1. Introduction
Thank you for purchasing the M8AC balance charger. Please read this manual carefully before use to ensure proper operation and safety.
Key Points
- Tips: Helpful advice for optimal use.
- Important: Critical information to prevent damage or injury.
- Information: General details about features and functions.
Further Information
To ensure you have the best experience with this product, stay updated with news, information, and firmware updates for your charger. This information can typically be found on the manufacturer's official website.
2. Safety Instructions
Failure to follow these safety instructions may result in fire, electric shock, or other injury or damage.
- The M8AC allows input voltage of DC 7-35V or AC 100-240V. Ensure the charger is only connected to a suitable power source and with correct polarity.
- Do not use this product in hot, humid, flammable, or explosive environments.
- Please do not use this charger without supervision. Never leave charging batteries unattended.
- When not using this product, please unplug the input power.
- When using the charging function, please set a current that matches the battery. Do not set an excessive current for charging to avoid damage to the battery. Check the guidelines of your battery's manufacturer for correct charging instructions.
3. Product Description
The M8AC is a multifunctional tool that integrates functions such as a balance charger and discharger, a signal measuring device, and a signal source.
- Supports AC or DC dual input.
- Charges, discharges, and balances (where applicable) LiPo, LiHV, LiFe, Lilon, LTO 1-8S, NiMH 1-20S, PB 1-12S batteries.
- Charge current: MAX 20A @MAX600W.
- Discharge current: Recycle Max 20A@600W, Internal mode Max 3A @20W.
- TYPE-C fast charger output MAX 20.0V 65W.
- Lithium battery cut-off voltage can be adjusted (TVC function).
- Measures battery voltage, battery internal resistance, and balances lithium packs automatically.
- Measures / outputs PWM/PPM/SBUS standard signals with an accuracy of 1 us.
- Constant current and constant voltage source output, customizable 1-35V constant voltage, 0.5-20A constant current.
- Can be adapted for charging consumer-grade drone batteries.
- Multi-language user interface.
- Easily upgradable via USB.
4. Package Contents
Please check the package contents upon unboxing. If any items are missing or damaged, contact your retailer.
- ToolkitRC M8AC Smart Charger
- AC Power Cable (EU or US plug, depending on region)
- USB Cable
- User Manual

For non-visual users: The image displays the ToolkitRC M8AC charger alongside its retail box, an EU-style power cable, and a USB cable, illustrating the typical contents of the product package.
5. M8AC Layout

For non-visual users: The image shows two views of the M8AC charger. The top view displays the front and side, highlighting the display screen, exit button, scroll wheel, output port (XT60), balance port, signal port, and TYPE-C output. The bottom view shows the rear of the unit, featuring the AC input, cooling fan, and DC input (XT60).
Front Panel
- Display: 2.4-inch IPS LCD screen.
- Exit button: For navigating menus and exiting functions.
- Scroll wheel: For menu navigation, parameter adjustment, and selection.
- Output port: Main battery connection (XT60).
- Balance port: For cell balancing (JST-XH compatible).
- Signal port: For PWM/PPM/SBUS signal measurement and output.
- TYPE-C output: For fast charging external devices.
Rear Panel
- AC input: For connecting to mains power (100-240V AC).
- Cooling fan: For heat dissipation during operation.
- DC input: For connecting to a DC power source (7-35V DC, XT60).
6. Setup and Quick Start
6.1. Input Power Connection
- Connect a 7-35V DC power supply (via XT60) or an AC 100-240V power supply (via IEC C14 inlet) to the input port on the back of the M8AC.
- Ensure the power source is stable and provides sufficient current for your charging needs.
6.2. Quick Start Guide
- After connecting power, the display will show the boot logo for 2 seconds. A welcome sound will play simultaneously.
- The screen will then enter the main interface, displaying input voltage, current, temperature, and cell voltages.
