsius
Receiving Sensitivity>-97dbm
Storage CapacityUp to 20 remote controls
Support Encoding1527 Learning code
RF Operating ModeASK superheterodyne wireless reception
Remote Operating ModesMomentary, Toggle, Latched, Time Delay

3.2. Wall Panel Switch

ParameterValue
Size86*86 mm
Battery1*CR2032 (Included)
Code1527 learning
FeaturesDouble-sided tape and screws for mounting, battery base
Wireless RangeUp to 50m in open space

4. Package Contents

Depending on your order, the package typically includes:

  • 1x Relay Receiver Board
  • 1x Wall Panel Switch (with 1*CR2032 battery installed)
  • Double-sided tape for mounting
  • Screws for mounting
Image showing one receiver board, one wall panel switch, a CR2032 battery, double-sided tape, and screws.
Figure 1: Typical package contents (1 receiver + 1 panel switch shown).

5. Installation

Before proceeding with installation, ensure the main power supply is turned off at the circuit breaker to prevent electric shock.

5.1. Wiring the Receiver

Connect the receiver according to the appropriate wiring diagram for your application. The receiver supports AC 100-250V input/output and has L (Live), N (Neutral), COM (Common), and NO (Normally Open) pins.

Wiring diagram for connecting the receiver to an AC 100-250V power source and a light fixture, showing L, N, NO, COM terminals.
Figure 2: Basic wiring diagram for AC 100-250V light control.
Wiring diagram for connecting the receiver to a garage door opener system.
Figure 3: Wiring diagram for garage door systems (passive output).
Wiring diagram for connecting the receiver to a DC device with 1-250V voltage.
Figure 4: Wiring diagram for DC device control (1-250V).

5.2. Mounting the Wall Panel Switch

The wall panel switch can be mounted using the provided double-sided tape or screws. Ensure the mounting surface is clean and dry.

Diagram showing the wireless control distance of up to 50 meters from the wall switch to the receiver.
Figure 5: Wireless control distance up to 50 meters.

6. Operating Modes

The receiver supports four different operating modes, which can be programmed using the wall panel switch or other 433MHz remote controls.

  • Momentary Mode: Press and hold the button to turn the device ON; release the button to turn the device OFF.
  • Toggle Mode: Press the button once to turn the device ON; press the same button again to turn the device OFF.
  • Latched Mode: Press button 'A' to turn the device ON; press button 'B' to turn the device OFF. (Requires a remote with at least two distinct buttons).
  • Time Delay Mode: Press and hold button 'A' to turn the device ON; release the button, and the device will turn OFF after a set delay (5, 10, 15, or 20 seconds).
Diagram illustrating multiple wall switches controlling one light, and one wall switch controlling multiple lights.
Figure 6: Flexible control configurations (many-to-one or one-to-many).

7. Programming Instructions

The receiver and transmitter are usually paired at the factory. If not, or if you wish to change the operating mode, follow these steps. Always reset the receiver before changing the operating mode.

7.1. Resetting the Receiver

  1. Press the learning button on the receiver 8 times.
  2. The indicator LED on the receiver will blink several times and then turn off, indicating a successful reset.

Note: After a reset, all previously paired remote controls will no longer work and must be reprogrammed.

7.2. Programming Operating Modes

After resetting, follow the steps below to program your desired operating mode:

  • Momentary Mode:
    1. Press the learning button on the receiver once. The indicator LED will turn ON.
    2. Press the desired button (e.g., 'A') on your remote control once. The indicator LED will blink and then turn OFF.
    3. Programming is successful.
  • Toggle Mode:
    1. Press the learning button on the receiver twice. The indicator LED will turn ON.
    2. Press the desired button (e.g., 'A') on your remote control once. The indicator LED will blink and then turn OFF.
    3. Programming is successful.
  • Latched Mode:
    1. Press the learning button on the receiver 3 times. The indicator LED will turn ON.
    2. Press button 'A' on your remote control once.
    3. Press button 'B' on your remote control once. The indicator LED will blink and then turn OFF.
    4. Programming is successful. (Requires a remote with at least two distinct buttons).
  • Time Delay Mode:
    1. Press the learning button on the receiver 4, 5, 6, or 7 times for 5, 10, 15, or 20 seconds delay respectively. The indicator LED will turn ON.
    2. Press the desired button (e.g., 'A') on your remote control once. The indicator LED will blink and then turn OFF.
    3. Programming is successful.

7.3. Visual Programming Guide

For a visual demonstration of the programming steps, please refer to the official product video:

Video: Demonstrates working modes, wiring, reset, and programming for Momentary, Toggle, Latched, and Time Delay modes.

8. User Tips

  • If you find the written programming instructions confusing, watching the official product video (Section 7.3) can make the process much clearer and easier to understand.
  • For optimal wireless range, ensure the receiver's antenna is fully extended and not obstructed by metal objects.

9. Troubleshooting

If the receiver and transmitter are not functioning normally, try the following steps:

  1. Check Battery: Verify if the battery in the wall panel switch (CR2032) is exhausted. If the indicator LED does not light up or is dim, replace the battery.
  2. Check Wiring: Ensure all wiring connections to the receiver are correct and secure according to the circuit diagrams.
  3. Reprogram: Try resetting the receiver (Section 7.1) and then reprogramming the desired operating mode (Section 7.2).
  4. Signal Interference: Ensure there are no strong sources of RF interference nearby.

10. Maintenance

  • Battery Replacement: Replace the CR2032 battery in the wall panel switch promptly when its voltage is low (e.g., indicator LED is dim or unresponsive).
  • Antenna: Extend the receiver's antenna for better signal reception.
  • Cleaning: Clean the devices with a dry, soft cloth. Do not use harsh chemicals or abrasive cleaners.

11. Warranty & Support

This product comes with a 1-year warranty from the date of purchase.

For any questions or support regarding this product, please contact us:

  • WhatsApp: +15766861142
  • Email: tedeligoservice@163.com

You may also find additional resources and the full user manual in PDF format here.

12. Certifications

This product is certified to meet the following standards:

  • CE
  • FCC
  • ROHS
Image showing CE, FCC, and RoHS certification documents for the product.
Figure 7: Product Quality Assurance and Certifications.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.