- Auxiliary Functions: Press and hold the [Exit] button to enter the auxiliary function interface. Scroll the [Scroll Wheel] to switch between pages.
- Charging Parameters: With the charger idle, short press the [Scroll Wheel] to set charging parameters. During charging, short press the [Scroll Wheel] to adjust amperage or stop the process.
- System Settings: With the charger idle, press and hold the [Scroll Wheel] to enter the system setting interface.
- Navigation: Short press [Exit] to return to the previous interface.
7. Operating Instructions
7.1. Charge and Discharge Settings
From the main interface, short press the [Scroll Wheel] to enter the charging function. If battery selection is enabled in system settings, a battery selection menu will appear. Otherwise, it will go directly to the current battery profile.
7.1.1. Battery Type Setting
Scroll the [Scroll Wheel] to select a preset or create a new battery profile (up to 32 files). Short press the [Scroll Wheel] to enter specific battery settings.
- Move cursor to [Battery Type] and short press [Scroll Wheel] to modify.
- Supported types: LiPo, LiHV, LiFe, Lilon, LTO, NiMH, PB, and Smart Battery mode.
- Warning: Ensure correct battery type is selected to prevent damage or fire.
Battery Type Glossary:
- LiPo: Lithium Polymer, nominal 3.70V, full 4.20V.
- LiHV: High-Voltage Lithium, nominal 3.85V, full 4.35V.
- LiFe: Iron-Lithium, nominal 3.30V, full 3.60V.
- Lilon: Lithium-Ion, nominal 3.60V, full 4.10V.
- LTO: Lithium-Titanate, nominal 2.40V, full 2.70V.
- NiMH: Nickel-Metal Hydride, nominal 1.20V.
- PB: Lead-Acid, nominal 2.00V.
7.1.2. Cell Setting
Move cursor to [Cells] and short press [Scroll Wheel] to modify cell count (1S-8S for Lithium, 1S-20S for NiMH, 1S-12S for PB). When set to [Auto], the charger identifies cell count from total voltage and balance port data.
- Tip: Over-discharged/charged batteries may cause incorrect cell count; adjust manually. Incorrect cell count can lead to overcharging and fire risk. Connecting the balance port improves accuracy.
7.1.3. Work Mode
Move cursor to [Mode] and short press [Scroll Wheel] to modify. Options include: Charge, DisCHG (Discharge), StoCHG (Storage Charge).
- LiPo, LiHV, LiFe, Lilon, LTO: Charge, Discharge, Store, Destroy.
- NiMH: Charge, Discharge, Cycle, Destroy.
- PB: Charge, Discharge, Destroy.
7.1.4. Discharge Mode
Available under discharge, storage, and cycle modes. Options: Inter (Internal) and Recycle.
- Internal Mode: Uses internal heat dissipation, max 3.0A@20W.
- Recycle Mode: Recovers power to the input battery (if battery is input source), max 20.0A@600W. To activate, set Power type to 'Battery' in system settings.
7.1.5. Max Input Voltage (for Recycle Mode)
If Recycle mode is selected, set [Max Input Vol.]. If input voltage reaches this value during discharge, the process stops. Set this to the highest protection voltage of your power supply to avoid damage.
7.1.6. End Voltage Setting (TVC)
Move cursor to [End Voltage] and short press [Scroll Wheel] to modify individual cell end voltage (0.01V step).
- Charging: Charge cut-off voltage (±50mV of full voltage).
- Discharging: Discharge cut-off voltage.
- Only for LiPo, LiHV, LiFe. Do not modify if unfamiliar with battery characteristics.
7.1.7. Current Setting
Move cursor to [Charge Current] or [DisCHG Current] and short press [Scroll Wheel] to modify (0.1A step). Charger supports up to 20.0A.
- Tip: Set charging rate to 1-2C (e.g., 2000mAh battery = 2.0-4.0A). Current settings are only valid in their respective work modes.
7.1.8. NiMH Setting (PeakV)
For NiMH battery type, set the peak voltage value (5mV-15mV) when fully charged. This is the maximum voltage drop per cell.
7.1.9. Cycle Setting (for NiMH)
Under NiMH cycle mode, options for Cycle time (2-12 cycles) and Rest time (2-10 minutes) appear. The pattern is discharge -> charge.
7.1.10. Smart Battery Setting (UAV)
When UAV battery is selected, set Drone model and Max current (0.5A-20A).
7.2. Charge and Discharge Work
When charging/discharging starts, the charger enters a work interface displaying real-time data.

For non-visual users: The image shows the M8AC screen during charging. It displays input voltage (23.21V), accumulated energy (372Wh), internal temperature (40.6°C), main port voltage (23.99V), main port current (3.99A), elapsed time (172:57), charged capacity (11.5Ah), and individual cell voltages (e.g., 3.988V for cell 1, 3.988V for cell 2, etc.).
- Rotate [Scroll Wheel] to toggle between three displays: main data, internal resistance, and general info.
- Short press [Scroll Wheel] to dynamically set charge current or stop charging.
- Upon completion or error, a popup and audible tone will occur.
- Tips: Never leave cells unattended. Lithium battery balancing only occurs if the balance plug is connected. Charging will auto-start for the next battery if disconnected after full charge; ensure cell count matches.
7.3. Accessibility (Auxiliary Functions)
Long press [Exit] from the main interface to enter auxiliary functions.
7.3.1. Measure Resistance
Short press [Scroll Wheel] to test internal resistance of connected battery.
7.3.2. Measure Signal
Enter signal test interface, scroll [Scroll Wheel] to select signal type (PWM, PPM, SBUS).
7.3.3. Signal Output
Enter signal output interface, select signal type (PWM, PPM, SBUS). Set output mode (manual, auto 1/2/3). In manual mode, adjust pulse width and cycle values.
7.3.4. ESC Test
Enter ESC test mode, adjust pulse width/cycle values.
7.3.5. Power (Adjustable Power Supply)
Set output voltage and current. Move cursor to start, short press [Scroll Wheel] to begin power output.
7.4. Other Functions
7.4.1. Firmware Upgrade
Connect M8AC to computer via USB. It will appear as a USB drive named 'Toolkit'. Download 'app.upg' from the official ToolkitRC website and overwrite the file in the drive to upgrade firmware.
7.4.2. TYPE-C Output
TYPE-C USB supports 20.0V 65W output for charging mobile devices.
7.4.3. Automatically Continue Charging/Discharging
When a battery is fully charged, connect the next battery. The device will automatically continue. This function can be started/stopped in the settings menu.
7.4.4. Fan Level
Fan starts at 40°C, speed increases with temperature. With AC input, if power > 100W, fan runs at full speed.
7.4.5. Manual Voltage Calibration
With M8AC off, press and hold [Scroll Wheel], then connect power. System enters calibration mode. Use a voltmeter to measure actual voltage, adjust values on screen, then save.
7.4.6. Full Charge Mode
When lithium battery is fully charged, it prompts 'Fast charge complete'. If not removed, charger trickle charges until disconnected.
8. System Settings
Press and hold [Scroll Wheel] from the main interface to enter system settings. Short press to expand settings.
8.1. Input Settings
- Power select: Preset power 1, 2, 3.
- Power type: Battery pack (enables recycle mode) or Adapter (disables recycle mode).
- Max power: Maximum wattage allowed via input port during charging.
- Max current: Maximum current allowed via input port during charging.
- Voltage range: Input voltage range.
8.2. Security Settings
- Safe inter Temp.: Charging stops if device temperature exceeds this value.
- Safe Exter Temp.: Charging stops if environment temperature exceeds this value.
- Safe time: Maximum time limit for continuous charging/discharging.
- Safe capacity: Maximum accumulated capacity for a session.
8.3. Personalization
- Backlight: Display brightness level (1-10).
- Operation volume: Volume level (0-10, 0 for silent).
- Announce volume: Volume for announcements.
- Warning volume: Volume for warnings.
- Language: System display language (English, Chinese, etc.).
- Theme style: Light or dark themes.
8.4. Other System Options
- Battery selection: Show/hide frequently used parameters (default: OFF).
- Continuous work: Enables/disables continuous charging/discharge after battery replacement (default: OFF).
- Work completed: Stop or trickle charge after completion (default: not trickle).
- Balance start Vol: Balance cells prior to full current charge.
- Default: Restore factory settings.
- ID: Independent ID for each device.
9. Maintenance
- Cleaning: Use a soft, dry cloth to clean the charger. Do not use solvents or abrasive cleaners. Ensure no liquids enter the device.
- Storage: Store the charger in a cool, dry place away from direct sunlight and extreme temperatures.
- Inspection: Periodically check cables and connectors for any signs of wear or damage. Replace damaged components immediately.
- Ventilation: Ensure the cooling fan and vents are free from dust and obstructions to maintain proper airflow.
10. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Charger does not power on | No power input; incorrect voltage/polarity | Check power cable connection; verify input voltage (AC 100-240V or DC 7-35V) and polarity. |
| Charging error message | Incorrect battery type/cell count; battery fault; over-temperature | Verify battery type and cell count settings; inspect battery for damage; check charger/environment temperature. |
| Battery not balancing | Balance lead not connected or faulty | Ensure balance lead is securely connected to the balance port. |
| Charger gets hot | High current charging/discharging; obstructed fan | Ensure adequate ventilation; check fan for obstructions; reduce charge/discharge current if necessary. |
| Inaccurate voltage readings | Needs calibration | Perform manual voltage calibration as described in the 'Other Functions' section. |
11. Specifications
| Feature | Specification |
|---|---|
| Input Voltage | AC 100-240V @MAX 2.5A, DC 7-35V @MAX 25A |
| Battery Type | LiPo/LiHV/LiFe/Lilon/LTO (1-8S), NiMH (1-20S), PB (1-12S) |
| Balance Current | 1000mA @4.2V |
| Balance Accuracy | <0.005V |
| Charge Power | 0.1-20A @ DC600W/AC 200W |
| Discharge Power | 0.1-20A @600W (Recycle Mode), 0.1-3A @20W (Internal Mode) |
| TYPE-C Output | MAX 20.0V @65W |
| Battery Voltage Range | 1.0V-5.0V @1-8S |
| Internal Resistance | 0.1mΩ-99mΩ @1-8S |
| Signal Measurement (PWM) | 880us-2200us @20-400Hz |
| Signal Measurement (PPM) | 880us-2200us*8 CH @20-50Hz |
| Signal Measurement (SBUS) | 880us-2200us*16 CH @20-100Hz |
| Signal Output (PWM) | 500us-2500us @20-1000Hz |
| Signal Output (PPM) | 880us-2200us*8 CH @50Hz |
| Signal Output (SBUS) | 880us-2200us*16 CH @74Hz |
| Power Output (Mode) | 0.5-15A @1-28V (CC+CV) |
| Display | IPS 2.0 inch, 320*240px |
| Product Size | 108 × 113 × 62mm |
| Product Weight | 500g |
| Individual Packing Size | 136 × 153 × 67mm |
| Individual Packing Weight | 600g |
12. User Tips
- Reliability: Users report the M8AC charger is reliable, with some units working continuously for extended periods without issues.
- Build Quality: The device features a high-quality, durable plastic casing, contributing to its robust feel.
- Ease of Use: The interface is generally considered intuitive and easy to navigate, making it user-friendly for various tasks.
- Language Settings: While multi-language support is available, some users note that non-English translations (e.g., Russian) might be poor. It's advisable to use English if you encounter difficulties with other language options.
13. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the official ToolkitRC website or contact your authorized dealer. Keep your proof of purchase for warranty claims.